Philips TP3697B1 manual Setting the Remote Control to Work with Other Devices, Is necessary

Page 39

SETTING THE REMOTE CONTROL TO WORK WITH OTHER DEVICES
our remote control is set to
Ywork your TV and many
infrared remote (IR) control
VCRs, Cable Boxes, Satellite
Systems, DSS, DVD, etc.
However, an easy onetime step
may be necessary before the			LOCATOR
remote will work your VCR.	1
Try this initial check to see if
going on to the following section		TV		AV		ON/OFF	POSITION
is necessary.
BEGIN
Place the TV/VCR/ACC		VCR		SWAP		SOURCE
Place the TV/VCR/ACC							UP
Mode Switch in the proper posi-	VCR						UP
Mode Switch in the proper posi-	VCR
tion.		ACC
		ACC
Point the remote control at
the device and press the POWER
button.
Does the remote turn the
device ON?							2
				POWER
If YES, stop and try other func-	Satellite Receiver	LOCATOR			FREEZE
				POSITION
			AV	ON/OFF	PIPCH	DN
tion buttons on the remote. If		TV		SOURCE	UP	DN
				SWAP
			VCR

they also work the device, then				ACC
they also work the device, then						SMART
the remote is ready and no fur-					SMART	PICTURE
						SURF
					SOUND
ther steps are needed.						MENU
ther steps are needed.
							CH
If NO, continue...	Cable Converter					VOL	MUTE
							A/CH
						CC	STATUS CLOCK
							TV/VCR
							EXIT
								TUNER
								A/B
							SLEEP	MULTI
							VCR	MEDIA
							RECORD	INCREDIBLE
								STEREO
First look up a THREE-DIGIT
remote control number for your
brand of Device before going
through the simple steps on the
following page.
Find your Three-Digit Code on
pages 42-43.
SMART HELP
Remember, if more than
one number is listed, you may
have to try more than the first Three-
Digit code given in order to locate
your Device’s remote code.
	39

Image 39

Contents TP3697B1 Warranty Verification Safety Instructions Read before operating equipment Table of Contents SET-UP and Quick USE Guide FeaturesTo remove the menu from the screen HOW to Adjust the TV PictureButtons to adjust the selected control Press the STATUS/EXIT buttonCursor UP or Cursor Setting the TV’S ClockPress the Cursor Down button until the word Features Press the Numbered buttonsActivating the TV’S on Timer Control Press the Menu button onRemote to show the onscreen menu Button again to highlight the channel indicator area Selecting the TV’S on Timer ChannelSetting the TV’S on Timer Tuner Press the Cursor DownPress the Cursor UP or Cursor Down buttons to Setting the TV’S on Timer Start Time To enter the desired start up timeUse the Cursor UP or CUR Setting the TV’S on Timer Display Movie Ratings Understanding SmartlockSmartLock control Using Smartlock Setting UP the Access CodeEnter current access code Down to highlightInput jacks. Select AV 1 or AV 2 Using Smartlock Blocking ChannelsPress the Channel + or External inputs on the rear of the TVButton to select Movie Rating Using Smartlock Movie RatingPress the Cursor Right Button to access the movie ratings Be highlightedUsing Smartlock TV Rating Appear within the menuButton to select TV Rating Options Using Smartlock BlockingUsing Smartlock Block Unrated Left button to set no Using Smartlock no RatingPress the Menu button on the remote to show the on-screen MenuExample Blocking is set to OFF Reviewing the Smartlock SettingsXxxx Viewing Blocked ProgrammingTurning on the Contrast + Control Turning on the Dynamic Noise Reduction Picture ControlTrol Turn the INCR. PICT. feature on orTurning on the Incredible Picture Control Press the Cursor Down to highlight the INCR. PICT. conCaption MODECC1, CC2, CC3, CC4, CC MUTE, or OFF Using the Closed Caption ControlSleep Using the Sleep Timer ControlUsing TREBLE, BASS, and Balance Sound Controls Stereo selected the television HOW to SET the TV for Stereo ProgramsWill reproduce any stereo broad- cast signal it receives Button to select the Sound menuPress the Volume + or but Using the Incredible Stereo FeatureUsing the TV Volume BAR Control Press the Volume + orUsing the TV Speaker Control and Audio Output Jacks Press the Cursor Down button to select the SpeakerUse the Cursor Right Or Cursor Left Connect both external speak Using the Surround Sound External Speaker ConnectionsHOW to USE the AUDIO/VIDEO Input Jacks Connect the Video yellowCable to the Video OUT jack on the back of the VCR. Then Not Supplied Connect the S-VIDEOOnce you find the remote Using the Remote Locator FeaturePress the Power button on Within a few seconds a Chirping or beeping sound willNot be needed but for your infor Homing signalNaled when the TV is turned For most homes this step wouldPress the SmartPicture button Press the Smart PicturePress the Smart Sound but Using the Smartsound ControlUsing the TV’S Channel Surf Control Press the Surf button onPress the Cursor Left Is necessary Setting the Remote Control to Work with Other DevicesEnter the THREE-DIGIT Place the TV/VCR/ACCPress the VCR Record Press the SmartSound buttonPress the Power button on Mode Switch in the proper posi TionDevice your are attempting to program to turn on Remote VCR Code no Remote Control Direct Entry CodesRemote Dvdcode no Using the REMOTE’S VCR Buttons Hooking up PIP Using the PIP PICTURE-IN-PICTURE FeatureAV 1, AV 2, S-VIDEO Turn the TV and VCR orPress the PIP ON/OFF but Press the PIP Source butPress the PIP Position Press the PIP ON/OFF butPress the PIP ON/OFF button Pressing the ON/OFF button aAdjusting the PIP Color and Tint On the VCR to the Video in jack on the TV First use an optional signalMore PIP PICTURE-IN-PICTURE Connections TelevisionFirst connect the original cable Connect the ANT OUT jack onConnect the yellow Video Cable Tips if Something Isnt Working TV Displays Wrong Channel or No Channels AboveGlossary to Television Terms Index Philips Consumer Electronics Company Texas Limited Warranty