Hearth and Home Technologies SMART-BATT-II Setting 0F/0C Scale, Setting the Countdown Timer

Page 9

 

ON

 

78F

 

 

ROOM

 

 

:

 

 

8 00

AM

SETTING

 

 

 

BUTTON

 

FLAME

 

CP

Figure 13. Setting Button/Child Proof Lockout

Setting 0F/0C Scale

The factory setting for temperature is degrees Fahrenheit (0F). To change this setting to degrees Centigrade (0C):

1.Remove the battery cover on the back of the transmitter and locate the “setting button” at the top center of bat- tery compartment (see Figure 13).

2.Push setting button and 0F will begin flashing on the LCD screen (see Figure 12, Location #4).

3.Push the DOWN button on the transmitter to change 0F to 0C.

4.Push “setting button” on transmitter and Centigrade (0C) degree readings will display on LCD screen.

5.Repeat this process to change back to Fahrenheit (0F) reading, this time pushing the UP button. NOTE: LCD screen will return to normal state if setting button is not pushed within 15 seconds.

Setting Desired Room Temperature -

Thermo Operations

This remote control system can be thermostatically con- trolled when the transmitter is in the THERMO mode. (THERMO must be displayed on the screen). The transmit- ter will “sense” the room temperature every two minutes automatically turning the fireplace ON or OFF thermostati- cally. To set the desired room temperature:

1.Press the MODE button to place the transmitter into THERMO mode. THERMO ON or OFF will display.

2.Press the UP or DOWN button to select the desired room temperature. The highest SET temperature is 990 F (320 C). The lowest SET temperature is 450 F (60 C).

NOTE: To prevent repeated thermo-cycling of the gas appli- ance, the sensing unit in the transmitter will only activate the remote receiver when the temperature change exceeds 20 F (10 C) above or below the SET (desired) temperature.

When the transmitter is in the THERMO mode, it should be kept away from direct sources of heat such as fireplaces, incandescent lighting and direct sunlight. Leaving the trans- mitter in direct sunlight, for example, will cause it to read the room temperature higher than it actually is.

Setting the Countdown Timer

This remote control system can operate with a built-in count- down timer when the transmitter is in the ON or THERMO modes (THERMO or ON must be displayed on the LCD screen).

1.Press and release the TIMER/TIME button on the trans- mitter. The word TIMER and 0:15 flash on the screen (see Figure 12, Location #2).

2.Press the UP and DOWN button to begin advancing through each of the countdown time options. Available countdown times are 15 min, 30 min, 45 min, 1 hour, 1 hr 30 min, and each additional half hour up to nine hours.

3.To set the TIMER, press the SET button on the trans- mitter. If the system is ON, it will remain on until the “time” has expired. If the system is in the THERMO mode, it will cycle on and off as the room temperature requires until the “time” has expired.

NOTE: When the timer is used in the THERMO mode, the THERMO operation will discontinue when the “time” has expired.

Transmitter Low/Battery Indicator

An “X” outlined by a battery on the right side of the LCD screen will appear when battery power has dropped signifi- cantly. At this time, approximately two weeks of battery power remains.

Receiver Batteries

The batteries must be replace once every season. It is rec- ommended to replace at the beginning of the burn season with 4AA alkaline batteries.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Installation Precautions Introductionfccce RequirementsrequirementsCanadian Equipment Requirements Wiring Millivolt Valves Receiver Wiring InstructionsWiring Millivolt Valve with Rocker Hearth MountMillivolt with Rocker Switch and Receiver Wiring Millivolt Valve with 3-Wire AssemblyMillivolt with Receiver Wiring Intermittent Pilot Ignition IPI with Rocker SwitchRemote Intermittent Pilot Receiver Ignitor Wiring Intermittent Pilot Ignition IPI with 3-Wire Assembly Transmitter Remote Receiver Slide SwitchSetting the Clock Transmitter SettingsMatching Security Codes Operating InstructionsSetting Desired Room Temperature Thermo Operations Setting 0F/0C ScaleSetting the Countdown Timer Transmitter Low/Battery IndicatorSystem Check Transmitter Safety FeaturesTransmitter Battery Life Timer OperationGeneral Information Transmitter Wall BracketService Parts

SMART-BATT-II specifications

Hearth and Home Technologies has revolutionized the way we think about heating technology with its SMART-BATT-II system. This innovative product is designed to enhance efficiency and convenience in home heating. The SMART-BATT-II is a state-of-the-art battery backup system that ensures uninterrupted performance for your heating appliances, providing homeowners with peace of mind during power outages.

One of the standout features of the SMART-BATT-II is its advanced energy management system. This technology optimally manages power supply to the unit, allowing it to utilize energy from both the grid and backup sources. The system can intelligently switch between these power sources, ensuring that your heating appliances remain operational even when the electricity goes out. This capability is especially valuable in areas prone to outages, enabling families to maintain warmth and comfort during inclement weather.

The SMART-BATT-II utilizes high-capacity lithium-ion batteries, which are known for their durability and long life. These batteries provide enough backup power to operate heating systems for extended periods, offering an essential lifeline when traditional power sources are unavailable. The unit is equipped with smart charging technology, ensuring that the batteries recharge efficiently and extend their lifespan.

Another significant characteristic of the SMART-BATT-II is its user-friendly interface. Homeowners can easily monitor the battery status, power usage, and system performance through a simple display screen. Additionally, the system offers remote access capabilities, allowing homeowners to control and manage their heating system from anywhere via smartphone or tablet. This feature significantly enhances user convenience and facilitates better energy management.

Safety is also a priority with the SMART-BATT-II. The system includes built-in safety features such as overcharge protection and thermal management, ensuring that the unit operates safely and efficiently. Hearth and Home Technologies have also designed the SMART-BATT-II to be compact and easy to install, making it suitable for a wide range of home heating systems.

In summary, the SMART-BATT-II by Hearth and Home Technologies represents a significant advancement in home heating technology. With its robust energy management capabilities, high-capacity batteries, and user-friendly features, it provides a reliable and efficient solution for homeowners seeking consistent warmth and comfort. This innovative system is not just a backup; it is a forward-thinking solution designed for the modern home.
Top Page Image Contents