Philips TP3697B1 manual Using the Surround Sound External Speaker Connections

Page 31

USING THE SURROUND SOUND EXTERNAL SPEAKER CONNECTIONS

By adding optional external speakers to the TV’s sound sys-

tem, you can create the feeling of reflected sound that surrounds you at a movie theater or concert hall.

BEGIN

Connect both external speak-

ers to the speaker wire terminals on the TV.

Recommended speakers: 8 ohm, 15 watt minimum. Be sure the (+) and (–) speaker wires are connect- ed to the correct R(ight) and L(eft) speaker terminals on the TV.

Place the speakers so the viewing area is between the TV and the rear surround speakers. (See overhead view drawing.)

Turn the TV and the

STEREO control ON.

After setup whenever a stereo sig- nal is received the audio will be heard in Surround Sound.

SMART HELP

Remember, Surround Sound will not work with only one speaker connected; or

with monaural audio material (unless the Incredible Stereo fea- ture is turned ON).

BACK OF TV

REAR SURROUND SOUND	1
SPEAKER TERMINALS

8

8

	+ R –	– L	+
ATTENTION - TO AVOID DAMAGE	SURROUND SOUND
1. DO NOT CONNECT SURROUND SOUND SPEAKERS
TO A SEPARATE AMPLIFIER OR TO SPEAKERS
CONNECTED TO ANOTHER PRODUCT.
2. DO NOT CONNECT LEFT AND RIGHT SPEAKER	S-VIDEO 1		S-VIDEO 2
OUTPUT TOGETHER.	S-VIDEO 1		S-VIDEO 2
PIP ANT "B"
75Ω			VIDEO
ANT "A"			L
ANT "A"			AUDIO
75Ω			AUDIO
75Ω
			R
	AV1	AV2	AV
	in	in	out

+	-	+	-

REAR SURROUND SOUND SPEAKERS
Note: The rear Surround Sound speakers will not be
heard at the same volume level as the front TV
speakers. It is intended for the rear speakers to give a
background noise effect which requires a lower vol-	TV
ume level than the TV’s front speakers.	TV

2

REAR SPEAKER

REAR SPEAKER

PRIMARY VIEWING AREA

31

Image 31

Contents TP3697B1 Warranty Verification Safety Instructions Read before operating equipment Table of Contents SET-UP and Quick USE Guide FeaturesTo remove the menu from the screen HOW to Adjust the TV PictureButtons to adjust the selected control Press the STATUS/EXIT buttonCursor UP or Cursor Setting the TV’S ClockPress the Cursor Down button until the word Features Press the Numbered buttonsPress the Menu button on Activating the TV’S on Timer ControlRemote to show the onscreen menu Button again to highlight the channel indicator area Selecting the TV’S on Timer ChannelPress the Cursor Down Setting the TV’S on Timer TunerPress the Cursor UP or Cursor Down buttons to To enter the desired start up time Setting the TV’S on Timer Start TimeUse the Cursor UP or CUR Setting the TV’S on Timer Display Movie Ratings Understanding SmartlockSmartLock control Using Smartlock Setting UP the Access CodeEnter current access code Down to highlightInput jacks. Select AV 1 or AV 2 Using Smartlock Blocking ChannelsPress the Channel + or External inputs on the rear of the TVButton to select Movie Rating Using Smartlock Movie RatingPress the Cursor Right Button to access the movie ratings Be highlightedAppear within the menu Using Smartlock TV RatingButton to select TV Rating Options Using Smartlock BlockingUsing Smartlock Block Unrated Left button to set no Using Smartlock no RatingPress the Menu button on the remote to show the on-screen MenuExample Blocking is set to OFF Reviewing the Smartlock SettingsXxxx Viewing Blocked ProgrammingTurning on the Contrast + Control Turning on the Dynamic Noise Reduction Picture ControlTrol Turn the INCR. PICT. feature on orTurning on the Incredible Picture Control Press the Cursor Down to highlight the INCR. PICT. conCaption MODECC1, CC2, CC3, CC4, CC MUTE, or OFF Using the Closed Caption ControlSleep Using the Sleep Timer ControlUsing TREBLE, BASS, and Balance Sound Controls Stereo selected the television HOW to SET the TV for Stereo ProgramsWill reproduce any stereo broad- cast signal it receives Button to select the Sound menuPress the Volume + or but Using the Incredible Stereo FeatureUsing the TV Volume BAR Control Press the Volume + orPress the Cursor Down button to select the Speaker Using the TV Speaker Control and Audio Output JacksUse the Cursor Right Or Cursor Left Connect both external speak Using the Surround Sound External Speaker ConnectionsConnect the Video yellow HOW to USE the AUDIO/VIDEO Input JacksCable to the Video OUT jack on the back of the VCR. Then Not Supplied Connect the S-VIDEOOnce you find the remote Using the Remote Locator FeaturePress the Power button on Within a few seconds a Chirping or beeping sound willNot be needed but for your infor Homing signalNaled when the TV is turned For most homes this step wouldPress the SmartPicture button Press the Smart PicturePress the Smart Sound but Using the Smartsound ControlPress the Surf button on Using the TV’S Channel Surf ControlPress the Cursor Left Is necessary Setting the Remote Control to Work with Other DevicesEnter the THREE-DIGIT Place the TV/VCR/ACCPress the VCR Record Press the SmartSound buttonMode Switch in the proper posi Tion Press the Power button onDevice your are attempting to program to turn on Remote VCR Code no Remote Control Direct Entry CodesRemote Dvdcode no Using the REMOTE’S VCR Buttons Hooking up PIP Using the PIP PICTURE-IN-PICTURE FeatureAV 1, AV 2, S-VIDEO Turn the TV and VCR orPress the PIP ON/OFF but Press the PIP Source butPress the PIP Position Press the PIP ON/OFF butPress the PIP ON/OFF button Pressing the ON/OFF button aAdjusting the PIP Color and Tint On the VCR to the Video in jack on the TV First use an optional signalMore PIP PICTURE-IN-PICTURE Connections TelevisionConnect the ANT OUT jack on First connect the original cableConnect the yellow Video Cable Tips if Something Isnt Working TV Displays Wrong Channel or No Channels AboveGlossary to Television Terms Index Philips Consumer Electronics Company Texas Limited Warranty