Philips RealFlat CTV w/DBX Stereo manual Important Safety Instructions

Page 3

IMPORTANT SAFETY INSTRUCTIONS

Read before operating equipment

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this apparatus near water.

6.Clean only with a dry cloth.

7.Do not block any of the ventilation openings. Install in accordance with the manufacturers instructions.

8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9.Do not defeat the safety purpose of the polarized or ground- ing-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and third grounding prong. The wide blade or third prong are provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11.Only use attachments/accessories specified by the manu- facturer.

12.Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the app-

aratus. When a cart is used, use caution when moving the cart/apparatus combination to avoid

injury from tip-over.

13.Unplug this apparatus during lightning storms or when unused for long periods of time.

14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15.Damage Requiring Service - The appliance should be serviced by qualified service personnel when:

A.The power supply cord or the plug has been damaged; or

B.Objects have fallen, or liquid has been spilled into the appliance; or

C.The appliance has been exposed to rain; or

D.The appliance does not appear to operate normally or exhibits a marked change in performance; or

E.The appliance has been dropped, or the enclosure damaged.

16.Tilt/Stability - All televisions must comply with recommend- ed international global safety standards for tilt and stability properties of its cabinet design.

• Do not compromise these design standards by applying excessive pull force to the front, or top, of the cabinet which could ultimately overturn the product.

• Also, do not endanger yourself, or children, by placing electronic equipment/toys on the top of the cabinet. Such items could unsuspectingly fall from the top of the set and cause product damage and/or personal injury.

17.Wall or Ceiling Mounting - The appliance should be mounted to a wall or ceiling only as recommended by the manufacturer.

18.Power Lines - An outdoor antenna should be located away from power lines.

19.Outdoor Antenna Grounding - If an outside antenna is connected to the receiver, be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges.

Section 810 of the National Electric Code, ANSI/NFPA No. 70-1984, provides information with respect to proper grounding of the mats and supporting structure grounding of the lead-in wire to an antenna discharge unit, size of grounding connectors, location of antenna-discharge unit, connection to grounding electrodes and requirements for the grounding electrode. See Figure below.

20.Object and Liquid Entry - Care should be taken so that objects do not fall and liquids are not spilled into the enclo- sure through openings.

Note to the CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

Example of Antenna Grounding

as per NEC - National Electric Code

GROUND CLAMP

ELECTRIC SERVICE EQUIPMENT

ANTENNA LEAD IN WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents For fast help, call us first Warranty Verification Important Safety Instructions Table of Contents HOW to USE the Picture Adjustment Controls HOW to USE the DNR Noise Reduction Control SOR Down button until the word HOW to USE the Contrast + Black Stretch ControlButton turn the Contrast + feature Press the Cursor UP or CURWords TREBLE, Bass or Balance HOW to Adjust the Bass , Treble , Balance ControlsOr Left button to adjust Press the Cursor UP or CUR SOR Down button until the wordHOW to USE the AVL Automatic Volume Leveler Control INCR. Surround widens Button to set the Incredible SurroundPress the Cursor UP or Cursor Down button to scroll Setting the TV for SAP Secondary Audio ProgramsSetting the TV to Receive Stereo Programming Press the Clock button on HOW to USE the Timer ControlsUnderstanding the Autolock Controls Over the next few pages you’ll learn how to block channelsSetting UP the Autolock Access Code Blocked with Block Channel HOW to Block ChannelsEnter your Access Code to View a tuned channel that isXxxx HOW to Clear ALL Blocked Channels AT the Same TimeHOW to Block ALL Channels AT the Same Time Blocking Programming Based on Movie Ratings Press the Cursor UP or Down button until AutoLock isPress the Cursor UP or Down button to highlight Press the Cursor UP or Down button to highlight the desired Blocking Programming Based on TV RatingsBlocking Options Using the Auotlock Blocking OptionsHOW to USE the Closed Caption Control Using the AUDIO/VIDEO Input Jacks Using the AUDIO/VIDEO Monitor Output Jacks Press the Play button Connect one end of the S-VIDEOConnect other end of the S Turn the VCR and the TV on Press the CH + or buttons onConnect the red and white Audio Using the Component Video Input JacksSlide the TV/VCR/ACC Switch to the ACC position Connect the Component Y, PbPress its Play button Using the Side Input Jacks and the Headphone JackPress the Sleep button repeatedly Press the Sleep button onPress the Auto Picture button Setting the Auto Picture ControlSetting the Auto Sound Control Press the Auto Sound button onPress the Auto Sound button CH Button Using the Quadra Surf ButtonsFrownie face button will allow you Repeatedly pressing the same COLFind your Three-Digit Code on pages 36-38 Place the TV/VCR/ACC ModePoint the remote control at Remote control number for your brandPoint the remote at the Device Press the VCR Record buttonPress the Auto Sound button Enter the THREE-DIGIT Remote Code Number for yourChange Channels Remote USE with Accessory Devices Search MethodCable Code BOX Numbers Satellite Remote Control Direct Entry CodesVCR Numbers Digital Code Video Disc Numbers Clock TV/VCR Button Using the REMOTE’S VCR ButtonsTV Displays Wrong Channel or No Channels Above Troubleshooting TipsIndex Glossary to Television TermsRenewed
Top Page Image Contents