Philips VRA633AT owner manual Checking or Cancelling Timer Recordings

Page 37

Timer Recording (cont’d) 37

Checking or Cancelling Timer Recordings

1

With the VCR on and in VCR position (the VCR light will appear on the display panel), press the VCR button, then press the

MENU button.1

2

Press the PLAY/o button or the STOP/p button to select PROGRAM, then press the F.FWD/B button.

3

Press the PLAY/o button or the STOP/p button to select PROGRAM REVIEW, then press the F.FWD/B button. The timer recording information for the program in the lowest numbered slot will appear on the screen. If no timer recordings are set, nothing will happen when you press the F.FWD/B button.

2-4

POWER

VCR/TV

 

EJECT

VCR

TV

 

CBL/DBS

 

PLAY

 

 

REW

 

 

F.FWD

 

STOP

 

 

MENU

STATUS/EXIT

CLEAR

1

2

3

 

4

5

6

CH

 

7

8

9

 

VCR PLUS+/ENTER

ALT. CH

0VOL

SPEED TIME SEARCH PAUSE/STILL

REC/OTR MEMORY SLOW MUTE

5

4

Press the F.FWD/B button repeatedly to review all pro- grammed timer recordings. If you don’t press the F.FWD/B button within 10 seconds, the VCR will automatically display infor- mation about the next programmed timer recording. This will continue until all timer recordings have been displayed. Then the menu will disappear.

5

To cancel the timer recording displayed, press the CLEAR button. Either the display will disappear or information about other timer recordings will appear. If you do not press any other buttons, the display will disappear after all timer recordings have been displayed.

6

Repeat steps 1 - 4 to make sure you have cleared the cor- rect timer recording.

Helpful Hints

•CLASH may flash on the screen when you finish setting a timer recording. This means that the timer recording you just programmed and another timer record- ing overlap. The current timer recording will not take place. You may choose to cancel the overlapping timer recording.

•To stop a started timer recording, press the STOP/EJECT button on the VCR.

•If the power fails for more than one minute, programmed timer recordings will be lost. Reset the clock before reset- ting the timer recordings.

•If the preset time for a timer recording comes up during an OTR, the OTR has priority. A message will remind you when the timer recording was scheduled to begin. You may let the OTR continue; the timer recording will not take place. Or, stop the OTR and turn off the VCR immediately. The timer recording will take place if you turn off the VCR

before the timer recording’s scheduled start time.

See page 52 for more hints.

Page 36 Page 38
Image 37
Page 36 Page 38
Contents VRA633AT For Customer Use Dear Philips Magnavox product ownerThis bolt of lightning indi- cates uninsulated material Model No Serial NoSafety Precautions FeaturesIntroduction Table of Contents Using the Remote Control Putting Batteries in the Remote ControlVCR maintenance Removing the Plastic Cover from the Front PanelDisconnect the antenna or cable from your TV Hookups without a Cable Box/Direct Broadcast SystemPlug in the TV and the VCR Hookups without a Cable Box/Direct Broadcast System cont’dConnections Hookups with a Cable Box/Direct Broadcast SystemRecording/Viewing Any Channel Cable Box/DBS Recording One Channel/Watching AnotherTV’s Antenna Hookups with a Stereo TV 2Turn on the TV Turning on Your VCRPress the Menu button. The display shown below will appear Press the VCR button Press the Menu button Automatic Channel SetupAdding/Deleting Channels Automatic Channel Setup cont’dPress the STATUS/EXIT button once or twice to exit Reviewing Memorized ChannelsManual Clock Setting Setting the ClockDo each step within 60 seconds of the previous step Setting the Clock cont’d Press the VCR button, then press the Menu button Automatic Clock SettingTime Zone Press the VCR button Daylight-Savings TimeLanguage Selection Child Lock When Child Lock is activatedPress the Mute button 2Find your TV codeYour code 2FindVOLume o/p Button Press to adjust the volume of your TV Remote Control ButtonsEject Button VCR ButtonVCR PLUS+/ENTER Button REWind/ ButtonMenu Status Display example only On-Screen Status DisplaysIf you select Status ON, then select Counter only on If you select Status ON, then select Counter only OFFVCR Display Panel Timer LightCassette Compartment VCR LightFront Panel Rear Panel Read and follow the steps below to play a tape Playing1Turn on the TV 2Insert a tape in the VCR If the VCR light appears on the display panel, go to . If RecordingVCR light does not appear, press the VCR/TV button once RECord light will appearRecording One Channel/Watching Another Press the VCR button, then press the CHannel o/p but One-Touch RecordingDaily Timer RecordingTimer Recording cont’d Tape Speeds Timer Recording cont’dChecking or Cancelling Timer Recordings Channels Setting Up the VCR Plus+ Programming SystemCall Letters Examine the lists on Setting Up the VCR Plus+ Programming System cont’dTimer Recording with the VCR Plus+ Programming System See page 52 for more hints Press the STATUS/EXIT button. Program WAS COMRF coaxial cable Rerecording Tape DuplicationRepeat Play VCR SET UP, then press the F.FWD/B buttonPress the F.FWD/B button so that on appears beside Real-Time Counter Memory Press the VCR button Press the Time Search button Time SearchForward and Reverse Searching SP/LP/SLP Special Effects PlaybackSuper High Speed Searching LP/SLP Viewing a Still PictureAutomatic Operation Features Understanding On-Screen Displays Multi-Channel Television Sound SystemSpecifically… MonitorMulti-Channel Television Sound System cont’d → Hifi Mono To END Push Exit Hi-Fi Stereo Sound SystemPlease see additional notes on Hi-Fi Stereo Sound System cont’dHelpful Hints Helpful Hints cont’d Cable Box/DBS Output Channel 03 or GlossarySpecifications Model # Serial # Limited WarrantyIndex Page Page Supplied Accessories
Top Page Image Contents