Philips 20HF5335D,26HF5335D, 32HF5335D Installation Procedure consists of three simple steps

Page 71

The Philips SmartLoader works in 2 modes – Wireless and Wired:

Wireless mode ---- through infrared sensor (15/20HF5234)

 

Switch the SmartLoader to “Wireless” mode by sliding the side-switch to the

icon on the SmartLoader

device. Point the Wireless SmartLoader to the TV’s infrared receiver (optimal distance of 5-30cm) and proceed with the Installation procedure listed below.

Wired mode ---- using the by-packed accessory cable(s) (20/26/32HF5335D)

 

Switch the SmartLoader to “Wired” mode by sliding the side-switch to the

 

 

icon on the SmartLoader

 

 

 

device.

 

Examine the rear connectors of the TV set to determine if the 3-pin or 4-pin female connector wire (packed with the Wireless SmartLoader) should be used. Plug in the correct connector wire to the corresponding opening on the TV set (usually marked as SERV C), and then connect the RJ11 jack end of the accessory wire to the RJ11 socket on the SmartLoader.

The Installation Procedure consists of three simple steps:

1. Choosing a Master TV

The Master TV is the TV set whose installation and configuration settings are to be copied into other TV’s (of the same type only).

2. Programming the SmartLoader with the settings from the Master TV

Follow these steps to program the SmartLoader with the settings of the Master TV.

a)Wireless method

Set the SmartLoader to “Wireless” mode using the side switch.

Turn on the TV, and while holding the SmartLoader, point it in the direction of the TV. Press the “MENU” Key on the SmartLoader.

b) Wired method

Connect the SmartLoader to the TV using the appropriate accessory cable. Set the SmartLoader to “Wired” mode using the side switch.

Turn on the TV, and while holding the SmartLoader, point it in the direction of the TV. Press the “MENU” Key on the SmartLoader.

The Master TV will show the following menu:

SMARTLOADER TO TV >

TV TO SMARTLOADER >

On the TV screen, highlight the menu option “TV TO SMARTLOADER”

Press the right arrow key on the SmartLoader to start the programming process

A number display (from 0~100) will be shown on screen, indicating the percentage of the programming progress from the TV to the SmartLoader. When the programming is completed, “##” will show “100” and the message “DONE” will appear.

TV TO SMARTLOADER ## (0-100)

The SmartLoader is programmed and can be used to install and configure other TVs.

Copying the settings of the Master TV to other TVs with the SmartLoader

Follow these steps to install and configure the settings of a Philips TV with the SmartLoader.

- 6 -

Page 70 Page 72
Image 71
Page 70 Page 72
Contents Hospitality Television 20/26/32HF5335D 15/20HF5234 Installation of your Philips Hotel TV Switch on Settings Standby Last Status Cloning of settings Installation Procedure consists of three simple steps Problems and Solutions Disposal of your old product Page Luxemburg 40 6661 Local Netherlands 0900 Country Number Tariff Austria 0820Belgium 070 222 Germany 0180 5 356Disposal of your old product Standby Power Consumption for this set is less than 1 WRecycling Product informationTable of contents Troubleshooting Glossary Features 26.1Using the TV in HD High Definition mode Connecting other equipmentTip Reduce contrast and brightness when viewingIntroduction Important information Stationary images on the TV screenMode. Use the P + / or to keys to select channels What is digital TV?Digital or Analogue channels? Care of the screen SafetyGeneral Lead during lightning stormsCI Common Interface slot to Program / + to select programmes Rear connectorsSide connectors Side controlsConnect the mains Switching on the TVUsing the Remote Control Getting startedOptions See Cancel Sound modeSubtitles mode Analogue or Digital modeMute Volume + VOLDigital menu 13 OKName Setup Favourites ListInformation System software Setup Preferences LanguageAccess restrictions LocationInstallation Service lists Service setup Test reception SetupFactory default settings InstallationBanner description Symbols descriptionUnderstanding the information on the banner View new TV channels or Listen to new Radio stations Service listsRearrange services Select Reinstall all services ï and press Æ key Service setupAdd new services Reinstall all servicesSelect Manual install services ï and press Æ key Press the key to start the installationManual install services Use the Æ key to enter the Frequency Use the ï key to select Installation and press the Æ keyTest reception Select Language or Location ï and press Æ key Language default settingsLocation settings PreferencesAccess restrictions Select TV channels use the Î ï keys Setting up your favourite listOff Air Downloading of new software InformationPress the white key to exit the menu Using the Options menuSubtitle language use the Î ï keys To temporarily change the language Confirm with keyTV Guide Preset/Servcie Now NextOccurrence select Once, Daily or Subtitle language make yourSubtitles for hearing impaired Not applicable for this model Available in U.K. only Digital teletext MhegModule slot Switch off the TV CommonInserting the CAM ModulePress the ï key to select Auto Store ATS Automatic Tuning System featureACI Automatic Channel Installation feature Enter into Digital mode to do so refer to PreferencesonFine Tune SystemSearch Program NoProgramme Sort Press the ï key to select Sort Key to enter sort modeNaming of Channel Selecting your Favourite Programmes Select Off option to deactivate the feature FeaturesTimer Clear All Parental LockLock Program Change CodeActive Control Child LockDescription of the Sound settings Picture and Sound settingsDescription of the Picture settings Natural Definition of Picture SettingsDefinition of Sound Settings Smart Picture and SoundSuper Wide Screen FormatsSubtitle Zoom Movie ExpandTeletext Favourite pages Hidden informationEnlarge a Picture/TeletextUsing the TV as a PC Monitor Sound menu Connecting the HD equipmentControl TV settings while in HD mode 480i Supported formats HD formatSD format Overview of connections Connecting other equipmentConnect Decoder and VCR Connect VCR or DVD recorder With a eurocableAs shown Connect the eurocable With the aerial cable onlyWith the aerial cables only With Component Video connectorsConnect 2 VCRs or VCR and DVD recorder With eurocables Connect the aerial cables 1 , 2 and 3 as shownAudio jack of EXT4 Audio L and R jacks and to the L/RVGA connection is not supported PC equipped with a DVI connectorSupported PC resolutions Connect a PCConnect a Camera, Camcorder Connect a Headphone Game console Troubleshooting Screen that do not Symptom Possible solutions No digital channelsPicture in HD mode One or a few tiny spots onHdmi High-Definition Multimedia Interface GlossaryPage Hospitality Television 20/26/32HF5335D 15/20HF5234 Installation of your Philips Hotel TV Switch on Settings Standby Last Status Low Battery Check Installation Procedure consists of three simple steps Problems and Solutions Disposal of your old product
Top Page Image Contents