Philips TP3684C1 manual Place the TV/VCR/ACC, Press the VCR Record, Press the Smart Sound

Page 37

SETTING THE REMOTE CONTROL TO OPERATE ACCESSORY DEVICES

Direct Access Method

ow that you have looked up

Nthe three-digit Remote Code

Number for your brand of device,

POWER

you are ready to follow the five

1

SLEEP

simple steps below.

Please read through steps 1-5

TV

AV

ON/OFF

POSITION

FREEZE

before beginning.

BEGIN

VCR

SWAP

SOURCE

PIP CH

4

UP

DN

Place the TV/VCR/ACC

ACC

Mode Switch in the proper posi-

tion.

Press the VCR RECORD

3

button on the remote control and

VCR

release.

SMART

SMART

Press the SMART SOUND

button on the remote within 30

SOUND

PICTURE

seconds, then release.

Satellite Receiver

MENU

SURF

Enter the THREE-DIGIT

or DBS, DVD

REMOTE CODE NUMBER

for your desired device. The

remote is now ready to send

commands to the unit.

Point the remote at the

Cable Converter

VOL

CH

Device. Press the POWER button

MUTE

on the remote to turn the unit

CC

STATUS

CLOCK

ON.

2

EXIT

TV/VCR

SMART HELP

5

VCR

MULTI

Remember, if this doesn’t

SLEEP

RECORD

INCREDIBLE

MEDIA

POWER

TV AV

ON/OFF

work the first time, repeat steps

POSITION

FREEZE

VCR SWAP

SOURCE

PIP

ACC

UP CH

DN

STEREO

1-5 using the same remote code num-

ber.

SMART

SOUND

SMART

After a second try and the remote

MENU

PICTURE

SURF

does not operate your device, see if

VOL

CH

there is another three-digit code num-

MUTE

CC

STATUS

CLOCK

A/CH

EXIT

TV/VCR

ber (pages 39-40) listed for your

VCR

MULTI

RECORD

device. Repeat the steps above using

INCREDIBLE

MEDIA

STEREO

the new number.

If, after repeated attempts, the remote

does not work your device, try the

SEARCH METHOD on page 38.

Some Cable Converters can not be

turned ON by a remote control.

37

Image 37

Contents TP3684C1 Warranty Verification Safety Instructions Read before operating equipment Table of Contents Cable/Antenna FeaturesButtons to adjust the selected control Adjusting the TV PicturePress the STATUS/EXIT button To remove the menu from the screenTimer controls Setting the TV’S ClockPress the Numbered buttons Cursor UP or CursorTimer control Activating the TV’S on Timer ControlPress the Menu button on Remote to show the on-screen menuSelecting the TV’S on Timer Channel To highlight the Start Time Setting the TV’S on Timer Start TimeTo enter the desired start up time Press the STATUS/EXIT but- ton to remove the menu fromButton three times to select the Features menu Turning on the on Timer DisplayPress the Cursor Down Movie Ratings Understanding SmartlockEnter current access code Using Smartlock Setting UP the Access CodeDown to highlight SmartLock controlPress the Channel + or Using Smartlock Blocking ChannelsThis stops the viewing of VCR, DVD, etc Select blockPress the Cursor Right Button to access the movie ratings Using Smartlock Movie RatingBe highlighted Button to select Movie RatingAppear within the menu Using Smartlock TV RatingButton to select TV Rating Options Using Smartlock BlockingButton or the Cursor Using Smartlock Block UnratedLeft button to set Block Unrated to on orPress the Menu button on the remote to show the on-screen Using Smartlock no RatingMenu Left button to set noExample Blocking is set to OFF Reviewing the Smartlock SettingsXxxx Viewing Blocked ProgrammingTurning on the Noise Reduction Control Turn the NR feature on or OFFTo highlight the NR control Button again to highlight the NR option areaTurning on the Contrast + Control Turn the Contrast + feature on or OFFButton again to highlight the Contrast + option area Select the mode you want Using the Closed Caption ControlButton to highlight the Closed CAP control Button again to highlightGood BYE Sleep Using the Sleep Timer ControlButton twice to select the Sound menu Adjusting the TREBLE, BASS, and Balance Sound ControlsRemember, if stereo is not present Setting the TV for Stereo and SAP ProgramsOn a selected show and the TV is Placed in the Stereo mode, the sound comUsing the Volume BAR Control Using the Incredible Stereo ControlButton repeatedly to select Setting the Audio OUT ControlUse the Cursor Left or Right buttons to set Audio OUT to Variable orConnect the Right and Left Using the TV Speaker Control and Audio Output JacksPress the Cursor Down button to select the Speakers Use the Cursor Right or Cursor Left buttonsConnect the Video yellow Using the AUDIO/VIDEO Input JacksConnect the S-VIDEO Using the AUDIO/VIDEO Input Jacks CONT’DTurn the VCR or Digital Button repeatedly to select either Press the Smart PicturePress the Smart Sound but Using the Smartsound ControlPress the Surf button on Press the Channel + orRead, the Surf List is EMPTY, Press to addGoing on to the following section Is necessary Setting the Remote Control to Operate Accessory DevicesPress the VCR Record Place the TV/VCR/ACCPress the Smart Sound Enter the THREE-DIGITMode Switch in the proper posi Tion Turn on the device by press- ing the Power button onDevice you are attempting to pro- gram Remote VCR Code no Remote Control Direct Entry CodesRemote Dvdcode no Using the REMOTE’S VCR Buttons Also connect the Audio OUT Connect the Video OUTRight and Left jacks from Move to the next page afterPress the PIP ON/OFF but Turn the TV and VCR orPress the PIP Source but AV 1, AV 2, SVID-R for pictureUsing the PIP PICTURE-IN-PICTURE Feature Adjust the Color and Tint bars to the desired levels Adjusting the PIP Color and TintButton to select the PIP menu Remember, althoughMore PIP Picture -IN -PICTURE Connections First use an optional signalConnect the Cable OUT on Connect the Video OUT jackConnect the ANT OUT jack on First connect the original cableConnect the yellow Video Connect a second yellow VideoTips if Something Isnt Working TV Displays Wrong Channel or No Channels AboveIndex Glossary to Television TermsPhilips Consumer Electronics Company Texas Limited Warranty