Philips DCR 9000 First installation, Installation settings, Channel search, Search failure

Page 20

EN

68

8 First installation

You have inserted the batteries supplied in your remote control.

Your receiver is connected to the cable wall socket,TV set and other equipment according to one of the diagrams in chapter 7.

-Switch on your TV set and select the appropriate HDMI input (refer to your TV set user manual).

-Plug the receiver’s power supply cord into the mains. The receiver display indicates

, then .

-Press V-Outputonce, then check the receiver display indication:

If is displayed, check that the welcome screen displays on your TV screen.

• if is displayed instead, successively press V-Outputuntil the source selected matches your connections as described in paragraph 7.1 and the welcome screen appears on your TV screen.

-Press P+ then P-.Wait for a few seconds for the First Installation screen to appear.

8.1 Installation settings

-Select your favourite language.

-Check for adequate signal strength and quality.

-Press OK to start searching for channels. The Installation screen appears.

-Proceed to paragraph 8.2.

If you press EXIT during the scanning process, you interrupt the scanning and

go back to the previous screen. In this case, none of the channels found are stored.

8.2 Channel search

Once the scan has been successfully completed, a completion message is displayed. - Press OK.

A new screen appears, with a message indicating that a search for new, upgraded software is in progress:

-Either wait for software detection, and then proceed as indicating on screen. It is recommanded to accept software so as to keep your receiver up-to-date. At the end

of the first installation, the receiver tunes to the first channel in the main TV list.

-Or press EXIT to stop searching for new software and tune the receiver to the first channel in the main TV list.

8.3 Search failure

In case of channel search failure, a message is displayed.

- Press EXIT to go back to the First Installation screen.

Before starting a new scan

The following checks are recommended to recover adequate signal quality and strength:

Check the RF coaxial cable.

Then check the RF coaxial cable connection to your receiver (see chapter 7).

-When the signal strength and quality is adequate, press OK to launch a new search.

If the failure message appears again, refer to chapter 17 to find out the reason for failure.

For a proper diagnosis and installation check, call your installer.

Image 20
Contents DE Benutzerhandbuch Foreword Contents Settings Advanced settingsMenu system Premiere MenuUnpacking Quick installation TV setInsert the two batteries supplied in your remote control Meaning of symbols So do not dispose of them with your normal household wasteSafety instructions Product description EN 4.1 Front panelDescription of segment display messages Front panel displayPictograms Rear panel U I OInserting your Smartcard Using your remote control when the STB mode is selected RED, GREEN,YELLOW BlueConnecting your digital receiver ConnectionsYour TV set is Hdtv capable HD-Ready label Digital connection to TV via Hdmi lead supplied recommendedTV set Analogue connection to TV via YPbPr lead not supplied Connection to a recorderYour TV set is only Sdtv capable Your video projector is only Sdtv capable Connecting to a video projector to watch Digital TVDigital audio connections First installation Installation settingsChannel search Search failureSwitching your receiver on Or to LOW Power or STAND-BY Using number keys of the remote controlUsing channel lists Day-to-day operationBanner Volume control / +PIN code Set or delete recording timers Electronic Programme Guide EPGChecking or changing the video output resolution setting Setting a timer in the EPGCancelling an active timer Viewing teletextPremiere features Premiere MultifeedEXT1 Scart Premiere MenuEN 11.1 Menu tree Changing settings Cancelling/storing changesMenu navigation BasicsSoftware Upgrade Factory SettingsPIN Code Change SmartcardScan DisplayDolby Digital out of the digital audio output Wake upSettings Timer ManagerTo delete an existing timer To set or edit a timerList Organization List EditingChannel Pool Remove/Reorder ChannelsAdvanced settings TV SettingsCase1 Broadcast isSystem Settings Time SettingsTV is 169 Any setting Case2Settings For ParentsDisplay options Language optionsSoftware Upgrade Software upgrade messagesDecoder Status System InformationPage Advanced settings Restoring factory settingsChanging the remote control setting Connecting your equipment for Video/DVD Recorder ControlDigital receiver and VCR or DVD recorder settings Recording using the Video/DVD Recorder Control featureMode selection selecting the device you want to control Volume and mute control assignmentDefault volume and mute control assignment Changing the volume and mute control assignmentSTB Battery changeDisclaimer Using the remote control when the TV mode is selected Controlling your TV,Video Recorder, DVD and amplifierUsing the remote control when the VCR mode is selected TV/VCRUsing the remote control when the DVD mode is selected Preset Up/Down Tuning Down/Up Glossary Troubleshooting Symptom Cause RemedySymptom Cause RemedyTechnical specifications 73/23/EEC 93/68/EEC 89/336/EECPage Code List für verschieden Marken/Brand code list AGB ARTASA BPL100 101 102 103 104 AVPGPX KEC105 106 107 108 XMS 109TSM 110 111 3111 176
Related manuals
Manual 50 pages 30.17 Kb