Philips 60PW9383, 55PW9383 manual Swap, Adjusting the Manual Converge Controls Multipoint RED/BLUE

Using the On-screen Submenus: Picture

ADJUSTING THE MANUAL CONVERGE CONTROLS: MULTIPOINT RED/BLUE

The Multipoint Red/Blue Convergence controls allow you to adjust picture convergence at

specific points on the TV screen.

1 Press the MENU/SELECT button to show the on-screen menu. Press the CURSOR RING RIGHT to enter the PICTURE menu, then the CURSOR RING DOWN repeatedly until MANUAL CONVERGE is highlighted.

2 Press the CURSOR RING RIGHT to enter the MANUAL CONVERGE sub- menu. Press the CURSOR RING DOWN repeatedly until MULTIPOINT RED or MULTIPOINT BLUE is highlighted. Then press the CURSOR RING LEFT or RIGHT to enter Navigate mode.

3 Press the CURSOR RING LEFT, RIGHT, UP, or DOWN to move to a cross hair that has a color outline. Then press the STATUS/EXIT button to enter adjust mode.

4 Press the CURSOR RING LEFT, RIGHT, UP, or DOWN to adjust the cross hair until the color outline is gone.Then press the STATUS/EXIT button to return to NAVIGATE mode. Repeat steps 3 and 4 until all misaligned cross hairs have been adjusted.

5 For your adjustments to be stored in the TV’s memory, you must activate SAVE MULTIPOINT.

NOTE: If you are not satisfied with the adjustments you just made and want to start over, you can use the UNDO MULTIPOINT control. This control allows you to undo the adjustments, but only if you use it before saving.

To save your multipoint adjustments, press the MENU/SELECT button to return to the MANUAL CONVERGE menu. Press the CURSOR RING DOWN repeatedly until SAVE MULTIPOINT is highlighted. Then press the CURSOR RING LEFT or RIGHT to store your adjustments in the TV’s memory.

Or, to undo the multipoint adjustments you just made, highlight UNDO MULTIPOINT and press the CURSOR RING LEFT or RIGHT.

Or, to restore the TV’s convergence to factory settings, highlight RESTORE FACTORY and press the CURSOR RING LEFT or RIGHT.

6 Press the STATUS/EXIT button to exit the menu.

PICTURE

MANUAL CONVERGE

CONVERGE RED

CONVERGE BLUE

MULTIPOINT RED

MULTIPOINT BLUE

SAVE MULTIPOINT

		POWER
TV	VCR	ACC
3,4 SWAP		ACTIVE
	DN PIP CH UP	CONTROL FREEZE 2
STATUS/		MENU/
EXIT		SELECT
6 VOL	MUTE	CH 1,5
1	2	3
4	5	6
7	8	9
TV/VCR	0
A/CH		SURF
	POSITION	PIP

HELPFUL HINTS

•The on-screen display will disappear after 20 seconds of inactivity. If this happens, simply press the

MENU/SELECT button to bring the

MANUAL CONVERGE submenu back.

•If you should experi- ence a power outage before saving your multipoint-convergence settings, your settings will be lost.

PICTURE

MANUAL CONVERGE

CONVERGE RED

CONVERGE BLUE

MULTIPOINT RED

▲MULTIPOINT BLUE

▲	SAVE MULTIPOINT	É
			to Navigate Exit to Adjust

to Navigate Exit to Adjust to Adjust Exit to Navigate

			to Navigate Exit to Adjust						to Adjust Exit to Navigate
						PICTURE
							MANUAL CONVERGE
								CONVERGE RED
								CONVERGE BLUE
								MULTIPOINT RED
							▲	MULTIPOINT BLUE
							▲	SAVE MULTIPOINT		É
			to Adjust Exit to Navigate
				SAVE MULTIPOINT
PICTURE						PICTURE
	MANUAL CONVERGE						MANUAL CONVERGE
		CONVERGE RED						CONVERGE RED
		CONVERGE BLUE						CONVERGE BLUE
		MULTIPOINT RED						MULTIPOINT RED
	▲	MULTIPOINT BLUE					▲	MULTIPOINT BLUE
		SAVE MULTIPOINT						SAVE MULTIPOINT		STORED
					OR
				UNDO MULTIPOINT
PICTURE						PICTURE
	MANUAL CONVERGE						MANUAL CONVERGE
		CONVERGE BLUE						CONVERGE BLUE
		MULTIPOINT RED						MULTIPOINT RED
		MULTIPOINT BLUE						MULTIPOINT BLUE
	▲	SAVE MULTIPOINT					▲	SAVE MULTIPOINT
		UNDO MULTIPOINT						UNDO MULTIPOINT		RESTORED
					OR
				RESTORE FACTORY
PICTURE						PICTURE
	MANUAL CONVERGE						MANUAL CONVERGE
		MULTIPOINT RED						MULTIPOINT RED
		MULTIPOINT BLUE						MULTIPOINT BLUE
		SAVE MULTIPOINT						SAVE MULTIPOINT
	▲	UNDO MULTIPOINT					▲	UNDO MULTIPOINT
		RESTORE FACTORY						RESTORE FACTORY		RESTORED

34