Philips DCR 9000 Decoder Status, System Information, Software Upgrade, Software upgrade messages

Page 35

13.5.4 Factory Settings

This screen is used to reset your receiver back to the factory default condition.

-When prompted, press the red colour key to confirm.

-Alternatively, press EXIT to exit the screen without modifying the receiver settings.

If you reset your receiver to factory settings, you lose all the settings you stored

previously.

13.5.5 Decoder Status

The Decoder Status sub menu menu includes the following items: o System Information

o Decoder Upgrade

13.5.5.1 System Information

This screen is used to display information about your receiver, including the Premiere Serial Number and software version.

You can also access this screen via the Premiere menu.

13.5.5.2 Software Upgrade

This item is used for software upgrades. Select it to check the current software version as well as launch a search for new software. After a while, the Software Upgrade screen indicates whether new software is available.

-Press EXIT to exit the screen in case no new software is available. In case software is available, you are offered three options:

-Press the green colour key to choose to upgrade your receiver immediately, and then press OK to launch new software installation.

-Or press the yellow colour key to choose to upgrade your receiver later, and then press OK to confirm your choice. New software installation takes place as soon as you set your receiver to standby.

-Or press the red colour key to refuse to upgrade your receiver and return to the Decoder status sub menu.

After successful software installation, a confirmation message is displayed. In case of installation failure, a failure message is displayed, indicating that a new installation attempt will take place as soon as you set your receiver to standby. In both cases, press OK to exit the upgrade process.

You can also launch a search for new software from the screen described above using

the red colour key.

Software upgrade messages

Software update starting

Software loading progress: from 0 to 100%

Software storing progress: from 0 to 100%

Do not unplug the receiver before the end of the storing operation.

13.6 Channel Search

This item is used to search for new channels.

It is recommended not to change the predefined settings:

Start frequency: 114 MHz

Stop frequency: 858 MHz

Constellation: Auto

Band width: 8000 KHz

EN

83

Image 35
Contents DE Benutzerhandbuch Foreword Contents Premiere Menu SettingsAdvanced settings Menu systemUnpacking TV set Quick installationInsert the two batteries supplied in your remote control So do not dispose of them with your normal household waste Meaning of symbolsSafety instructions EN 4.1 Front panel Product descriptionDescription of segment display messages Front panel displayPictograms U I O Rear panelInserting your Smartcard RED, GREEN,YELLOW Blue Using your remote control when the STB mode is selectedDigital connection to TV via Hdmi lead supplied recommended Connecting your digital receiverConnections Your TV set is Hdtv capable HD-Ready labelTV set Connection to a recorder Analogue connection to TV via YPbPr lead not suppliedYour TV set is only Sdtv capable Your video projector is only Sdtv capable Connecting to a video projector to watch Digital TVDigital audio connections Search failure First installationInstallation settings Channel searchDay-to-day operation Switching your receiver on Or to LOW Power or STAND-BYUsing number keys of the remote control Using channel listsBanner Volume control / +PIN code Electronic Programme Guide EPG Set or delete recording timersViewing teletext Checking or changing the video output resolution settingSetting a timer in the EPG Cancelling an active timerPremiere Multifeed Premiere featuresEXT1 Scart Premiere MenuEN 11.1 Menu tree Basics Changing settingsCancelling/storing changes Menu navigationSmartcard Software UpgradeFactory Settings PIN Code ChangeWake up ScanDisplay Dolby Digital out of the digital audio outputTo set or edit a timer SettingsTimer Manager To delete an existing timerRemove/Reorder Channels List OrganizationList Editing Channel PoolBroadcast is Advanced settingsTV Settings Case1Case2 System SettingsTime Settings TV is 169 Any settingLanguage options SettingsFor Parents Display optionsSystem Information Software UpgradeSoftware upgrade messages Decoder StatusPage Connecting your equipment for Video/DVD Recorder Control Advanced settingsRestoring factory settings Changing the remote control settingRecording using the Video/DVD Recorder Control feature Digital receiver and VCR or DVD recorder settingsChanging the volume and mute control assignment Mode selection selecting the device you want to controlVolume and mute control assignment Default volume and mute control assignmentSTB Battery changeDisclaimer Controlling your TV,Video Recorder, DVD and amplifier Using the remote control when the TV mode is selectedTV/VCR Using the remote control when the VCR mode is selectedUsing the remote control when the DVD mode is selected Preset Up/Down Tuning Down/Up Glossary Symptom Cause Remedy TroubleshootingRemedy Symptom Cause73/23/EEC 93/68/EEC 89/336/EEC Technical specificationsPage Code List für verschieden Marken/Brand code list BPL AGBART ASA100 101 102 103 KEC 104AVP GPX105 106 107 108 XMS 109TSM 110 111 3111 176
Related manuals
Manual 50 pages 30.17 Kb