Sharp BD-HP22H operation manual Quick Start, Auto Power Off, Audio Out Dynamic Range Control

Page 41

SETTINGS

Audio Out

Dynamic Range Control

You can set the audio output when connecting to SURROUND equipment.

1This sets the audio output connected to SURROUND equipment.

Item

HDMI Output: Select this when you connect using HDMI OUT terminal.

Digital Output: Select this when you connect using DIGITAL AUDIO OUT terminal (OPTICAL).

2ch Audio Output: Select this when you do not use SURROUND sound equipment.

2You can set the audio output mode for each output terminal.

1This sets the audio output mode for HDMI OUT terminal when selecting “HDMI Output”.

NOTE

When the secondary audio is set to “On”, PCM is automatically selected as the audio output mode.

This lets you adjust the range between the loudest and softest sounds (dynamic range) for playback at average volume. Use this when it is hard to hear dialogue.

Item

Normal: The same audio output range is played as the original recorded audio output range.

Shift*: When Dolby Digital audio is played back, the dynamic range of the audio is adjusted so that the dialogue portion can be heard easily. (If the audio sounds abnormal, set to “Normal”.)

Auto: When you play back audio in the Dolby TrueHD format, the dynamic range is automatically adjusted.

*Lower the audio volume before setting. If you do not do so, the speakers may emit a loud sound or excessive output may be applied to the speakers.

Quick Start

This turns the Quick Start function on and off. When the Quick Start function is on:

Item

Bitstream:

PCM (Surround):

Select this when connecting to HDMI equipment with a built-in decoder for DOLBY DIGITAL, etc.

Setting to Bitstream will output each audio signal by Bitstream.

Select this when connecting to multi-channel HDMI equipment.

Setting to PCM (Surround) will output by LINEAR PCM by decoding audio signals recorded in each audio output mode such as

DOLBY DIGITAL, DTS.

The startup time of the Player is reduced.

However, power consumption will increase.

When the Quick Start function is off:

The player will enter the low power consumption mode when in standby condition.

Item

Yes, No

NOTE

When “Quick Start” is set to “Yes”, the Player requires some time to turn off.

2This sets the audio output mode for DIGITAL AUDIO OUT (OPTICAL terminal) when selecting “Digital Output”.

Item

Bitstream:

Select this when connecting to

 

 

SURROUND equipment with

 

 

a built-in decoder for DOLBY

 

 

DIGITAL, etc.

 

Setting to Bitstream will output

 

 

each audio signal by Bitstream.

PCM:

Select this when connecting to 2

 

 

channel stereo audio equipment.

 

Setting to PCM will output by

 

 

converting each audio signal into

 

 

PCM 2 channel audio signal.

NOTE

See page 45 for information on output of next generation audio formats.

MPEG Audio is only output as PCM (STEREO) 48kHz.

Auto Power Off

This sets the Player so that power is automatically shut off if playback is stopped for about 10 minutes.

Item

Yes, No

AQUOS LINK

This lets you set the Player to receive the control signal from the AQUOS LINK remote control via the HDMI cable.

Item

Yes, No

NOTE

For details, refer to the operation manual of TV.

If “Component” is selected from the “Video Out Select” menu, AQUOS LINK is not available. Select “HDMI” if you want to use AQUOS LINK features.

Settings

39

Image 41
Contents BD-HP22H Blue Neutral Brown Live Special Note for Users in the U.KIntroduction Power Cord ProtectionContents What would you like to do with this Player? Dear Sharp Customer Additional Safety InformationIntroduction Information on Battery DisposalBattery supplied with this product contains traces of Lead Information on Disposal for Business Users Information on Disposal for Users private householdsEuropean Union Other Countries outside the EUBlu-ray Disc About DiscsTypes of Discs that Can Be Used with This Player Discs that Cannot Be Used with This PlayerAbout the Jpeg file format About DiscsAbout Disc Contents Copyright Disc PrecautionsImportant Information Getting Started Adjust settingsUnpacking Selecting equipment to connectMain Unit Front Major ComponentsMain Unit Rear Hdmi cable holder on the rear of the main unitKeylock function Remote Control UnitMajor Components Video terminals/jacks on this Player Introduction to ConnectionsAnalogue audio connection Broadband Internet connectionVideo Connections Connecting to the Hdmi TerminalThis Player Equipment with an Hdmi terminalVideo equipment with component jacks Connecting to the Component JacksVideo Connections Video equipment with a video jack Connecting to the Video JackYou can enjoy the images through the video jack Connect directlyAudio Connections Connecting to the Digital Audio TerminalAudio equipment with a digital audio input terminal To Optical Input terminalAudio equipment with audio jacks Connecting to the Audio JacksAudio Connections Broadband Internet Connection Connecting to the Ethernet terminalExample of a Broadband Internet Connection To LAN terminalApproximate operating range of remote control Loading the Batteries in the Remote ControlConnecting the Power Cord Before Starting PlaybackIndicators on the Player Turning the Power OnTurning the power on Entering standbyOperating a Sharp TV Using the Remote Control Language SettingPress Setup to display the Setup Menu screen Changing the on-screen display languageTurning Off the LCD Backlight and Indications Using Aquos LinkControlling the Blu-ray disc player using Aquos Link Loading a Disc BD/DVD/CD PlaybackDisplaying the disc information BD/DVD Video PlaybackUsing the pop-up menu Using the disc menuBD/DVD Menus Start playback by selecting a title from the top menuVirtual Package Enjoying Bonusview or BD-LIVEDisc PlaybackPlayback by selecting a title DVD-R/-RW/BD-RE/-R PlaybackAbout Title List ThumbnailPlaying back the title you stopped while being played Sorting the titles Playback by selecting a PlaylistAudio CD Playback Operation procedure for the Functions menuPlayback from the beginning Playback by selecting a trackFast Forward/Reverse Search Playback FunctionsPause/Frame Advance Playback Slow PlaybackStereo is displayed. Audio cannot be switched Switching SubtitlesPartial Repeat Playback Repeat Playback of a Specified Part Displaying the Audio InformationDisplaying the Angle Mark Switching the AngleJpeg File Playback Setting slide show speed/repeat playbackPlaying back Slide Show Playing back still images in sequenceFunction Control Settings During PlaybackFunction control operation procedure Functions which can be set Settings During PlaybackWhen setting the PIN code for the first time Basic Operation for Playback SettingSettings Common operationsAudio Video Settings When the Quick Start function is off Auto Power OffQuick Start Audio Out Dynamic Range ControlSoftware Update Playback SettingSystem Reset Front Display/LEDIf selecting No Go to the next step On the next Communication Setup− IP address and port number of the proxy server Press c/d to select Complete, then press OptionPress a/b to select the desired input mode Operation procedure for inputting characters manuallyInput character list Press c/d to select a number/character, then press EnterUSB Memory Management Before using the USB memory devicePress a/b, select Erase or Format, then press Enter Press c/d, select Yes, and press EnterLanguage Code List Country Code ListLanguage List About Output of Next Generation Audio FormatsBasic Operation TroubleshootingPower Sound Troubleshooting PictureNetwork AppendixOther Troubleshooting NetworkTo Reset this Player Error message Possible Error Suggested Solution On-screen Error MessagesMessages Relating to BD disc and DVD disc Cannot play Disc cannot be played back withGlossary Jpeg pages 7, 8 Glossary Interlace format Region codeLetter Box LB 43 Linear PCM SoundGeneral SpecificationsPlayback Input/OutputTerms of Guarantee Sharp Corporation