Philips 22PFL3805H Access decoder channel, Start a TV demo, Reset the TV to factory settings

Page 34

Access decoder channel

You can map channels provided through a decoder or descrambler to yourTV channel selection. In this way, you can select these channels by using the RC of yourTV.The decoder or a descrambler must be connected to EXT1 (SCART).

Set decoder channel

Map channels from a decoder or descrambler.

1Press.

2Select [Setup] > [Installation] > [Decoder].

3Pressto enter [Decoder] menu.

4Pressto select [Channel], then press to enter.

5Select one channel to map to the decoder / descrambler channel and press OK to conﬁrm.

6Select [Status], then pressto enter.

7Select [EXT 1] (SCART) the connector used by the decoder / descrambler.

8Press OK.

9Pressto exit.

Note

•Select [None] if you do not want to map to the decoder / descrambler channel.

Start a TV demo

You can use demonstrations to better understand the features of your TV. Some demos are not available on certain models. Available demos are displayed in the menu list.

1Press DEMO on the remote control.

2Press to select a demo and press OK to view it.

3Press DEMO to exit.

Reset the TV to factory settings

You can restore the default picture and sound settings of yourTV.The channel installation settings remain the same.

1Press.

2Select [Setup] > [Installation] > [Factory settings].

3Pressto enter [Factory settings].

4Select [Reset] to start resetting.

5Press OK.

6Pressto exit.

32EN

Image 34

Contents Register your product and get support at 22PFL3805H =BCDEFGHIEGJFCD Contents Mains fuse UK only Koninklijke Philips Electronics N.V.All rights reservedCompliance with EMF Remove fuse cover and fuseCopyright in the UK CopyrightTrademarks ComplianceSafety Screen care Product careDisposal of your old product and batteries High energy efﬁciency Low standby power Environmental effortsSide controls and indicators Your TVRemote control Backward within the titleRemote control usage Switch channels with the channel grid Switch your TV on / off or to standby Switch channelsUse your TV Watch connected devices Adjust TV volumeUse the source button Play a disc Play discUse video options Use audio options More play features for discUse picture options Play a musical slideshowAccess the setup menu Change settingsSwitch camera angles Change general settingsChange audio settings Change preference settingsUpdate software from a CD-R Update the disc player softwareCheck software version Rename devices from the home menu Access TV menusUse more of your TV Press OK to conﬁrm your choice Press to exitRemove devices from the home menu Change picture and sound settingsUse settings assistant Use smart pictureManually adjust picture settings Change picture formatSummary of picture formats Following picture settings can be conﬁguredUse smart sound Use the universal access menu Manually adjust sound settingsSelect teletext subpages Use advanced teletext featuresAccess the teletext options menu Select T.O.P. teletext broadcastsView all channels Switch on EPGUse the Electronic Programme Guide Add a channel to a favourite listUse the TV clock Change the time zone Use timersAutomatically switch the TV to standby sleep timer Use daylight savingSet or change your PIN code Automatically switch the TV on on timerUse TV locks Lock or unlock the TVLock or unlock one or more channels Enable subtitles on analogue TV channelsUse subtitles Set parental ratingsSelect a subtitle language on digital TV channels Enable subtitles on digital TV channelsView photos View a slide show of your photos Change slide show settingsMusic settings Listen to musicUpdate the TV software Listen to digital radio channelsUpdate using OAD Change TV preferencesStart a TV demo Access decoder channelReset the TV to factory settings Set decoder channelInstall channels Automatically install channelsSearch and store new TV channels Manually install channelsSelect your system Fine-tune analogue channelsRearrange channels When complete, select Store to store the frequencyRename channels Test digital receptionConnect devices Back connectorTV Antenna Signal input from an antenna, cable or satellite EXT 1 Cvbs and RGBSERV. U For software update Side connectorPC in VGA and Audio Audio and video input from a computer Hdmi cable and HDMI-DVI adaptor Connect a computerHdmi cable DVI-HDMI cable VGA cableInsert and activate a CAM Use a Conditional Access ModuleAccess CAM services After inserting and activating the CAM, pressUse Philips EasyLink System audio control and enable the TV speakers Use a Kensington lockDisc player Supported TV mounts PowerProduct speciﬁcation Laser speciﬁcationTV channel issues TroubleshootingGeneral issues Picture issuesDisc player issues Sound issuesHdmi connection issues Computer display on the TV is not stable Computer connection issuesContact us Set the TV picture format to unscaledSubtitles IndexAnalogue ﬁne-tune Antenna Batteries Bracket for wall mount CAM teletext disconnect USBHdmi With slideshow Mute TV speakers29 U 50 EN Page 52 EN Koninklijke Philips Electronics N.V. All rights reserved