Philips 55PP9753/17 setup guide Remote Control Buttons

Page 4

Using the Remote Control

Remote Control Buttons

Select (CBL VCR DVD SAT AMP) and Backlight

Press this button to cycle across the accessory mode dial. Stop pressing when the mode you desire is lighted. The light will stay on for 2 seconds and then begin blinking to indicate the remote is in your desired mode. Once the mode is selected, you must press a button within 60 sec- onds for the remote to remain in the selected mode or it will default back to the TV mode. Pressing and holding the Select button for 2 seconds backlights the remote control buttons. The buttons remain lighted for 5 seconds after you press Select.

Source

Press to display a list of source options—TV, AV1, CVI, AV2, AV3, AV4, or Side. If you have labeled the source you desire, press the Source Select button to toggle to the source. If you have not labeled the source, use the Cursor Up/Down buttons to select the source, then press the OK button to confirm.

Alternate Audio (SAP)

When you tune to a channel where SAP (Second Audio Program) is available, you can toggle between Main and SAP. If SAP is not available, the Alternate Audio menu item cannot be selected. (See page 43 in the Directions for Use manual.)

Pixel Plus™ Demo

Press to activate the demo, which illustrates the benefits of Pixel Plus™. Press and the TV screen will be divided in half displaying the Pixel Plus™ Demo. The left side will show the picture with Pixel Plus™ switched off. The right side of the screen will show the picture with Pixel Plus™ switched on. Press the Pixel Plus™ button again to turn the demo off. (See page 31 in the Directions for Use manual.)

OK

Press to activate or confirm menu choices.

Freeze Format

Pressing will apply one of the Freeze modes you set using the on-screen menu. See page 62 in the Directions for Use manual.

Freeze mode stops action in the main screen. Sound will continue to be heard. Press again to resume nor- mal viewing.

Replay mode displays a few seconds of stored video in the PIP window.

Photo Finish mode displays six stored frames from the picture.

NOTE: Continuing to hold the Freeze Format button down will cycle the TV through the Freeze modes: Freeze, Replay, and Photo Finish.

VOL (Volume)

Press + or – to adjust the volume.

Mute

Press to interrupt or restore sound.

Information Plus+

Press to show information (when available) about the current channel, program, source, number or name, local time, CC availability, SAP availability, program ratings, display format, sound mode, and remaining length of a Sleeptimer setting.

Dual Screen/PIP (Picture-in-Picture)

Press to turn the PIP dual screen on or off. Continuing to hold the Dual Screen/PIP button down will cycle through the Dual Screen/PIP options. (See page 61 in the Directions for Use manual.)

Active Control Plus, AutoSurf, Incredible Surround, and Pixel Plus are trademarks of Philips Consumer Electronics. Copyright 2003 Philips Consumer Electronics. All rights reserved.

*Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

Standby–On

Press to turn the TV on or off.

NOTE: The TV is never really powered off completely unless it is physically unplugged from the power source.

Surround Sound

Press to display and toggle a list of available sound modes. Choose from Incredible Surround™ and Dolby* Virtual settings. (See page 42 in the Directions for Use manual.)

VCR Functions

When the remote is in the VCR mode, these buttons will allow you start a recording (), rewind a tape (), stop the playback of a tape (), play a videotape (), or fast-forward a videotape ().

Time Display

Press to display the current time on the TV screen.

CC (Closed Captioning)

Press to toggle Closed Captioning off, on, or on during mute. (See page 64 in the Directions for Use manual.)

Cursor Up, Down, Right, Left

Use to navigate the on-screen menu and make control adjustments or settings.

Additionally, use these buttons to pan the screen up or down to show any excluded parts of the picture. Left or right panning is possible with the Side input source when “Game” is selected as the type of source for the Side input.

Also use with the Dual Screen/PIP feature to select a screen, as well as resize or reposition a PIP screen. (See page 61 in the Directions for Use manual.)

Menu On/Off

Press to display the TV’s on-screen menu or to turn it off.

CH (Channel Selection)

Press to browse through the TV channels. If you press and hold the channel will change slowly for five chan- nels, then rapidly scroll through the channels. release the button to stop.

Digit (Number Buttons)

Press to directly access a specific TV channel. For a two- or three-digit channel, enter all numbers. Press a single- digit button and hold a bit longer to directly access a sin- gle-digit channel. These buttons can also be used to enter values in certain on-screen menu controls.

PP (AutoSurf™)

If you set the Surf control in the TV’s on-screen menu to two channels, this button will allow you to toggle between the current channel and the last viewed channel. If you choose the nine-channel Surf, pressing this button allows you to access the Surf list, where you can add, remove, and scroll up to nine of your favorite channels. See page 59 in the Directions for Use manual.

Picture Format

Press to display a list of available picture formats for showing video images in the traditional 4:3 proportions. Press this button repeatedly to select a picture format. Choose from Automatic, Super zoom, Panoramic, 4:3, Movie expand 14:9, Movie expand 16:9, 16:9 subtitle, and Wide screen. See pages 35–36 in the Directions for Use manual.

NOTE: To switch between a full or 4:3 letterbox picture format in Dual Screen mode, press the Picture Format button.

Active Control Plus™

NOTE: Active Control™ Plus is not available for use with the AV3 and AV4 input sources.

Press to display the Active Control Plus™ screen. With the “Active Control” submenu selected, press the Cursor Up or Down button to select Off, Minimum, Medium, or Maximum. Maximum is the recommended option. Press the Cursor Right button to select the “Auto Picture” or “Active Display” submenus, then press the Cursor Up or Down buttons to make selections. See pages 27-29 in the Directions for Use manual.

4

Image 4
Contents Contents Positioning the TVMaking Basic Connections to the TV Cable TVCable Box with A/V Outputs Cable Box with RF IN/OUTAntenna IMPORTANT! Initial TV Setup Using the TV ButtonsUsing the Remote Control Installing the BatteriesRemote Control Buttons Using the On-screen Menu Using the Installation Features Using the Demo ModeLanguage Press the Menu button on the remote control to show Press the Cursor Down button repeatedly until InstallPress the Cursor Down button to select the Install Mode controlPress the Cursor Down button to select Settings Press the Cursor Right button to select GeneralPress the Cursor Down button repeatedly until IntelliSense is selected