Philips TP3684C1 manual Turn on the device by press- ing the Power button on

Page 38

SETTING THE REMOTE CONTROL TO OPERATE ACCESSORY DEVICES

Search Method

Your TV remote can be set to work various accessory

devices such as VCRs, Cable Boxes, Satellite Receivers, DBS, DVD, etc. by using the search method.

If the Direct Access method shown on page 37 did not set your remote to work your acces- sory device, follow the easy steps listed below.

Please read steps 1-4 before beginning.

BEGIN

Turn ON the device by press- ing the POWER button on the

device you are attempting to pro- gram.

Place the TV/VCR/ACC

Mode Switch in the proper posi-

tion.

Press and hold the VCR RECORD and the SMART SOUND buttons simultaneous- ly.

The device will begin to change channels after the remote identifies the correct code. When the channels start to change, release the VCR RECORD and SMART SOUND buttons. The remote should be ready to oper- ate the device.

SMART HELP

This method can take up to two minutes to perform.

Don’t let the device change more than five channels after the remote identifies the code. If you do, the remote may pass up the right code; another two minute search cycle will have to be repeated.

If no channel change happens within two minutes, repeat steps 1-4. Should a channel change still not occur, the remote will not work the desired device.

Satellite Receiver,

DBS, DVD,

or similar device

Cable Converter		070809 06			07
1					07
1					0809
			06	0708	0809
VCR				09
				09
2	SLEEP			POWER	4
2	AV	ON/OFF	POSITION FREEZE
TV	AV	ON/OFF	POSITION FREEZE
VCR	SWAP	SOURCE		PIP CH
			UP	DN
ACC
	SMART			SMART
	SOUND			PICTURE
	MENU			SURF
3
	VOL			CH
		MUTE

CC STATUS CLOCK A/CH

EXIT TV/VCR

VCR

MULTI

RECORDMEDIA

INCREDIBLE

3

38

Image 38

Contents TP3684C1 Warranty Verification Safety Instructions Read before operating equipment Table of Contents Features Cable/AntennaPress the STATUS/EXIT button Adjusting the TV PictureButtons to adjust the selected control To remove the menu from the screenPress the Numbered buttons Setting the TV’S ClockTimer controls Cursor UP or CursorPress the Menu button on Activating the TV’S on Timer ControlTimer control Remote to show the on-screen menuSelecting the TV’S on Timer Channel To enter the desired start up time Setting the TV’S on Timer Start TimeTo highlight the Start Time Press the STATUS/EXIT but- ton to remove the menu fromPress the Cursor Down Turning on the on Timer DisplayButton three times to select the Features menu Understanding Smartlock Movie RatingsDown to highlight Using Smartlock Setting UP the Access CodeEnter current access code SmartLock controlThis stops the viewing of VCR, DVD, etc Using Smartlock Blocking ChannelsPress the Channel + or Select blockBe highlighted Using Smartlock Movie RatingPress the Cursor Right Button to access the movie ratings Button to select Movie RatingButton to select TV Rating Using Smartlock TV RatingAppear within the menu Using Smartlock Blocking OptionsLeft button to set Using Smartlock Block UnratedButton or the Cursor Block Unrated to on orMenu Using Smartlock no RatingPress the Menu button on the remote to show the on-screen Left button to set noReviewing the Smartlock Settings Example Blocking is set to OFFViewing Blocked Programming XxxxTo highlight the NR control Turn the NR feature on or OFFTurning on the Noise Reduction Control Button again to highlight the NR option areaButton again to highlight the Contrast + option area Turn the Contrast + feature on or OFFTurning on the Contrast + Control Button to highlight the Closed CAP control Using the Closed Caption ControlSelect the mode you want Button again to highlightUsing the Sleep Timer Control Good BYE SleepAdjusting the TREBLE, BASS, and Balance Sound Controls Button twice to select the Sound menuOn a selected show and the TV is Setting the TV for Stereo and SAP ProgramsRemember, if stereo is not present Placed in the Stereo mode, the sound comUsing the Incredible Stereo Control Using the Volume BAR ControlUse the Cursor Left or Right buttons to set Setting the Audio OUT ControlButton repeatedly to select Audio OUT to Variable orPress the Cursor Down button to select the Speakers Using the TV Speaker Control and Audio Output JacksConnect the Right and Left Use the Cursor Right or Cursor Left buttonsUsing the AUDIO/VIDEO Input Jacks Connect the Video yellowTurn the VCR or Digital Using the AUDIO/VIDEO Input Jacks CONT’DConnect the S-VIDEO Press the Smart Picture Button repeatedly to select eitherUsing the Smartsound Control Press the Smart Sound butRead, the Surf List is Press the Channel + orPress the Surf button on EMPTY, Press to addSetting the Remote Control to Operate Accessory Devices Going on to the following section Is necessaryPress the Smart Sound Place the TV/VCR/ACCPress the VCR Record Enter the THREE-DIGITDevice you are attempting to pro- gram Turn on the device by press- ing the Power button onMode Switch in the proper posi Tion Remote Control Direct Entry Codes Remote VCR Code noRemote Dvdcode no Using the REMOTE’S VCR Buttons Right and Left jacks from Connect the Video OUTAlso connect the Audio OUT Move to the next page afterPress the PIP Source but Turn the TV and VCR orPress the PIP ON/OFF but AV 1, AV 2, SVID-R for pictureUsing the PIP PICTURE-IN-PICTURE Feature Button to select the PIP menu Adjusting the PIP Color and TintAdjust the Color and Tint bars to the desired levels Remember, althoughConnect the Cable OUT on First use an optional signalMore PIP Picture -IN -PICTURE Connections Connect the Video OUT jackConnect the yellow Video First connect the original cableConnect the ANT OUT jack on Connect a second yellow VideoTV Displays Wrong Channel or No Channels Above Tips if Something Isnt WorkingGlossary to Television Terms IndexPhilips Consumer Electronics Company Texas Limited Warranty