Panasonic DMP-BD85EGK operating instructions Messages, On the television, On the unit’s display

Page 32

Messages

The following messages or service numbers appear on the television or unit’s display when something unusual is detected during startup and use.

On the television

Cannot play.

¾You inserted an incompatible disc (Discs recorded in PAL video, etc.).

Cannot display on this unit.

¾You tried to play a non-compatible image.

¾Confirm “SD” on the unit’s display is not blinking and re-insert the card.

No disc is inserted.

¾The disc may be upside down.

$This operation is not available.

¾Some operations are unsupported by the unit. For example;

–BD-Video: During playback, reverse slow-motion or reverse frame-by-frame is not possible.

IP address is not set.

¾The “IP Address” in “IP Address/DNS Settings” is “---. ---.

---. ---”. Set the “IP Address”, “Subnet Mask”, and “Default Gateway”. (Select the automatic address acquisition if necessary.)

On the unit’s display

F99

¾The unit fails to operate properly. Press [POWER Í/I] on the main unit to switch the unit to standby for 3 seconds. Now press [POWER Í/I] on the main unit again to turn the unit on.

HDMI ONLY

¾Some BD-Video discs can only be output with HDMI.

NET

¾Displays while VIERA CAST is starting up.

No PLAY

¾There is a viewing restriction on a BD-Video or DVD-Video. (> 26)

No READ

¾The media is dirty or badly scratched. The unit cannot play.

PLEASE WAIT

¾The unit is carrying out an internal process. This is not a malfunction. You cannot operate the unit while “PLEASE WAIT” is displayed.

REMOVE

¾The USB device is drawing too much power. Remove the USB device.

SET 

(“ ” stands for a number.)

¾The remote control and main unit are using different codes. Change the code on the remote control.

Press and hold [OK] and the indicated number button at the same time for more than 5 seconds.

U59

¾The unit is hot.

The unit switches to standby for safety reasons. Wait for about 30 minutes until the message disappears.

Select a position with good ventilation when installing the unit. Do not block the ventilation hole on the rear and side of the unit.

U72

U73

¾The HDMI connection acts unusually.

–Turn the unit and TV off.

–Disconnect the HDMI cable between the player and the TV.

Hor F

(“ ” stands for a number.)

¾There is something unusual.

¾Check the unit using the troubleshooting guide. If the service number does not disappear, do the following.

1 Disconnect the plug from the AC outlet, wait a few seconds, then reconnect it.

2Press [POWER Í/I] to turn the power on.

If the service number does not disappear despite doing the above, request service from the dealer. Inform the dealer of the service number when requesting service.

START

¾The system is being restarted during the firmware update. Please do not turn off power.

UPD/

(“ ” stands for a number.)

¾The firmware is being updated. Please do not turn off power.

FINISH

¾The firmware update is complete.

32

VQT2H76

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Model No. DMP-BD85 If you have any questions contactImportant Safety Instructions Following Applies only in the U.S.A. FCC NoteTable of contents Unit and media care AccessoryUsing the remote control Pull to flip down the front panel Power button Power Í/IControl reference guide Type Logo examples Type detail Playable contents Playable discs/Cards/USB devicesDiscs that cannot be played in this unit Region management informationFinalize BD-VideoConnecting to a TV VideoConnecting to an amplifier/receiver Digital AudioAnalog Audio      Cable connectionsConnecting to a broadband network Precautions of Wireless LAN AdaptorFollowing Applies only in Canada Connecting to an AC powerFollowing Applies in the U.S.A. and Canada Network Easy Setting SettingEasy Setting Access Point Connection Setting Network Easy Setting Connection CheckNetwork Easy Setting Internet Connection Check Display Check the followingReprogramming the remote control Firmware updatesFor other Panasonic products For TV or amplifier/receiverTo switch drives Inserting or removing a mediaFunctions menu BD/DVD/CDPlaying video contents Useful functions Press SUB Menu Select an item, then press OKDeleting data/Formatting SD cards Press PIPConnect to the network Insert the discAbout Divx Video About Divx VIDEO-ON-DEMAND Regarding DivXDisplaying subtitles text Playing still pictures To show the picture propertiesInsert a disc, SD card or USB device Press 3, 4, 2, 1 to select the album and press OKPlaying music Playing a track in another folderInsert a disc or USB device Press 3, 4 to select the track and pressEasy control only with Viera remote control Linked operations withPreparation Press SUB Menu Select an item, then press OK Viera LinkTM is a new name for EZ SyncTMPress 3, 4, 2, 1 to select the item and press OK Enjoying Viera CasttmPress Viera Cast Playback menu DiscAudio PlayVideo Setup menu Display TV / Device Connection Network OthersCannot eject disc Troubleshooting guideGeneral operation Network & Viera Cast PicturePlayback On the unit’s display MessagesOn the television Hdmi AV OUT/DIGITAL Audio OUT Coaxial/Optical Audio InformationAbout audio from audio output terminals Recommended audio output setting For details of the each item, refer toAbout MP3/JPEG/DivX/ AVCHD/MPEG2 files DivXSubtitles text file of DivX MP3Structure of folders that can be played in this unit Specifications Supplemental information Glossary AvchdBD-J DTS-HDProduct or Part Name Parts Labor As of NovemberLimited Warranty Only for Canada Warranty ServiceIf YOU Ship the Product to a Servicentre Limitations and ExclusionsReproducción básica Referencia rápida enConexiones básicas Contact Information cdrequest@am-linux.jp AC Power Connection Angle Audio Off Timer On-screen Language Picture-in-picture PlaybackIndex Local storage M MPEG2 MP3 Network
Related manuals
Manual 44 pages 63.73 Kb
Top Page Image Contents