Philips TP3684C1 manual Setting the Remote Control to Operate Accessory Devices

Page 36

SETTING THE REMOTE CONTROL TO OPERATE ACCESSORY DEVICES
our remote control is set to
Ywork your TV and many
infrared (IR) remote control
VCRs, Cable Boxes, Satellite
Systems, DBS, DVD, etc.
However, an easy onetime step
may be necessary before the				SLEEP
remote will work your accessory	1
device.
Try this initial check to see if		TV		AV		ON/OFF	POSITION
going on to the following section
is necessary.
BEGIN		VCR		SWAP		SOURCE
Place the TV/VCR/ACC	VCR						UP
Place the TV/VCR/ACC	VCR
Mode Switch in the proper posi-		ACC
tion.		ACC
tion.
Point the remote control at
the device and press the POWER
button.
Does the remote turn the							2
device ON?				POWER
device ON?	Satellite Receiver	SLEEP			FREEZE
				POSITION
		TV	AV	ON/OFF	PIPCH	DN
If YES, stop and try other func-		TV		SOURCE	UP	DN
				AP
				SW
			VCR
				ACC
tion buttons on the remote. If						T
tion buttons on the remote. If						SMAR
they also work the device, then					T	PICTURE
					SMAR	PICTURE
						SURF
					SOUND
						MENU
the remote is ready and no fur-							CH
ther steps are needed.							CH
	Cable Converter					VOL	MUTE	A/CH
							ATUS CLOCK
						CC	ST
							TV/VCR
							EXIT	TI
If NO, continue...								MUL
							VCR	MEDIA
							RECORD	INCREDIBLE
								STEREO

First look up a THREE-DIGIT

remote control number for your

brand of Device before going through the simple steps on the following page.

Find your Three-Digit Code on pages 39-40.

SMART HELP

Remember, if more than one number is listed, you may

have to try more than one code in order to locate your Device’s remote code.

36

Image 36

Contents TP3684C1 Warranty Verification Safety Instructions Read before operating equipment Table of Contents Features Cable/AntennaAdjusting the TV Picture Buttons to adjust the selected controlPress the STATUS/EXIT button To remove the menu from the screenSetting the TV’S Clock Timer controlsPress the Numbered buttons Cursor UP or CursorActivating the TV’S on Timer Control Timer controlPress the Menu button on Remote to show the on-screen menuSelecting the TV’S on Timer Channel Setting the TV’S on Timer Start Time To highlight the Start TimeTo enter the desired start up time Press the STATUS/EXIT but- ton to remove the menu fromTurning on the on Timer Display Button three times to select the Features menuPress the Cursor Down Understanding Smartlock Movie RatingsUsing Smartlock Setting UP the Access Code Enter current access codeDown to highlight SmartLock controlUsing Smartlock Blocking Channels Press the Channel + orThis stops the viewing of VCR, DVD, etc Select blockUsing Smartlock Movie Rating Press the Cursor Right Button to access the movie ratingsBe highlighted Button to select Movie RatingUsing Smartlock TV Rating Appear within the menuButton to select TV Rating Using Smartlock Blocking OptionsUsing Smartlock Block Unrated Button or the CursorLeft button to set Block Unrated to on orUsing Smartlock no Rating Press the Menu button on the remote to show the on-screenMenu Left button to set noReviewing the Smartlock Settings Example Blocking is set to OFFViewing Blocked Programming XxxxTurn the NR feature on or OFF Turning on the Noise Reduction ControlTo highlight the NR control Button again to highlight the NR option areaTurn the Contrast + feature on or OFF Turning on the Contrast + ControlButton again to highlight the Contrast + option area Using the Closed Caption Control Select the mode you wantButton to highlight the Closed CAP control Button again to highlightUsing the Sleep Timer Control Good BYE SleepAdjusting the TREBLE, BASS, and Balance Sound Controls Button twice to select the Sound menuSetting the TV for Stereo and SAP Programs Remember, if stereo is not presentOn a selected show and the TV is Placed in the Stereo mode, the sound comUsing the Incredible Stereo Control Using the Volume BAR ControlSetting the Audio OUT Control Button repeatedly to selectUse the Cursor Left or Right buttons to set Audio OUT to Variable orUsing the TV Speaker Control and Audio Output Jacks Connect the Right and LeftPress the Cursor Down button to select the Speakers Use the Cursor Right or Cursor Left buttonsUsing the AUDIO/VIDEO Input Jacks Connect the Video yellowUsing the AUDIO/VIDEO Input Jacks CONT’D Connect the S-VIDEOTurn the VCR or Digital Press the Smart Picture Button repeatedly to select eitherUsing the Smartsound Control Press the Smart Sound butPress the Channel + or Press the Surf button onRead, the Surf List is EMPTY, Press to addSetting the Remote Control to Operate Accessory Devices Going on to the following section Is necessaryPlace the TV/VCR/ACC Press the VCR RecordPress the Smart Sound Enter the THREE-DIGITTurn on the device by press- ing the Power button on Mode Switch in the proper posi TionDevice you are attempting to pro- gram Remote Control Direct Entry Codes Remote VCR Code noRemote Dvdcode no Using the REMOTE’S VCR Buttons Connect the Video OUT Also connect the Audio OUTRight and Left jacks from Move to the next page afterTurn the TV and VCR or Press the PIP ON/OFF butPress the PIP Source but AV 1, AV 2, SVID-R for pictureUsing the PIP PICTURE-IN-PICTURE Feature Adjusting the PIP Color and Tint Adjust the Color and Tint bars to the desired levelsButton to select the PIP menu Remember, althoughFirst use an optional signal More PIP Picture -IN -PICTURE ConnectionsConnect the Cable OUT on Connect the Video OUT jackFirst connect the original cable Connect the ANT OUT jack onConnect the yellow Video Connect a second yellow VideoTV Displays Wrong Channel or No Channels Above Tips if Something Isnt WorkingGlossary to Television Terms IndexPhilips Consumer Electronics Company Texas Limited Warranty