Philips PRI920CI manual Cursor Down buttons until, T1MERACTIVE on CHANNEL12 Setclock 1000 AMI

Page 17

y;ur television comes with an nscreen clock. During normal

operation the clock appears on the

screen when the STATUS/EXIT but-

ton is pressed or when channel

changes occur

<_ Press the CLOCK button on the remote to display the onscreen

	CLOCK menu.
_	Press the CURSOR UP • OR
	CURSOR DOWN • buttons until
	the words SET CLOCK are high-
	ghted.

<_;_ Enter the current time using

the NUMBERED buttons. If the first number is a single digit first

enter a zero then the dig!t (i.e.,

press 0 , then press "8 ).

<_ Press the CURSOR RIGHT • or CURSOR LEFT ,_ buttons to set either AM or PM time.

Note: The CLOCK onscreen menu can also be accessed through the main menu by pressing the MENU

button; then scrolling up/down with the CURSOR UP • or

CURSOR DOWN • buttons until

the word CLOCK is highlighted. Press the CURSOR RIGHT • button to activate the CLOCK menu and follow the steps above to set the time.

Remember: Be sure to [[ press "0" first and then the

hour number for single digit entries.

To clear the onscreen menu press

the STATUS/EXIT button or wait a

few seconds after you have fin-

ished your adjustment and the

menu will automatically disappear from the screen.

JcK --:-- AMI

T1MERACTIVE ON

CHANNEL12

[SETCLOCK 10:00 AMI

TIMERACqqk_ ON

CHANNEL12

lafpTat_mnesicSSee_time,.the will not

Note: The CLOCK onscreen menu can also be accessed through the main menu

by pressing the MENU button; then

scrolling up/down with the CURSOR UP • or CURSOR DOWN • buttons

until the word CLOCK is highlighted.

Press the CURSOR RIGHT • button to activate the CLOCK menu and follow

the steps above to set the time.

17

Image 17

Contents Avox Safetysymbols SAFETYINSTRUCTIONS- Readbeforeoperatingequipment Setting Setting the Language ControlIntroduction TVsYour Cable TV signal is a sin Round end of the antenna wire is Wire 300 ohm, you first need toIf your antenna has a Found Cable 75 ohm on the end, thenOn the VCR to the 75£2 plug on Ment lid on the back of the remote Remove the battery compartClock Button Cursor ButtonsAgeenglish Toner Cable Autoprogram ThroughItuner TUI,,E-RAutoj SmaFtLockREVEVV Press the Menu button onBrightness Language Enish Tuner Cable Channb EditMemory Channel DeletedSrnartLockREVEVV Brightness Ill PressTint COL.TEMP VolumeNoisereduction OOL Temp Normal RamOr Cursor Leif buttons to activate or deactivate the Noise Press the Menu button onCursor Down buttons until TIMERACqqk onT1MERACTIVE on CHANNEL12 Setclock 1000 AMI By pressing the Menu button thenSetcloo 10Q3 AM Next¢ Press the Clock button to Wntrdthe,tarte2inioeltYotLtooISTARTriME 0830 AMI IMERACTlVEChannel Clock SetupRemote to display the onscreen 1OSEC 30 MINTV-Y OFF OFFTV-G OFF TV-MABlock Press the Cursor Down button until the words ChangeOnIPeosshetSZAZwUcEeTthbeut IchangecodePress the Cursor UP or Cursor Down button until SmartLock Access screen Enter the correct access codePress the Cursor Right This point ALL the previouslyLighted, Press the Cursor AVLUse the Cursor Right or Cursor Left buttons on Cursor UP or CursorChangecode ImovieratingsONI Scroll the menu using Ursor UP or CursorParental Guidelines are SmartLock Review will be high Ighted Press the Cursor Right Play SmartLock DisabledIbassboost oal Press the Menu button on the remote to show the onscreenRIUH4h Cursor LEFTe or Se ected control or OFF GT5 @ Press the Smart Picture button on the remote control. Press the Smart Sound but Trebleboost on Bassboost on Iavloffi Sleeptimer OFFSmartLockI1 VoiceTo select a channel to add to Press the Channel + orPress the Surf button on Still displayed to ADD the channel to Surf listWork Programming The procedure of adding or deleting channel Beaumont/Austin Philips FactoryService oflllinois Philips FactoryServiceof GeorgiaPhilips FactoryServiceof Texas 1110 N. Post Oak Rd., Suite Itasca, lLPage You Color Television