Philips 27RF 70S manual Important Safety Instructions

Page 3

IMPORTANT SAFETY INSTRUCTIONS

Read before operating equipment

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this apparatus near water.

6.Clean only with a dry cloth.

7.Do not block any of the ventilation openings. Install in accordance with the manufacturers instructions.

8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9.Do not defeat the safety purpose of the polarized or ground- ing-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and third grounding prong. The wide blade or third prong are provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11.Only use attachments/accessories specified by the manu- facturer.

12.Use only with a cart, stand, tripod, bracket, or table

specified by the manufacturer, or sold with the app-

aratus. When a cart is used, use caution when moving the cart/apparatus combination to avoid

injury from tip-over.

13.Unplug this apparatus during lightning storms or when unused for long periods of time.

14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15.This product may contain lead and mercury. Disposal of these materials may be regulated due to environmental con- siderations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance: www.eiae.org

16.Damage Requiring Service - The appliance should be serviced by qualified service personnel when:

A.The power supply cord or the plug has been damaged; or

B.Objects have fallen, or liquid has been spilled into the appliance; or

C.The appliance has been exposed to rain; or

D.The appliance does not appear to operate normally or exhibits a marked change in performance; or

E.The appliance has been dropped, or the enclosure damaged.

17.Tilt/Stability - All televisions must comply with recommend- ed international global safety standards for tilt and stability properties of its cabinet design.

• Do not compromise these design standards by applying excessive pull force to the front, or top, of the cabinet which could ultimately overturn the product.

• Also, do not endanger yourself, or children, by placing electronic equipment/toys on the top of the cabinet. Such items could unsuspectingly fall from the top of the set and cause product damage and/or personal injury.

18.Wall or Ceiling Mounting - The appliance should be mounted to a wall or ceiling only as recommended by the manufacturer.

19.Power Lines - An outdoor antenna should be located away from power lines.

20.Outdoor Antenna Grounding - If an outside antenna is connected to the receiver, be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges.

Section 810 of the National Electric Code, ANSI/NFPA No. 70-1984, provides information with respect to proper grounding of the mats and supporting structure grounding of the lead-in wire to an antenna discharge unit, size of grounding connectors, location of antenna-discharge unit, connection to grounding electrodes and requirements for the grounding electrode. See Figure below.

21Object and Liquid Entry - Care should be taken so that objects do not fall and liquids are not spilled into the enclo- sure through openings.

Note to the CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

Example of Antenna Grounding

as per NEC - National Electric Code

GROUND CLAMP

ELECTRIC SERVICE EQUIPMENT

ANTENNA LEAD IN WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents For fast help, call us first Warranty Verification Important Safety Instructions Table of Contents Standard Broadcast VHF/UHF or Cable TV Catv channel capabil FeaturesAdjusting the Picture Turning on the Dynamic Noise Reduction Control Turning on the Imagemax ControlPress the STATUS/EXIT button Using the Closed Captioning Control Press the Cursor Right button and the menu will shift toPress the STATUS/EXIT but- ton to remove the menu from Press the STATUS/EXIT but Selecting the Screen Format SizePress the Cursor Down Press the Cursor RightPress the STATUS/EXIT but Activating the Blue Mute ControlPress the Menu button on Press the Cursor RightSleep OFF Using the Sleep TimerTimer Setting the Clock Press the Cursor UP or CUR- SOR Down button to selectPress the Cursor Right but Timer Setting the Start Time Timer Setting the Stop Time Timer Selecting the Channel Press the Numbered butChannel. Or, press the Cursor Once press the Cursor Timer Setting Activate to on or OFFTimer Turning on the Timer Display Then press the Cursor DownOr Cursor Left button to turn You also can block individual channels or block programming Understanding AutolockCode Autolock Setting UP the Access CodeLeft. Then press the Cursor Autolock Blocking ChannelsCursor Down button to high Enter your four-digit Access CODE. Correct willAuto Lock Blocking by Movie Rating Button again to highlightAutolock Blocking by TV Rating Press the Cursor Right or Access Code and the menuAutolock Turning Block on or OFF Enter your four-digitEnter your four-digit Access Code and the menu Autolock Blocking Unrated BroadcastsOr Cursor Left button to Enter your four-digit Access Autolock Blocking Broadcasts That have no RatingOr Cursor Left button to tog Block Unrated No Rating Autolock Reviewing Your SettingsAuto Lock Viewing Blocked Programming Control, press the Cursor Sound Adjusting the Treble , Bass , and BalanceCursor Left button to adjust Use the Cursor Right orVolume Sound Adjusting the VolumeSOR Right or Cursor Left Sound Using the AVL Audio Volume LevelerPress the INCR. SURR. but Sound Using Incredible SurroundTreble Sound Setting the TV for Stereo and SAPAudio OUT Sound Setting the Audio OUT ControlTreble Sound Using the TV Speaker Control and Audio Output JacksSound Using the Surround Sound External Speaker Connections Press the Source button Sound Using the AUDIO/VIDEO Input JacksSuper-Video connection on the rear of the TV can pro Sound Using the AUDIO/VIDEO Input Jacks CONT’DDevice to the Y, Pb, Pr input jacks on the TV Remote Control Using Autopicture Press the Picture buttonPress the Picture button repeatedly to select either PER Remote Control Using Autosound Press the Sound button onPress the Sound button Screen, press the Cursor Remote Control Using Channel SurfPress the CHANNEL+ or Ð Press the Surf button onFirst, use an optional signal PIP Basic ConnectionsConnect the Video OUT jack AV1, AV2, AV3, S-VIDEO Ð for PIP Selecting the Signal SourcePIP Remote Control Buttons PIP Adjusting the Color and Tint Cursor Left button toPress the Cursor Right or Cursor Left button to Cable Box and VCR Connections PIP More ConnectionsPIP More Connections Cont ’D Troubleshooting No Power No Picture No SoundGlossary of Television Terms Index Canada Factory Service LocationsLimited Warranty
Top Page Image Contents