Philips VR 969/02 Storing TV Channels, Easy Link function, Automatic channel search ATS Euro+

Page 10

3. STORING TV CHANNELS

In order that your video recorder can record

TV programmes, the TV channels (e.g. "ARD") must first be stored in the video recorder.

You can store up to 99 TV channels.

Your video recorder has a receiver of its own. This means it can be used independently of the TV set.

The "Easy Link" function

This function enables your video recorder to exchange information with the TV set. For this reason, also take note of the operating instructions that accompany your TV set.

The TV set and video recorder (tscart socket) must be connected using the special scart cable supplied and your TV set must have the "Easy Link" function.

!Switch on the TV set.

It is still possible at this stage to assign special functions to certain channel numbers. For further infor- mation, see the section "Manual search".

Automatic channel search (ATS Euro+)

The ATS Euro + function is not possible if the connect- ed TV set has "Easy Link".

The video recorder will make a search for all TV channels. It stores them in a logical sequence in the memory.

!Switch the TV set on and select the channel number for the video recorder.

"Press the button Son the video recorder.

¤The OSD page "LANGUAGE" appears on the screen. Select the display language desired.

"Pull out the mains plug and plug it back in again.

The video recorder automatically loads all of the TV

¤ channels stored in the TV set in the correct order.

This can take a few minutes.

The following display appears on screen:

"EASY LINKL Loading from TV – please wait",

"EASY LINK" appears in the video-recorder's

LANGUAGE

English

Deutsch

Français

Italiano

Español &Português

" % !

Nederlands

Dansk

Norsk

Svenska

Suomi

Confirm - OK

display.

Once all TV channels have been found, the video

recorder switches itself off.

$Select the desired display language. To do this, press the button Son the video recorder.

%The OSD page "LANGUAGE" appears on screen. Select the desired display language.

&Confirm the setting by pressing the button B. The OSD page "COUNTRY" appears on screen. Sel- ect your country.

/Confirm the setting by pressing the button B. "EASY LINK" appears briefly in the videorecorder display.

$Confirm by pressing the button B.

The OSD page "COUNTRY" appears on screen. Choose your country.

%Confirm by pressing the button B. The automatic tuning begins.

&Wait until all TV channels have been found. This may take a few minutes.

Once all TV channels have been found, a message, e.g. "ATS Euro+ ready 28 TV channels found" appears on screen. The automatic channel search is over.

/Press the button B. The OSD page "INSTALLATION MENU" appears on screen.

(Complete the setting by pressing the button l.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Contents Safety instructionsOperating Manual VR 969/02 Remote control BUTTONS, Controls and SocketsBack of the video recorder Buttons and display indicators on the front coverFront of the video recorder Buttons and connections behind the front cover Buttons and connections in the front coverInstallation HOW do I Install the Video Recorder ? Connecting the video recorderInserting the batteries into the remote control Connecting to the aerialSome notes on operation Connecting to the TV setConnecting to the mains supply If your TV set does not have a Scart Euro-AVConnecting to hifi equipment Connecting to a decoderConnecting to a satellite receiver Saving energyCursor buttons H/ Iup / down ButtonCursor buttons F/ Gleft / right Easy Link function Storing TV ChannelsAutomatic channel search ATS Euro+ 8D 8W Selecttv Assigning TV channels automatically Follow TVAssigning TV channels manually Manual search Fast forward wind and rewind Playing a Recorded CassetteVHS or VHS Playback Instant viewJOG/SHUTTLE functions Adjusting the picture sharpnessStill picture/super slow motion Slow motionSelecting the audio track, audio-mix Correcting picture interference. The cleaning functionSurround-sound playback Index search How do I know where I am currently on the tape?Intro-scan Assembly editing HOW can I Record Directly ?Longplay function Direct recording with TV sets without Easy Link functionErase protection HiFi stereo receptionWhat is HOW do I Programme a RECORDING?Programming with ShowView Programming with TXT pages Timer Programming Standard Timer How can I record from a satellite receiver? Few general notes on programmingHow can I check a Timer block ? How do I stop a Timer recording ?How can I clear or correct a Timer block ? Sorting TV programmes for Timer programming Audio dubbing Editing Video RecordingsAudio Dubbing Insert and insert-edit functionsPage Insert functions Switch the camcorder to still picture playback- pause Synchronous editing synchro-editVHS 20 PIN Synchro 5mm Insert-edit functions Methode 1 Insert VCRMethod 2 Insert CC Variant 1. The video recorder controls the camcorderProgramme edit functions Rearranging individual scenesRecording all scenes Deleting individual scenesPreview of scenes in the editing sequence Totally deleting the editing sequenceAdditional Functions of Your Video Recorder Checking/setting time and date on video recorderPersonal preferences Special settings for the video recorder and TV set TXT decoder Reading TXT with the video recorder How can I read TXT?Externally controlled Timer recording Interface RSRecording from another video source Audio only recordSwitching between VCR 1 and VCR View modeTV monitor function Playback via the aerial cable Remote control of TV sets Switching the built-in modulator on and offNumeric button TV make Safety instructions/notes PAL SecamBefore YOU Call a Technician ProblemPossible cause Technical data Technical DATA, AccessoriesAccessories supplied Philips SYNCHRO-EDIT Cable NEW Edit
Top Page Image Contents