X10 Wireless Technology IR32A owner manual Sleep, Learning

Page 13

Sleep

Sleep lets you set any device to turn off a preset time from now. You can set the off time in increments of 15 minutes, up to a maximum of 90 minutes.

Press the HOME button to go to the Home Screen, then press the Side Key next to Sleep.

You can set a sleep timer for any or all of the devices that you’ve set up, i.e., any that are not grayed out.

In this example we only have a TV, Cable Box, and Satellite Receiver set up.

Below, we pressed Side Key K1 next to the TV icon once, to set a sleep timer of 15 minutes.

We pressed Side Key K2 next to the Cable Box icon twice to set a sleep timer for 30 minutes.

And we press Side Key K7 next to the Sat icon five times to set a sleep timer of 1 hour and 30 minutes.

Pressing OK takes you back to the Home screen with your sleep timers saved. The next time you select the Sleep screen you’ll see that the sleep timers have started to count down.

Make sure you leave the remote pointing at the device(s) you’ve set Sleep Timers for so it can send the Power command to the device(s) at the time(s) you’ve set.

24

X10 Macros

Learning

Tips On Learning

The following are the guidelines that will help you use this feature:

a.Some functions from some types of remotes might not be able to be learned.

b.No functions may be learned under the HOME, MODE, FAVORITE, HIS, or HERS (hard) keys.

c.Use fresh batteries for both the IR32A remote and your Original Remote.

d.Keep at least three feet away from incandescent or low- energy lights when learning. (Ambient light can influence learning a great deal.)

e.Place the original remote end-to-end with the IR32A remote so the IR transmitter (at the top) on your original remote points at the IR learning device on the bottom of the IR32A IconRemote.

f.Keep the distance between the two remotes to approximately 1 inch.

g.Line up the remotes and then press the key you want to learn. To get the correct range, press the key on the remote you are learning and you will see a “red halo” around the transmit icon at the bottom left of the screen starts to flicker. The best range for learning is when it flickers most rapidly. Move the position of the 2 remotes to achieve this. (Slightly off center may improve the best learning.) Do not change this “best distance” between the two remotes until you have learned all the required keys.

h.When Learning, you should normally not release the key being learned until the display prompts you to do so. However, some keys might be learned multiple times if you do this. If this happens just “tap” the key you want to learn, rather than press and hold it. For example, keys that you normally hold down for a while (like volume up or down) will likely require a long press when learning. Keys that you normally give a quick press (like the numbers, and channel up/down) will likely require a quick press when learning. If after learning say the channel up key, you find that it changes multiple channels when pressed once, try relearning it with a short key press.

i.If learning the first or second keys results in continuous errors then try the following:

25

Image 13
Contents IconRemote FCC Caution Safety ConsiderationsIntroduction Table of ContentsHard Key Functions Hard Key Functions, Battery Installation SetupBattery Saver Using the WizardHow to set up a TV Setting Up Your DevicesSetting Up Your Devices, Setting Up Your Favorites, Setting Up Your FavoritesSetting Up Your Remote to Send RF commands Setting Up Your Favorites, Setting Up X10 DevicesWireless DescriptionSelect Pick Device Setting Up X10 Devices,Using The Remote Setting up an LM465 Lamp Module exampleExtended Features Lamp ModuleLabeling Feature Using The Remote,Select Home/Setup/X10/More/Sleep Macro Sleep Macro StepsQuickPower Mode KeySleep Macro Steps, Favorite KeyLearning SleepLearning, Learning Main Keys Learning a Macro Main Keys Learning Main Keys,Macros Main Keys, Learning Side Keys, Learning Side KeysLearning Macros Side Keys Learning Macros, Setting up more Devices Setting up moreSetting up more, Setting up more FavoritesReordering Favorites Adding/Editing FavoritesRenaming Favorite Groups Deleting FavoritesAdvanced Settings Clearing Settings in the RemoteOptions Device CodesProgramming Combo Device Codes Advanced Settings,Punchthrough Punchthrough,X10 Home Control KidSafeAdvanced, then KidSafe Second method using a TM751 that was set up previously First method using a TM751 that was set up previouslyX10 Macros X10 Macros,Voice Dialer Security Console Audio and Video CompatibilityAt the add and X10 device! screen, press the OK key Month Limited Warranty TroubleshootingPage IR32A-3/09