Philips VRA633AT owner manual 2Find your TV code, Press the Mute button

Page 22

22 Setting the Remote to Operate a TV

Your VCR remote control may operate your TV. If the remote control doesn’t operate your TV now, follow the steps below.

1

Point the remote control at your TV and press the TV button. Then, press the POWER button. If your TV turns on or off, try the other TV buttons (see pages 24-25). If your TV doesn’t turn on or off, or if the other buttons don’t work, go to step 2.

1&6

	POWER	VCR/TV
4	VCR	TV
4		PLAY

REW

STOP

2Find your TV code.

EJECT

CBL/DBS

F.FWD

2

MENU

STATUS/EXIT

CLEAR

Find the brand of your TV on the list below, and remem- ber the two-digit number beside it.

TV CODES

EMERSON	. . . . . .14	PHILCO	. . . . . .14
FISHER	. . . . . .11	PHILIPS	. . . . . .01
GE	. . . . . .10	PHILIPS MAGNAVOX.	.01, 02, 03
GOLDSTAR	. . . . . .04	QUASAR	. . . . . .07
HITACHI	. . . . . .12	RCA	. . . . . .10
JVC	. . . . . .05	SAMSUNG	. . . . . .17
MAGNAVOX	01, 02, 03	SANYO	. . . . . .11
MARANTZ	. . . . . .13	SEARS	. . .08, 11
MITSUBISHI	. . . . . .13	SHARP	. . . . . .16
MONTGOMERY WARD . . . .14		SONY	. . . . . .09
PANASONIC	. . . . . .07	TOSHIBA	. . . . . .08
PANASONIC-GAOO .	. . . . . .07	ZENITH	. . .06, 15

3

Press the MUTE button.

4

5	1	2	3
	4	5	6
	7	8	9
	VCR PLUS+/ENTER		ALT. CH
		0
	SPEED	TIME SEARCH PAUSE/STILL
	REC/OTR	MEMORY	SLOW

CH

VOL

MUTE3

Within 30 seconds, press the TV button.

5

Within 30 seconds, press the Number buttons to enter the two-digit code for your TV brand. For example, if you have a Zenith TV, press Number buttons 0, 6.

6

Repeat step 1. If the remote control works your TV, you’re fin- ished. If the remote control still doesn’t work your TV, repeat steps 3-5, using a different code for your brand (if available).

There is no guarantee that the

remote will work your TV.

Helpful Hints

•The remote control may only operate some features of your TV. For exam- ple, the remote control may turn on the TV power, but it may not change channels at the TV.

•If you can not change the channels at the TV using the Number but- tons, press the VCR PLUS+/ENTER button after you press the Number buttons. It may change channels at the TV.

•When you replace the batteries in the remote control, you must pro- gram the remote control again.

•Remember to point the remote con- trol toward the TV during steps 1-6.

Image 22

Contents VRA633AT This bolt of lightning indi- cates uninsulated material Dear Philips Magnavox product ownerFor Customer Use Model No Serial NoSafety Precautions FeaturesIntroduction Table of Contents VCR maintenance Putting Batteries in the Remote ControlUsing the Remote Control Removing the Plastic Cover from the Front PanelHookups without a Cable Box/Direct Broadcast System Disconnect the antenna or cable from your TVHookups without a Cable Box/Direct Broadcast System cont’d Plug in the TV and the VCRConnections Hookups with a Cable Box/Direct Broadcast SystemRecording/Viewing Any Channel Cable Box/DBS Recording One Channel/Watching AnotherTV’s Antenna Hookups with a Stereo TV 2Turn on the TV Turning on Your VCRPress the Menu button. The display shown below will appear Automatic Channel Setup Press the VCR button Press the Menu buttonAutomatic Channel Setup cont’d Adding/Deleting ChannelsReviewing Memorized Channels Press the STATUS/EXIT button once or twice to exitManual Clock Setting Setting the ClockDo each step within 60 seconds of the previous step Setting the Clock cont’d Automatic Clock Setting Press the VCR button, then press the Menu buttonTime Zone Daylight-Savings Time Press the VCR buttonLanguage Selection When Child Lock is activated Child Lock2Find your TV code Press the Mute button2Find Your codeEject Button Remote Control ButtonsVOLume o/p Button Press to adjust the volume of your TV VCR ButtonVCR PLUS+/ENTER Button REWind/ ButtonMenu If you select Status ON, then select Counter only on On-Screen Status DisplaysStatus Display example only If you select Status ON, then select Counter only OFFCassette Compartment Timer LightVCR Display Panel VCR LightFront Panel Rear Panel Read and follow the steps below to play a tape Playing1Turn on the TV 2Insert a tape in the VCR VCR light does not appear, press the VCR/TV button once RecordingIf the VCR light appears on the display panel, go to . If RECord light will appearRecording One Channel/Watching Another One-Touch Recording Press the VCR button, then press the CHannel o/p butTimer Recording DailyTimer Recording cont’d Timer Recording cont’d Tape SpeedsChecking or Cancelling Timer Recordings Channels Setting Up the VCR Plus+ Programming SystemCall Letters Setting Up the VCR Plus+ Programming System cont’d Examine the lists onTimer Recording with the VCR Plus+ Programming System Press the STATUS/EXIT button. Program WAS COM See page 52 for more hintsRerecording Tape Duplication RF coaxial cableRepeat Play VCR SET UP, then press the F.FWD/B buttonPress the F.FWD/B button so that on appears beside Real-Time Counter Memory Time Search Press the VCR button Press the Time Search buttonSuper High Speed Searching LP/SLP Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Viewing a Still PictureAutomatic Operation Features Specifically… Multi-Channel Television Sound SystemUnderstanding On-Screen Displays MonitorMulti-Channel Television Sound System cont’d Hi-Fi Stereo Sound System → Hifi Mono To END Push ExitHi-Fi Stereo Sound System cont’d Please see additional notes onHelpful Hints Helpful Hints cont’d Glossary Cable Box/DBS Output Channel 03 orSpecifications Limited Warranty Model # Serial #Index Page Page Supplied Accessories