Philips PH5DSS manual Code Search, Code Identification Feature, Code Search by Brand

Page 6

Code Search, cont.

Code Identification Feature

Most users will store VCR codes under the VCR button, Cable codes under CABLE, etc. If (for example) you want to store a VCR code under CABLE, first follow the procedure for Direct Code Entry (previous page) and press CABLE in step 2 of Direct Code Entry, then enter ANY VCR code in step 3 of Direct Code Entry. Then follow the steps above for Code Search (or Brand Search, below). Note: If the device does not have a CHANNEL UP button, use PLAY (VCR only) or POWER instead. Code Search starts from the currently stored 4 digit number under that mode.

Code Search by Brand

Lets you search for a code for a specific Brand within the Code Library for a particular manufacturer.

1.Turn on the device (TV, VCR, etc.) to be controlled.

2.Press and hold the CODE SEARCH button until the red indicator remains on, then release CODE SEARCH button.

3.Press and quickly release the desired mode button (TV, VCR, etc.). The red indicator blinks off once.

4.Press and release the numeric button (0-9) corresponding to desired Manufacturer (see table on code list sheet). The red indicator blinks off once. Note, pressing “0” performs a full library search same as normal Code Search Method on previous page.

5.Press the CHANNEL UP button ((or POWER or PLAY (VCR only)) repeatedly until the device to be controlled changes channel. The red indicator blinks off with each button press. If you accidentally overshoot the code required, press the CHANNEL DOWN button to backtrack through the library until the device changes channel. Pressing CHANNEL UP changes direction to forward again.

6.Press and release MUTE to install the code.

Brand Search Method entry is now complete.

Note: When all codes under a Brand have been searched the red indicator flashes rapidly for 3 seconds.

The Code Identification Feature allows you to identify the 4 digit library code stored under your device key. For example, if you want to find out what 4 digit code is stored under your TV device key, follow the six steps below:

1.Press and hold the CODE SEARCH button until the red indicator stays on. Release the CODE SEARCH button.

2.Press and release the desired mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.

3.Press and release the CODE SEARCH button. The red indicator blinks off.

4.To find the first digit for the code stored under the mode key pressed in step 2, press each numeric key from 0-9in turn. When the red indicator blinks off the number you pressed is the first digit for the code you are searching for.

5.To find the second digit, repeat step 4, this time when the red indicator blinks off this is the second digit.

6.Repeat step 4 to find the third and fourth digits.

10

11

Page 5 Page 7
Image 6
Page 5 Page 7
Contents PH5DSS Table of Contents Introduction Button Functions Button Functions, TV, SAT, DVD,CBL/AUX, VCR Selects product to beSAT/DTV Receiver Functions DVD Functions labeled in blue/blackDVR Functions Setup Direct Code EntryCode Search Code Search, Code Identification Feature Code Search by BrandSetup, Programming Combo Device CodesSetting ALLVolume/Mute Control to any one Mode Code LearningIR Transmitter Finder Feature Tips On Learning,To Clear all Learned Commands under a mode Learning CommandsClearing Commands Master Clear To Clear all Learned Commands under all modesMacros Macros,Remote does not operate some features of your product TroubleshootingLimited Lifetime Warranty Red Indicator blinks after you program a product codeÍndice IntroducciónFunciones de botones Funciones de botones, TV, SAT, DVD,CBL/AUX, VCR Selecciona el equipo queFunciones DVR Funciones de Satélite/DTVFunciones de DVD rotuladas en azul/negro Entrada/TV/SATPreparación Preparación,Búsqueda de Códigos por Marcas Función de Identificación de CódigosControl de volumen/silencio y traspaso Función de traspaso de VCR/DVD/DVRPreparación, Transferencia de códigos Consejos Para el AprendizajeConsejos Para el Aprendizaje, Aprendizaje de Comandos Despejando Comandos Cómo programar una macro Notas sobre las macrosCómo borrar una macro El Control Remoto no Opera su Producto El Control Remoto no Opera Algunas Funciones de su AparatoTable des matières INPUT/TV/SATFonctions des touches, suite Fonctions DVD en bleu/noir Fonctions DVRInstallation des piles ConfigurationConfiguration, suite Économiseur de pilesRecherche de code par marque Fonction d’identification des codesCommande Volume/Mute et fonction d’accès direct Accès direct aux modes VCR/DVD/DVRConfiguration, suite Apprentissage de codes Conseils Sur L’ApprentissageConseils Sur L’Apprentissage, suite Commandes D’Enregistrement Suppression des commandesPour Effacer Toutes Les Commandes Enregistrees Sous Un Mode Pour enregistrer une macro Macros, suitePour supprimer une macro Dépannage Garantie a vie limitéeLe témoin clignote une fois le code programmé Trilingual Back Cover Art
Top Page Image Contents