Philips CCC 193AT, CCC 133AT owner manual Timer Recording cont’d

Page 33

Timer Recording (cont’d) 33

4

Use the Number buttons (1-8) to select a position in which to store the timer recording. Flashing numbers indi- cate an open position (one in which a timer recording has not been stored yet).

NOTE: If you select a number that already has been used to store a timer recording, PREVIOUSLY SET PROGRAM will appear on the screen for a few seconds. Then information about the program in that position will appear on the screen. If this happens, press the STATUS/EXIT but- ton. Then use the Number buttons to select another position.

5

Use the Number buttons to enter the channel of the TV program you want to record.

●If you are recording from line input, press 0, 0. A/V IN will appear on the screen.

●If you are recording using a Cable Box, enter the Cable Box output channel (03 or 04). Be sure to select the channel of the TV program at the Cable Box and leave the Cable Box on for the timer recording.

ONE TIME PROGRAM

PROGRAM 1

CHANNEL – – –

TO CORRECT PRESS CLEAR

TO END PRESS EXIT

6

Press two Number buttons for the hour(s) you want the recording to begin. Press two Number buttons for the minute(s) you want the recording to begin. Press 1 for AM or 2 for PM. For example, for 9:30 PM, press 09, 30, 2.

ONE TIME PROGRAM

PROGRAM 1

CHANNEL	10
TIME ON	– – : – –

TO CORRECT PRESS CLEAR

TO END PRESS EXIT

7

Follow the instructions in step 6 to set the recording’s stop time. (AM or PM will be set automatically.)

ONE TIME PROGRAM

PROGRAM 1

CHANNEL	10
TIME ON	09:30 PM
TIME OFF	– – : – –

TO CORRECT PRESS CLEAR

TO END PRESS EXIT

Instructions continue on page 34.

4-7

EJECT

POWER

MENU STATUS/EXIT CLEAR

1 2 3

4 5 6

7 8 9

SLEEP/	ALT.CH
WAKE UP	ALT.CH
	0
REC	PAUSE
/OTR	/STILL

PLAY

REW F.FWD

STOP

CH.VOL.

MUTE

FM

SPEED F.ADV

TRACKING MEMORY SLOW

Helpful Hints

•If you enter numbers that do not match the TV/VCR’s clock or calen- dar, the entry will be rejected and a question mark will appear on the screen.

•To make corrections while you are programming a timer recording, press the CLEAR button until the cursor is flashing on the item you want to change. Then enter the cor- rect information.

Image 33

Contents Color TV with built-in VCR For Customer Use Dear Philips product ownerThis bolt of lightning indi- cates uninsulated material Model No Serial NoSafety Precautions FeaturesReal-Time Counter Frame Advance Remote Control IntroductionTable of Contents Using the Remote Control Battery SafetyTV/VCR Maintenance Replace the battery compartment lidHooking Up the TV/VCR Hook up your TV/VCR using one of the connections shownRF coaxial cable Not supplied Rod AntennaBent pin Hooking Up the TV/VCR cont’dCrooked Pin Straight Pin Cable PlugYou cannot set up channels if you are using a Cable Box Turning On the TV/VCRPress the Menu button. The screen shown below will appear Language Selection Press the Menu buttonPress the STATUS/EXIT button Wait for the TV/VCR to set up channels Automatic Channel SetupPress the PLAY/o button or the STOP/p button to select Adding/Deleting ChannelsRepeat steps 3-4 to add or delete other channels Programming of the channel you added or deleted will appearManual Clock Setting Setting the ClockCable Box users must set the clock manually Pages six-eightSetting the Clock cont’d Automatic PBS Channel Selection Setting the Clock cont’dWait for the TV/VCR to find the time NOW Searching flashes on the TV/VCR screenManual PBS Channel Selection Use the Number buttons to select your PBS station PRIM. SETUP. Then, press the F.FWD/ B button Daylight-Savings TimePress the PLAY/ button or the STOP/ button to select Time Zone Front Panel Rear Panel AC Power CordANTenna Jack Connect your antenna or cable here. Details are on page sixRemote Control Buttons STATUS/EXIT Button Menu ButtonREWind/ Button STOP/ ButtonAdjusting the Picture Controls Adjusting the Picture Controls cont’d Decrease IncreaseDecreased brightness If you select Status ON, then select Counter only OFF On-Screen Status DisplaysIf you select Status ON, then select Counter only on If you select Status OFFReminder ReminderPlaying Follow the steps below to play a tapeInsert a tape in the TV/VCR To stop recording, press the STOP/ button Tape Speeds RecordingYou cannot record if Defeat Recording is ON. Details are on One-Touch RecordingRerecording Tape Duplication TV/VCR is now in Line Input modeDaily Timer RecordingTimer Recording cont’d Timer Recording cont’d With the TV/VCR on, press the Menu button Timer recording information for the program in the lowestProgram REVIEW, then press the F.FWD/B button Gram Review and press the F.FWD/B buttonFollow the steps below to prevent accidental recording Defeat RecordingVCR SETUP, then press the F.FWD/B button Repeat PlayTV programming will appear while the tape is rewinding Insert a tape in the TV/VCR Press the Menu button B Repeat PlayRepeat Play cont’d Appear on the screen Real-Time Counter MemorySuper High Speed Searching LP/SLP Forward and Reverse Searching SP/LP/SLPViewing a Still Picture Viewing a Slow Motion PictureSmartLock To block ratings, follow the steps belowSmartlock menu will appear SmartLock cont’d Ratings will remain blocked even after a power failureRatings are defined on Example Specific Sub-ratingsUse the Number buttons to enter your old access code To change the access code, follow these stepsRating Explanations Blue Background VCR Program VCR Setup Caption ReminderPress the SLEEP/WAKE UP button Sleep TimerSLEEP. Then press the REWind/s button or FWD/B button to select 30 MINutes, 60 MINutesTimer Sleep Wake UP TV on ON-TIME Wake Up TimerCast with closed captions, you may choose to set the Volume Volume BarClosed Caption ExampleMenu Screen Closed Caption cont’d Standard Closed CaptionsHalf-screen text FM Radio Switching the AntennasAutomatic Operation Features Helpful Hints Helpful Hints cont’d Glossary Specifications Renewed Index Supplied Accessories