Philips 55PW9383, 60PW9383 manual Setting the TIMER’S Start Time and Stop Time

Page 43

Using the On-screen Submenus: Features

SETTING THE TIMER’S START TIME AND STOP TIME

You can set the Timer to switch to a selected channel at a specific time while you are watching another channel, or when the TV is in standby mode. (Standby mode is when the TV is

plugged into the wall outlet but turned off.) If you want, you can also set the TV to turn off at some time after the TV switches channels. Follow the steps below to set the Timer’s START TIME and STOP TIME.

1 Press the MENU/SELECT button on the remote control to show the on- screen menu.

2 Press the CURSOR RING DOWN

twice to highlight FEATURES.

3 Press the CURSOR RING RIGHT to enter the FEATURES submenu.

4 Press the CURSOR RING RIGHT again. Then press the CURSOR RING DOWN once to highlight the START TIME control.

5 Press the CURSOR RING RIGHT to highlight the time indicator area.

6 Press the NUMBER buttons to enter the correct time. If you make a mis- take entering the time, use the CUR- SOR RING LEFT or RIGHT to move among the time input slots to make corrections.

NOTE: You can also use the CUR- SOR RING UP or DOWN to cycle through digits to input the time.

7 Press the CURSOR RING UP or DOWN to select AM or PM.

8 Press the CURSOR RING LEFT repeatedly until START TIME is high- lighted. Then press the CURSOR RING DOWN to highlight STOP TIME. If you want the TV to switch off at some time after the changing of channels, follow steps 5–7 above to set the STOP TIME.

9 Press the STATUS/EXIT button to exit the menu.

See pages 44 and 45 for instructions on selecting the Timer’s channel and activating the timer.

PICTURE	TIMER
SOUND	AutoLock
FEATURES	PIP
INSTALL	CLOSED CAP
	FORMAT

			POWER
	7	VCR	ACTIVE ACC	3,4,
	7	PIP CH	CONTROL FREEZE	5
9		UP
9	SOUND
	STATUS/		MENU/
	EXIT		SELECT
	8	MUTE	2	1
			2	1
	1	2	3
	4	5	6
	7	8	9
6	TV/VCR	0
	A/CH	0	SURF
		POSITION	PIP

FEATURES
		TIME
	TIMER	TIME
	AutoLock	START TIME
	PIP	STOP TIME
	CLOSED CAP	CHANNEL
	FORMAT	ACTIVATE

FEATURES
TIMER
TIME	8:06 PM

START TIME

STOP TIME

CHANNEL

ACTIVATE

FEATURES

TIMER

TIME

START TIME

_ _:_ _

STOP TIME

CHANNEL

ACTIVATE

FEATURES
TIMER
TIME
START TIME	8:00 AM
STOP TIME
CHANNEL
ACTIVATE

FEATURES

TIMER

TIME

START TIME

STOP TIME	_ _:_ _
CHANNEL
ACTIVATE

FEATURES
TIMER
TIME
START TIME
STOP TIME	9:30 AM
CHANNEL
ACTIVATE

43

Image 43

Contents Hdtv Monitor Warranty Verification Important Safety Instructions Contents End-of-life Disposal FeaturesWhat You Can Connect to Standard Panel Jacks Panel Overview Standard Inputs and OutputsWhat You Can Connect to High-definition Input Jacks Panel Overview HIGH-DEFINITION InputsRear of TV Connecting a VCRConnecting a VCR and Cable BOX Using AN Audio HI-FI System with Your TV ConnectingSee the section below on using the Audio OUT control Making Optional SURROUND-SOUND Connections Four paired wires for speaker connectionsRear of DVD Player Connecting a Standard DVD PlayerRear of Device with Video Output Connecting AN S-VIDEO DeviceAV4 Connecting a DVD Player with PROGRESSIVE-SCAN CapabilityConnect S-VIDEO and audio cables. Note This example uses Connecting AN HD Receiver to the HD INPUT-AV 4 JacksConnect coaxial cables VOL Connecting a CamcorderTV’s side panel has a headphone jack for personal listening Connecting and Using Headphones with Your TVVCR Programming the TV Remote to Work with Accessory DevicesPlease read through all the steps before beginning Using the CODE-ENTRY Method to Program Your TV RemoteUsing the Search Method to Program Your TV Remote VCR DIRECT-ENTRY Codes for A/V Accessory DevicesTelevision CH & TV/VCR Using the TV Remote with Accessory DevicesSource you want to watch Using the AV and Source Select ButtonsAutoSound Options Using AutosoundColor Picture Using AutopictureSurf List Empty Using AutosurfProgram List CVI Using Program List and Alternate ChannelSleep Timer Control UsingPicture-adjustment Options Adjusting the Picture ControlsPress the STATUS/EXIT button to turn the menu off Setting the EYE Fidelity ControlMIN Setting the Dynamic Contrast ControlConverge RED Adjusting the Manual Converge Controls Converge RED/BLUESwap Adjusting the Manual Converge Controls Multipoint RED/BLUEBalance Adjusting the TREBLE, BASS, and Balance ControlsUsing the AVL Audio Volume Leveler Control Selecting the SURROUND-SOUND Modes Selecting a Surround-sound Option Using Remote ControlSelecting the STEREO/MONO Sound Mode Selecting SAP Using Remote Control Selecting the SAP Second Audio Program FeatureSelecting SAP Using TV Buttons Speakers Using the Bass Boost ControlFeatures Setting the ClockChannel Displaying the TimeTime Setting the TIMER’S Start Time and Stop TimePress the Cursor Ring Right to enter the Features submenu Selecting the TIMER’S ChannelSetting the TIMER’S Activate Control Understanding Autolock Features Setting UP the Autolock Access CodeInstall Using Autolock to Block ChannelsFormat Using Autolock to Block by Movie RatingUsing Autolock to Block by TV Rating Turning the Autolock Blocking Control on or OFF Using Autolock to Block Unrated Broadcasts To highlight the AutoLock Control Using Autolock to Block Broadcasts That have no RatingRIGHT. Then press the CUR SOR Ring Down oncePress the STATUS/EXIT button on Reviewing Your Current Autolock SettingsMute Using the Closed Captioning ControlSelecting a Picture Format Using the Remote Control Using the PICTURE-FORMAT ControlSelecting a picture Format Using the TV Buttons Turning Active Control on or Off Using the TV Buttons Using Active ControlWhen the Inputs Are Used with RGB Video Signals Model SpecificationsSpace for HD INPUT-AV Setting ColorVideo-game images and scoreboards Care and CleaningTV has no power TroubleshootingYou are not able to get sound Glossary of Television Terms Index Canada Factory Service LocationsAtlanta Cleveland Chicago This page is intentionally left blank This page is intentionally left blank Page Projection Television Limited Warranty