Mitsubishi Electronics VS-60609 service manual Convergence Adjustment Mode

Page 21

MODELS: VS-45609 / VS-50609 / VS-55609 / VS-60609 / VS-60719 / VS-70709

D. Saving Adjustment Data

Press “ENTER” to save adjustment data in memory. The character display turns red for approximately one second in this step.

Note: If the circuit adjustment mode is terminated without pressing “ENTER”, changes in adjustment data are not saved.

E. Terminating the Circuit Adjustment Mode

Press the “MENU” button on the remote hand unit twice to terminate the adjustment mode.

Note: The circuit adjustment mode can also be terminated by turning power OFF.

7. Convergence Adjustment Mode

The Convergence mode is used to perform raster geometry correction, and convergence adjustments as specified in Adjustment Procedures 15, 17, 18, 19 and 20.

A. Convergence Mode Activation

1. Press MENU-0-1-5-9

2.When the Convergence Mode is activated, the display at the right appears on a Green Crosshatch.

B. Convergence Mode Functions

In the Convergence Mode there are three main Functions (Categories).

•Pressing “6” activates CONV MISC

•Pressing “5” activates COARSE CONV

•Pressing “4” activates FINE CONV

C. CONV MISC (Press 6)

This mode is used to preset data values controlling the Convergence Generator, and to perform the HV Regulation adjustment.

1.Use the VIDEO button to select an item.

2.Use the ADJUST buttons to change data.

Note: When Item “1 HVOL” is selected the screen goes black except for the data display. This occurs since a black screen is required when making the HV Regulation adjustment.

D. COARSE CONV (Press 5)

There are four Sub Functions in the Coarse mode, COARSE GREEN, COARSE RED, COARSE BLUE and DF.

•COARSE GREEN .... used to make Coarse Raster Geometry Adjustments.

•COARSE RED ... used to make Coarse Red Convergence Adjustments.

•COARSE BLUE ... used to make Coarse Blue Convergence Adjustments.

•DF ... used to preset data values controlling the Dynamic Beam Focus circuit drive signal.

Page 21

Image 21

Contents VZ9 ModelsMitsubishi Digital Electronics AMERICA, INC Page Contents Service Parts List Circuitry Block Diagrams Chip Parts Replacement Replacement PartsIntroduction Product Safety NoticeSafety Precautions Radiation warningLeakage current check Cabinet Disassembly Front View Front Cabinet DisassemblyRefer to Parts List for Part Numbers Rear Cabinet Disassembly Cabinet Disassembly Rear ViewPage Table a Size Length1c. VS-70709 Cabinet Separation Precedure Cabinet Separation Procedure VS-70709DiamondShield Installation Procedure DiamondShield Removal ProcedureServicing the Diamondshield Top & Bottom Molding Clips Side Molding ClipsMajor Parts Locations Chassis Removal and PCB LocationsRemoval of the CRT CRT ReplacementPage Adjustment procedures after replacing the CRTs Test Signal Electrical AdjustmentsMonoscope Signal Color Bar SignalOption Menu Setup Initial SettingsDefault Settings Description Initial SettingError Code Operational Check LED Indicator DiagnosticsError Codes AV MemoryActivating the Circuit Adjustment Mode Adjustment FunctionsSelection of adjustment Functions Adjustment Items Changing DataConvergence Adjustment Mode Sub Functions Fine Conv PressCursor Cursor CoordinatesDisplay Saving Data and Exiting the Convergence ModeAdjustment Items List Audio FunctionPIP Function HR Function Convergence Mode ItemsConv Misc Conv GreenConv Blue Conv REDDF Function VkeyPage Audio Circuit Purpose Service ModeInput Level Audio Function Abbrev DataDynamic Focus Symptom High Voltage Control SymptomConvergence Mode High Voltage Circuit PurposeFocus Verification Lens Focus Symptom Blurred pictureMENU-0-1-5-9 Color PressAbbr Data Service Mode CRT Cutoff SymptomCRT Circuit Purpose CRT CurrentService Mode Activate …….. MENU-0-1-5-7 Low Color TemperatureColor and Tint Symptom PIP Circuit PurposePIP Insert Picture 13. Cb, Cr Offset Symptom Cb, Cr Circuit PurposeOn-screen display is not positioned correctly Abbr Data Height and Vert. Linearity Symptom Deflection Circuit PurposeConvergence Circuit Purpose Convergence Circuit Purpose Coarse Convergence Color edging at the top, bottom and sides of the picture Fine Convergence SymptomReplacement Chip Parts Removal Resistors, Capacitors, etcChip Parts Removal Transistors Parts Ordering Critical and Warranty Parts DesignationParts Tolerance Codes Model AbbreviationsQuick Reference for Common Replacement Parts Remote ControlCRT Assemblies High Voltage / Deflection ComponentsIntegrated Circuits TubesTransistors DiodesCOIL-CHOKE ZTS6620 CoilsTransformers Variable ResistorsResistors Carbon 1/4W 10K-J R521R529 Fuse 1/2W 0.82-JCapacitors & Trimmers Composition 1/2W 4.7M-KComposition 1/2W 1M-K CER-CHIP SL50V 470P-J CER-CHIP CH50V 82P-JCER-CHIP CH50V 47P-J CER-CHIP CH50V 68P-JC554 C552PLA-PP 200V 0.47M-J C568Poly 250VAC 0.1M-M C902 C901Poly 250VAC 0.1M-M C903 CER 250VAC 1000P-M C904Accessories MiscellaneousPrinted Circuit Boards Screen Parts Screen Assembly Circuitry Block Diagrams Power SupplyVIDEO/COLOR Signal Path Sound Circuit Deflection Protect Circuit Convergence Circuitry Control Circuit Page Page Page Page Page Page Page Page Page Page Page