Philips NV-MV41GN Setting the Remote Control to Operate Your TV, Basic Connections

Page 4

Setting the Remote Control to Operate Your TV

You can operate the TVs of the manufacturers listed below with the remote control after setting it.

This setting procedure allows you to operate the TVs of some manufacturers using the supplied remote control.

Preparation

• Turn on the TV.

Operations

1Find the manufacturer number of your TV while referring to the following table.

2While holding down [TV-ON/OFF] (17) on the remote control, use [Numeric] (3) to enter the manufacturer number. This completes the settings for the TV manufacturer.

Be sure to enter the number in two digits. Example: 1 ) 01

3To confirm the correct settings were made, check whether the TV can be operated properly.

When a manufacturer has multiple numbers in the following table, try entering other numbers if the TV operations cannot be performed properly, and then select the optimal number.

Notes:

If you are using a Panasonic TV, this setting has already been made, and so you do not need to perform the above setting procedure. However, this remote control may not work with some Panasonic TVs.

Some TV models cannot be operated using this remote control (including all TVs non-remote compatible).

List of TVs Compatible with the VCR Remote Control

[Brand]

[Code]

 

 

Panasonic/National

01-04

 

 

SONY

05

 

 

TOSHIBA

06

 

 

JVC

07

 

 

HITACHI

08

 

 

MITSUBISHI

09, 10

 

 

SHARP

11

 

 

PHILIPS, SAMSUNG

12

 

 

NEC

13

 

 

SANYO

14

 

 

GOLDSTAR/LG

15, 16

 

 

SAMSUNG

17, 18

 

 

SANYO

19

 

 

Connections

This section shows you how to connect the VCR to an aerial, TV, etc.

Basic Connections

The following connections are required to record and play back the video cassette through the TV.

 

 

(1)

 

(3)

(2)

 

 

(4)

 

AC IN ~

2 IN

 

 

(6)

VIDEO2

 

AUDIO2

2 OUT

 

IN (AV1) OUT

RF

 

 

(5)

 

¢

 

(1) Aerial (Not supplied)

(6) AC Input socket (42)

(2) TV Set (Not supplied)

¢ To mains supply

(3)Aerial Connector

(4)RF IN socket (45)

(5)RF OUT socket (48)

Connection to a TV using the Audio/Video Input Socket:

Set the RF output channel of the VCR to [ss] (RF OFF) when the VCR is connected to the TV via the Audio/Video cable. (See page 5.)

 

 

 

 

(1)

 

 

(3)

(2)

 

 

 

(4)

(5)

 

 

 

 

(6)

(7)

 

 

 

 

 

AC IN ~

 

2 IN

 

 

 

 

 

 

(10)

VIDEO2

 

 

 

AUDIO2

2 OUT

 

 

 

IN (AV1) OUT

RF

 

 

 

(9)

 

(8)

 

 

 

 

 

¢

 

 

 

(1)

Aerial (Not supplied)

 

(8) RF OUT socket (48)

 

(2)

TV Set (Not supplied)

(9) VIDEO OUT (44)/

 

(3)

Aerial Connector

 

AUDIO OUT (47)

 

(4)

VIDEO IN

 

(10)AC Input socket (42)

 

(5)

AUDIO IN

 

¢ To mains supply

 

(6)Audio Cable/Video Cable (Not supplied)

(7)RF IN socket (45)

4

Image 4
Contents Contents NV-MV41GNInserting Remote Control Batteries For your safetyCondensation may form in the following cases Timer Check Controls and ComponentsInput Select PAUSE/SLOWSetting the Remote Control to Operate Your TV Connection to a TV using the Audio/Video Input SocketConnections Basic ConnectionsTuning the TV to Your VCR Auto Tuning Using the On Screen Display For New ZealandStoring TV Broadcasts in Your VCR Pre-programmed TV Channels Australia onlyAuto Tuning Using the On Screen Display For Australia Manual Tuning ProcedureDirect Tuning Fine Tuning ProcedureSetting the Clock of Your VCR Settings Using the On Screen DisplayTo Make Various Indicators Appear On Screen Display Time Reset FunctionNavi Check indicator Option Setting# Navi Check indicator # Clock Playback Recording To reset the tape counter To Display the Approximate Remaining Tape TimeOperations Set OSD REC to ON. See Press REC 15 REC/OTR Press Stop 12 to stop1 6 . O C T 0 0 4 recordingRecording VCR Recording from an external sourceTape REFRESH, and then press the Enter Timer Recording Easy Timer ProgrammingTo Suspend the Timer Recording Standby Mode Weekly and Daily Timer RecordingSetting other Programmes in Succession To check and cancel a Timer ProgrammeJet Navigator Search FunctionsTo Set the Category To Demonstrate the Jet Navigator Function To Check the Recorded Programming Data Time Stamp FunctionBefore Requesting Service Crystal View Control Adjusting the Playback PictureDirt on the video heads Specifications