Philips VRA633AT owner manual Timer Recording cont’d

Page 35

Timer Recording (cont’d) 35

4

Use the Number buttons (1 - 8) to select a slot in which to store the timer recording. There are eight slots. Numbers for open slots will flash on the screen.

NOTE: If you enter a number for a slot that has already been used to store a timer recording, PREVIOUSLY SET PROGRAM will appear on the screen briefly. Information about the program in that slot will appear on the screen. If this happens, press the STATUS/EXIT button, then select another number.

5

Use the Number buttons to enter the channel you want to record.

●Cable Users, enter channel numbers as a two-digit number for the quickest results. For example, to select channel 6, press

0,6. If you only press the Number 6 button, channel 6 will be selected after a brief delay. There also may be a brief delay when you select channels 10, 11, and 12. If you want to select chan- nels 100 and above, enter channel numbers as a three-digit number. For example, to select channel 117, press 1, 1, 7. Antenna Users, enter channel numbers as a two-digit number for the quickest results. For example, to select channel 5, press 0,5. If you only press the Number 5 button, channel 5 will be selected after a brief delay.

●If you are recording from line input, press 0,0 to select AV REAR.

●If you are using a Cable Box/DBS, select the Cable Box/DBS output channel (03 or 04). Set the Cable Box/DBS to the chan- nel you want to record. Leave the Cable Box/DBS on for the timer recording. See page eight for details.

4-7

POWER

VCR/TV

 

EJECT

VCR

TV

 

CBL/DBS

 

PLAY

 

 

REW

 

 

 

F.FWD

 

STOP

 

 

MENU

STATUS/EXIT

CLEAR

1

2

 

3

 

4

5

 

6

CH

 

 

7

8

 

9

 

VCR PLUS+/ENTER

 

ALT. CH

 

0

 

 

VOL

 

 

 

 

SPEED TIME SEARCH

PAUSE/STILL

REC/OTR

MEMORY

SLOW

MUTE

6

Press two Number buttons for the hour you want the recording to begin. Press two Number buttons for the minute you want the recording to begin. Press 1 for AM or 2 for PM. For example, for 9:30 PM, press 09, 30, 2.

ONE TIME PROGRAM

PROGRAM

1

CHANNEL

10

TIME ON

– – : – –

TO CORRECT PUSH CLEAR

TO END PUSH EXIT

7

Follow the instructions in step 6 to enter the recording’s stop time. (AM or PM will be set automatically.)

ONE TIME PROGRAM

PROGRAM

1

CHANNEL

10

TIME ON

09:30 PM

TIME OFF

– – : – –

TO CORRECT PUSH CLEAR

TO END PUSH EXIT

Helpful Hints

•Entries that do not match the VCR’s clock or calendar will cause a ques- tion mark to appear on the screen.

•If you are recording from line input, connect the audio and video cables to the AUDIO IN and VIDEO IN jacks on the back of the VCR. (Please see illustration on page 42.)

Instructions continue on page 36.

Page 34 Page 36
Image 35
Page 34 Page 36
Contents VRA633AT Model No Serial No Dear Philips Magnavox product ownerFor Customer Use This bolt of lightning indi- cates uninsulated materialIntroduction FeaturesSafety Precautions Table of Contents Removing the Plastic Cover from the Front Panel Putting Batteries in the Remote ControlUsing the Remote Control VCR maintenanceDisconnect the antenna or cable from your TV Hookups without a Cable Box/Direct Broadcast SystemPlug in the TV and the VCR Hookups without a Cable Box/Direct Broadcast System cont’dRecording/Viewing Any Channel Hookups with a Cable Box/Direct Broadcast SystemConnections TV’s Antenna Recording One Channel/Watching AnotherCable Box/DBS Hookups with a Stereo TV Press the Menu button. The display shown below will appear Turning on Your VCR2Turn on the TV Press the VCR button Press the Menu button Automatic Channel SetupAdding/Deleting Channels Automatic Channel Setup cont’dPress the STATUS/EXIT button once or twice to exit Reviewing Memorized ChannelsDo each step within 60 seconds of the previous step Setting the ClockManual Clock Setting Setting the Clock cont’d Press the VCR button, then press the Menu button Automatic Clock SettingTime Zone Press the VCR button Daylight-Savings TimeLanguage Selection Child Lock When Child Lock is activatedPress the Mute button 2Find your TV codeYour code 2FindVCR Button Remote Control ButtonsVOLume o/p Button Press to adjust the volume of your TV Eject ButtonMenu REWind/ ButtonVCR PLUS+/ENTER Button If you select Status ON, then select Counter only OFF On-Screen Status DisplaysStatus Display example only If you select Status ON, then select Counter only onVCR Light Timer LightVCR Display Panel Cassette CompartmentFront Panel Rear Panel 1Turn on the TV 2Insert a tape in the VCR PlayingRead and follow the steps below to play a tape RECord light will appear RecordingIf the VCR light appears on the display panel, go to . If VCR light does not appear, press the VCR/TV button onceRecording One Channel/Watching Another Press the VCR button, then press the CHannel o/p but One-Touch RecordingDaily Timer RecordingTimer Recording cont’d Tape Speeds Timer Recording cont’dChecking or Cancelling Timer Recordings Call Letters Setting Up the VCR Plus+ Programming SystemChannels Examine the lists on Setting Up the VCR Plus+ Programming System cont’dTimer Recording with the VCR Plus+ Programming System See page 52 for more hints Press the STATUS/EXIT button. Program WAS COMRF coaxial cable Rerecording Tape DuplicationPress the F.FWD/B button so that on appears beside VCR SET UP, then press the F.FWD/B buttonRepeat Play Real-Time Counter Memory Press the VCR button Press the Time Search button Time SearchViewing a Still Picture Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLPAutomatic Operation Features Monitor Multi-Channel Television Sound SystemUnderstanding On-Screen Displays Specifically…Multi-Channel Television Sound System cont’d → Hifi Mono To END Push Exit Hi-Fi Stereo Sound SystemPlease see additional notes on Hi-Fi Stereo Sound System cont’dHelpful Hints Helpful Hints cont’d Cable Box/DBS Output Channel 03 or GlossarySpecifications Model # Serial # Limited WarrantyIndex Page Page Supplied Accessories
Top Page Image Contents