Philips NV-MV41GN Setting other Programmes in Succession, To check and cancel a Timer Programme

Page 14

Setting other Programmes in Succession

Repeat steps 1-9of Easy Timer Programming (page 13).

Programming a Timer Recording of a TV Programme Until its End

(Rec Mode Auto Change Function)

If the VCR determines that the remaining tape time is insufficient to record the programme to its end during a timer recording performed in the SP mode, this function automatically changes the Rec Mode to ensure that the whole programme will be recorded.

The Rec Mode will change as follows:

PAL system:

SP # LP

NTSC system:

SP # EP

• This function cannot change the recording mode to the

Timer recording for the same programme on the next week (Intelligent Timer)

When you wish to set the timer recording for programmes which will be recorded within 1 week and you have ever recorded the programmes before, you can record them soon with I-TIMER function without entering day and time by buttons. Select the desired setting from the list of timer programme recorded before. Please check the date and time carefully.

Preparations

•The VCR must be turned on, or in timer recording standby mode.

•Confirm that the TV is on and the VCR viewing channel is selected.

•Insert a video cassette with an intact erasure prevention tab.

1Press [I-TIMER] (24) to display the menu for Intelligent Timer on the TV screen.

• The list of the timer programmes which are recorded

EP mode for PAL system.

Depending on the remaining tape length, recording may be performed in the LP (EP) mode from the start. However, if the remaining tape time is still not sufficient in this case, the programme cannot be recorded to the end.

The tape length must be set correctly. (See page 8.) Some tapes may not work correctly.

If the recording mode changes from SP to LP during a timer recording, some brief picture distortion occurs at that point.

To Activate the Rec Mode Auto Change Function:

Press [REC MODE] (33) to select [A].

EASY PROGRAMMING

1. DATE

29WE

SELECT

2. CH

2

 

SET

 

3. ON TIME

20:02

 

 

 

 

 

 

4. OFF TIME

21:30

 

 

 

5. REC MODE

A

 

 

 

before appears.

2Press [43] (28) to select the timer programme which you want to record on the next week.

3Press [ENTER] (26).

•Timer Programme List screen appears.

4Press [TIMER (REC)] (14) to switch the VCR over to the timer recording standby mode.

Notes:

DAY

CH

 

ON

OFF

 

SU

4

 

19:10

19:55

EP

SU

14

 

15:00

16:00

SP

SU

25

 

10:30

11:00

A

SA

2

 

20:02

21:30

SP

FR

2

 

20:02

21:30

SP

WE

5

 

22:15

23:30

EP

 

 

 

 

 

 

 

 

 

 

 

 

ENTER

END : MENU

DATE CH ON OFF

15SA 2 10:30 11:00 SP 15SA 25 20:02 21:30 SP

16SU 25 10:30 11:00 A

:

:

:

:

:

:

:

:

:

:

SET : END : MENU

6. CATEGORY

 

TIMER

7. PUSH TIMER END : MENU

•Every time you press [REC MODE] (33), the indication changes in the following order:

SP # LP # EP # A # SP

•Up to 16 I-Timer Programmes can be memorized.

•When I-Timer Programmes are increased to more than 16, the oldest one is deleted.

To check and cancel a Timer Programme

Preparations

•The VCR must be turned on, or in timer recording standby mode.

•Confirm that the TV is on and the VCR viewing channel is selected.

1Press [CHECK] (23) or [TIMER CHECK] (41).

•The Timer Programme List screen appears.

2Press [CHECK] (23) or [TIMER CHECK] (41) repeatedly to select the program.

•Every time you press [CHECK]

(23) or [TIMER CHECK] (41), the

DATE

CH ON

OFF

 

SU-SA 25

10:30

11:00

A

cursor shifts below.

SU

14

15:00

16:00

SP

19WE

5

22:15

23:30

EP

23SA

2

20:02

21:30

SP

 

 

• Press [1] (28) to display the

28FR

A2

18:02

19:30

SP

30SU

4

19:10

19:55

EP

category. (When [JET

 

 

 

:

:

 

 

 

 

:

:

 

 

 

 

 

 

 

NAVIGATOR] is set to [ON].)

 

 

 

SET : END : MENU

 

 

 

 

 

 

 

Press [1] (28) again to make

 

 

 

 

 

 

the previous display appear.

 

 

 

 

 

 

3Press [CANCEL] (5) to cancel.

4Press [MENU] (9) to exit the On Screen Display.

Notes:

•If timer recording is not completed (due to insufficient tape or cancellation by the user), the programmed timer recording data will be cancelled from the memory by 4 A.M two days later.

However, if the timer recording function is activated at that time, the programmed timer recording data will not be cancelled.

•After you cancel the programmed timer recording data, the current Rec Mode is displayed during the stop mode.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Contents NV-MV41GNCondensation may form in the following cases For your safetyInserting Remote Control Batteries Input Select Timer CheckControls and Components PAUSE/SLOWConnections Setting the Remote Control to Operate Your TVConnection to a TV using the Audio/Video Input Socket Basic ConnectionsStoring TV Broadcasts in Your VCR Tuning the TV to Your VCRAuto Tuning Using the On Screen Display For New Zealand Pre-programmed TV Channels Australia onlyDirect Tuning Auto Tuning Using the On Screen Display For AustraliaManual Tuning Procedure Fine Tuning ProcedureTo Make Various Indicators Appear On Screen Display Setting the Clock of Your VCRSettings Using the On Screen Display Time Reset Function# Navi Check indicator # Clock Option SettingNavi Check indicator Playback Recording Operations Set OSD REC to ON. See Press REC 15 REC/OTR To reset the tape counterTo Display the Approximate Remaining Tape Time Press Stop 12 to stop1 6 . O C T 0 0 4 recordingTape REFRESH, and then press the Enter Recording from an external sourceRecording VCR To Suspend the Timer Recording Standby Mode Timer RecordingEasy Timer Programming Weekly and Daily Timer RecordingSetting other Programmes in Succession To check and cancel a Timer ProgrammeTo Set the Category Search FunctionsJet Navigator To Demonstrate the Jet Navigator Function To Check the Recorded Programming Data Time Stamp FunctionBefore Requesting Service Dirt on the video heads Adjusting the Playback PictureCrystal View Control Specifications
Top Page Image Contents