Universal Electronics URC 7800 manual Trouble Shooting, Problem Solution

TROUBLE SHOOTING
Problem	Solution
Red light does not	Replace the batteries with four (4) new AAA alka-
blink when you press	line batteries.
a key?
The Cinema 7+™	Try all of the codes listed for your brand of home
does not operate	entertainment component in the “Setup Codes” sec-
your home entertain-	tion. Many setup codes may allow for partial func-
ment components or	tionality, however, only one setup code will operate
is not performing	your home entertainment component correctly.
commands properly?	Make sure that all of the components you are
	setting up can be operated with an infrared
	remote control.
Problems program-	Try the VCR set-up codes for your brand. However,
ming a TV/VCR	some combo units may require both a TV code for
combo?	volume control and a VCR code for the remaining
	functions.
VCR not recording?	As a safety feature on the Cinema 7+™ , you must
	press the REC key twice.
CH▲ / ▲and PREV	Due to RCA design (1983-1987), only the original
CH not working for	remote control will operate these functions.
your RCA TV?
Problems changing	If your original remote control required an Enter
channels?	keystroke when changing channels, press the
	ENTER key on the Cinema 7+™ after you enter the
	channel number.
The red light blinks	Make sure you are aiming your Cinema 7+™ at your
when you press a	home entertainment component and that you are
key but you receive	within 15 feet before using your remote.
no response from
your home
entertainment
component?
Cinema 7+™ not	Make sure your remote controls are nose-to-nose
learning a command	and are no more than 2 inches apart (see diagram
from your original	in step 5 on page 24).
remote control?
Tried “Search	Try the “Search Method” again after clearing out the
Method” and still did	device key as follows: Press and hold SETUP until
not find the code?	red light blinks twice, then release. Next enter 9 - 9 -
	2. Then press and release the device key to be
	cleared twice.
Sony’s Picture In	Press TV once. Press and hold SETUP until red
Picture (PIP) won’t	light blinks twice, then release. Enter 9 - 9 - 4 and
turn off?	press SETUP once. Then enter 6 - 2 - 1 and press
	PIP On/Off. The red light should blink twice. PIP
	should operate properly now.
Sharp’s Picture In	Sharp’s PIP feature requires separate PIP functions
Picture (PIP) won’t	for “on” and “off”.
work properly?	For PIP “on”, pressTV once. Press and hold SETUP
	until red light blinks twice, then release. Enter 9 - 9 - 4
	and press SETUP once. Enter 3 - 4 - 8 and press PIP
	On/Off. The red light should blink twice. PIP “on”
	should operate properly now.
	For PIP “off”, pressTV once. Press and hold
	SETUP until red light blinks twice, then release.
	Enter 9 - 9 - 4 and press SETUP once. Enter 6 - 0 - 6
	and press SETUP PIP On/Off. The red light should
	blink twice. PIP “off” should operate by pressing
	SETUP then the PIP key.

Web Site : http://www.oneforall.com

TROUBLE SHOOTING (continued)

Problem	Solution
Surround on Sony	Press RCVR once. Press and hold SETUP until red
receiver will not	light blinks twice, then release. Enter 9 - 9 - 4 and
turn on?	press SETUP once. Enter 3 - 9 - 8 and press SUR-
	ROUND. Red light should blink twice. Surround
	should operate now.
Sony receiver will	Try using the number pad on the Cinema 7+™ to
turn off but not	turn the receiver back on. For example, try pressing
back on?	0 to turn on in the CD mode, or 4 to turn on in the
	Video 1 mode. Other numeric keys will also turn the
	receiver on. If this doesn’t work, try the following:
	Press RCVR once. Press and hold SETUP until red
	light blinks twice, then release. Enter 9 - 9 - 4 and
	press SETUP once. Then enter 5 - 9 - 1 and press
	POWER. The red light should blink twice. Power
	should operate properly now.
Audio component	Audio functionality may be split between codes. For
not fully-operational?	example, Pioneer’s Tuner code 0014 works tuner
	presets, but only Amplifier code 0013 works power
	and volume. This also true for Sony’s Receiver code
	0158 and Misc. Audio code 0159.
	If some functionality is missing, try other codes to
	see if functionality resides there.
Mini-system, book-	These systems may operate using a CD or Misc.
shelf, or boombox	Audio code. If the original remote control did not
not working?	have a power key, press PL (or STOP) to turn on
	(or off) the system.

Consumer Help Line : 1-330-405-8606

E-Mail Address : HAGHelp@ueic.com

World Wide Web : http://www.oneforall.com

Web Site : http://www.oneforall.com

30 31