Philips VRA633AT owner manual Timer Recording with the VCR Plus+ Programming System

Page 40

40 Timer Recording with the VCR Plus+ Programming System

Follow these steps to set a timer recording with the PlusCode programming numbers in your TV guide. Before you begin:

●Set up the channels at the VCR (page 12).

●Set up the VCR Plus+ and Cable/TV channel numbers (pages 38-39).

●Set the clock (pages 15-18).

●Put a tape in the VCR.

●Make sure the VCR light appears on the display panel. If it does not, press the VCR/TV button once.

Do each step within 60 seconds of the previous step.

1

Press the VCR button.

2

Press the VCR PLUS+/ENTER button.

VCR PLUS+ PROG.

PLUS CODE : – – – – – – – –

TO END PUSH EXIT

3

Press the Number buttons to enter the PlusCode pro- gramming number of the program you wish to record. Then, press the VCR PLUS+/ENTER button.

VCR PLUS+ PROG.

PLUS CODE : 13285 – – –

TO SET PUSH VCR+

TO CORRECT PUSH CLEAR

TO END PUSH EXIT

4

Press the PLAY/o button or the STOP/p button to select a ONCE, DAILY, or WEEKLY recording. Then, press the F.FWD/B button.

●ONCE: The VCR will record a TV program on any day you choose, up to 12 months away.

●DAILY: The VCR will record a program every day from Monday to Friday – starting at the same time and recording for the same length of time.

●WEEKLY: The VCR will record a program on the same day, at the same time, and for the same length of time every week.

VCR PLUS+ PROG.

→ONCE DAILY WEEKLY

SELECT op CHOOSE B

TO END PUSH EXIT

POWER VCR/TV EJECT

1

VCR

TV

 

CBL/DBS

 

 

PLAY

 

 

4

 

REW

STOP

 

F.FWD

 

MENU

STATUS/EXIT

CLEAR

 

3

1

2

3

 

 

4

5

6

CH

 

 

 

7

8

9

 

 

 

VCR PLUS+/ENTER

ALT. CH

 

0VOL

2

SPEED

TIME SEARCH

PAUSE/STILL

 

 

REC/OTR

MEMORY

SLOW

MUTE

Helpful Hints

•If ERROR flashes on the screen when you select a DAILY recording at step 4, the program you selected takes place on a weekend. Select ONCE or WEEKLY for this program.

•CODE ERROR may flash on the screen after step 3 if you enter an incorrect PlusCode programming number (for example, one that is too short). The previous screen will appear. Enter the correct PlusCode programming num- ber.

•If CLASH flashes on the screen after step 3, the timer recording you just programmed and another timer recording overlap. The previous screen will appear. Enter a different PlusCode programming number or cancel the overlapping timer recording.

•If the VCR PLUS+ CROSS REF. MAP reappears after step 3, the VCR PLUS + channel number for the recording you entered was higher than 99. In this

case, enter the correct CABLE/TV chan- nel in the map. Then, press the MENU button and continue from step 4.

Page 39 Page 41
Image 40
Page 39 Page 41
Contents VRA633AT Dear Philips Magnavox product owner For Customer UseThis bolt of lightning indi- cates uninsulated material Model No Serial NoSafety Precautions FeaturesIntroduction Table of Contents Putting Batteries in the Remote Control Using the Remote ControlVCR maintenance Removing the Plastic Cover from the Front PanelHookups without a Cable Box/Direct Broadcast System Disconnect the antenna or cable from your TVHookups without a Cable Box/Direct Broadcast System cont’d Plug in the TV and the VCRConnections Hookups with a Cable Box/Direct Broadcast SystemRecording/Viewing Any Channel Cable Box/DBS Recording One Channel/Watching AnotherTV’s Antenna Hookups with a Stereo TV 2Turn on the TV Turning on Your VCRPress the Menu button. The display shown below will appear Automatic Channel Setup Press the VCR button Press the Menu buttonAutomatic Channel Setup cont’d Adding/Deleting ChannelsReviewing Memorized Channels Press the STATUS/EXIT button once or twice to exitManual Clock Setting Setting the ClockDo each step within 60 seconds of the previous step Setting the Clock cont’d Automatic Clock Setting Press the VCR button, then press the Menu buttonTime Zone Daylight-Savings Time Press the VCR buttonLanguage Selection When Child Lock is activated Child Lock2Find your TV code Press the Mute button2Find Your codeRemote Control Buttons VOLume o/p Button Press to adjust the volume of your TVEject Button VCR ButtonVCR PLUS+/ENTER Button REWind/ ButtonMenu On-Screen Status Displays Status Display example onlyIf you select Status ON, then select Counter only on If you select Status ON, then select Counter only OFFTimer Light VCR Display PanelCassette Compartment VCR LightFront Panel Rear Panel Read and follow the steps below to play a tape Playing1Turn on the TV 2Insert a tape in the VCR Recording If the VCR light appears on the display panel, go to . IfVCR light does not appear, press the VCR/TV button once RECord light will appearRecording One Channel/Watching Another One-Touch Recording Press the VCR button, then press the CHannel o/p butTimer Recording DailyTimer Recording cont’d Timer Recording cont’d Tape SpeedsChecking or Cancelling Timer Recordings Channels Setting Up the VCR Plus+ Programming SystemCall Letters Setting Up the VCR Plus+ Programming System cont’d Examine the lists onTimer Recording with the VCR Plus+ Programming System Press the STATUS/EXIT button. Program WAS COM See page 52 for more hintsRerecording Tape Duplication RF coaxial cableRepeat Play VCR SET UP, then press the F.FWD/B buttonPress the F.FWD/B button so that on appears beside Real-Time Counter Memory Time Search Press the VCR button Press the Time Search buttonSpecial Effects Playback Forward and Reverse Searching SP/LP/SLPSuper High Speed Searching LP/SLP Viewing a Still PictureAutomatic Operation Features Multi-Channel Television Sound System Understanding On-Screen DisplaysSpecifically… MonitorMulti-Channel Television Sound System cont’d Hi-Fi Stereo Sound System → Hifi Mono To END Push ExitHi-Fi Stereo Sound System cont’d Please see additional notes onHelpful Hints Helpful Hints cont’d Glossary Cable Box/DBS Output Channel 03 orSpecifications Limited Warranty Model # Serial #Index Page Page Supplied Accessories
Top Page Image Contents