Auto Tuning Using the On Screen Display For Australia
Introduction
Auto Tuning using the On Screen Display should be performed according to the following method if necessary.
Preparations
•Confirm that the TV is on and the VCR viewing channel is selected.
•Turn on the VCR and select any programme position except A1 or A2.
Manual Tuning Procedure
If the VCR is not correctly tuned by Auto Tuning, follow the procedure below.
1 | Press [MENU] (9) to display the Main menu on the TV |
| screen. |
2 | Press [43] (28) to select [TUNER PRESET] then |
| press [ENTER] (26). |
3 | Press [43] (28) to select [CH] then select the channel |
| number you want to tune by pressing [2 1] (28). |
4 | Confirm that [CLEAR] is set to [OFF]. |
Operations
1Press [MENU] (9) to display the Main menu on the TV screen.
2Press [43] (28) to select [TUNER PRESET] then press [ENTER] (26).
3Confirm that [COUNTRY] is set to [AUSTRALIA].
MENU
CLOCK SET TUNER PRESET SYSTEM OPTION TAPE REFRESH
NAVI MEMORY 0PROG.
SELECT : 
, ENTER
END : MENU
MENU
CLOCK SET
TUNER PRESET SYSTEM OPTION TAPE REFRESH
NAVI MEMORY 0PROG.
SELECT : 
, ENTER
END : MENU
TUNER PRESET
CH 1 | [OFF] |
CLEAR | |
COUNTRY | [AUSTRALIA] |
AUTO TUNE |
|
SEARCH | [3] |
FINE |
|
5 Press [43] (28) to select [SEARCH] then press [2 1] |
(28)to start the Manual Tuning.
•If the desired TV station has not been tuned, press [2 1] (28) again.
•Press [MENU] (9) and repeat steps
|
| CH 2 | SEARCH 74 | ||
|
| ||||
CH 2 | SEARCH |
|
|
| END: MENU |
| END: MENU |
|
|
|
|
6Press [MENU] (9) three times to exit the On Screen Display.
Direct Tuning
Follow steps 1 to 4 of Manual Tuning Procedure.
SELECT:
END : MENU
4Press [43] (28) to select [AUTO TUNE] then press [2 1]
(28)to start the Auto Tuning.
•When Auto Tuning is completed, the On Screen Display disappears and programme position 1 is selected.
TUNER PRESET
CH 1 | [OFF] | ||||
CLEAR | |||||
COUNTRY | [AUSTRALIA] | ||||
AUTO TUNE | [3] | ||||
SEARCH | |||||
FINE |
| ||||
|
|
|
|
|
|
SELECT: |
|
|
|
| END : MENU |
AUTO TUNING
IN PROGRESS,
PLEASE WAIT.
CH 1 SEARCH 
100 END
: MENU
5Press [43] (28) to select [SEARCH].
6Press [Numeric] (3) to enter the number of the desired programme position.
•For other channels that require tuning, repeat steps 3, 4,
5, 6.
7Press [MENU] (9) twice to exit the On Screen Display.
Fine Tuning Procedure
Follow steps 1 to 4 of Manual Tuning Procedure.
5 Press [43] (28) to select |
[FINE] then press [2 1] (28) to |
obtain the best tuning condition. |
|
|
| The number displayed here | |
|
|
| is the number of channels | |
|
|
| still to be auto tuned. | |
Channels that can be received |
|
| ||
|
|
|
|
|
| VHF |
| UHF | CATV |
|
|
|
|
|
Australia |
| |||
|
|
|
|
|
Notes:
•Auto Tuning searches for TV stations from VHF minimum to UHF maximum and memorizes every tuned programme position. Other programme positions are skipped.
•Auto Tuning takes 5 or more minutes to complete its search.
• Press [ENTER] (26) to return the |
tuning to its former state. |
| CH 2 |
|
|
| AFC: ENTER |
6 Press [MENU] (9) to exit the On | FINE |
| : |
| END: MENU |
| |||||
|
|
|
|
| |
Screen Display. |
|
|
|
|
|
Blanking of Unused Programme Positions
Follow steps 1 to 3 of Manual Tuning Procedure.
4Press [43] (28) to select [CLEAR] then press [2 1] (28) to select [ON].
•Repeat steps 3, 4 for other unused programme positions to skip during the selection of programme positions.
•To cancel the blanking of a programme position, select that programme position then set [CLEAR] to [OFF].
5Press [MENU] (9) twice to exit the On Screen Display.
6