Philips VRA601AT owner manual Turning on Your VCR, 2Turn on the TV

Page 11

Before turning on your VCR, make sure batteries are in the remote control and the VCR and TV are connected correctly.

●You can not program channels if you are using a Cable Box or a Direct Broadcast System.

1

Press the POWER button. The VCR/TV light and the POWER light will appear on the display panel.

2

Turn on the TV. Set it to the same channel as the CH3/CH4 switch on the back of the VCR. The display shown below will appear. (If the display does not appear, check your hookups, then follow the steps on page 12 to set up channels and page 17 to select a language.)

SELECT op
→ ENGLISH	ON
ESPAÑOL

MAKE SELECTION OR

PUSH MENU TO CONTINUE

Turning on Your VCR 11

2Turn on the TV.

1	POWER		VCR/TV	EJECT
1	1	2	3		5
	4	5	6
		0		CHANNEL
	7	8	9
4	SPEED	TIME SEARCH		MEMORY
4	MENU	STATUS/EXIT	CLEAR	SLOW
	REWIND	/PLAY		F.FWD	3
	REC/OTR	/STOP		PAUSE/STILL	3

3

Within 60 seconds, press the PLAY/o button or the STOP/p button to select English or Spanish on-screen displays and menus.

4

Press the MENU button. The display shown below will appear.

CONNECT ANTENNA OR CABLE

TO VCR

THEN . . .

PUSH CH UP KEY

OR . . .

FOR PLAY ONLY – PUSH STOP

5

Within 60 seconds, press the CHANNEL o button to begin automatic channel programming. AUTO CH PRO- GRAMMING IN PROCESS PLEASE WAIT will appear on the screen. The VCR will memorize all available channels. When all channels are programmed, CHANNELS ARE SET will appear on the screen briefly, then TV programming will appear.

Now, when you press the CHANNEL o/p buttons, you’ll only scan through channels that you receive.

Helpful Hints

•To skip this feature and play a tape immediately, insert a tape with its record tab removed. Or, to skip step 3, press the MENU button. All on- screen displays will be in English. To skip step 5, press the STOP/p but- ton. Channels will not be pro- grammed, and CHANNELS NOT SET will appear on the screen.

•If you try to program channels when there is no antenna or cable connected to the VCR, programming will appear to take place, but even- tually a NO TV SIGNALS message will appear. Connect an antenna or cable to the VCR’s ANT(enna) IN Jack and press the CHANNEL o button again. You may need to fol- low the steps on page 12.

Image 11

Contents VRA601AT Model No Serial No Dear Philips Magnavox product ownerFor Customer Use This bolt of lightning indi- cates uninsulated materialIntroduction FeaturesSafety Precautions Table of Contents Removing the Plastic Cover from the Front Panel Before Using Your VCRPutting Batteries in the Remote Control VCR maintenanceDisconnect the antenna or cable from your TV Hookups Without a Cable Box/Direct Broadcast SystemPlug in the TV and the VCR Hookups Without a Cable Box/Direct Broadcast System cont’dRecording/Viewing Any Channel Hookups With a Cable Box/Direct Broadcast SystemConnections TV’s Antenna Recording One Channel/Watching AnotherVideo Cable Hookups With a Stereo TVPress the Menu button. The display shown below will appear Turning on Your VCR2Turn on the TV Press the Menu button Automatic Channel SetupAdding/Deleting Channels Automatic Channel Setup cont’dPress the STATUS/EXIT button once or twice to exit Reviewing Memorized ChannelsYou make each entry within 60 seconds of the previous entry Follow the steps below to set your VCR’s clock. Make sureDaylight-Savings Time Language Selection Remote Control Buttons Clear Button Remote Control Buttons cont’dEject Button Press to eject the tapeIf you select Status ON, then select Counter only OFF On-Screen Status DisplaysStatus Display example only If you select Status ON, then select Counter only onVCR Display Panel Front Panel Rear Panel 1Turn on the TV 2Insert a tape in the VCR PlayingRead and follow the steps below to play a tape RECord light will appear RecordingInsert a tape with its record tab intact in the VCR Recording One Channel/Watching Another One-Touch Recording Daily Timer RecordingDo each step within 60 seconds of the previous step Timer Recording cont’d Tape Speeds Timer Recording cont’dChecking or Cancelling Timer Recordings RF coaxial cable Rerecording Tape DuplicationPress the F.FWD/B button so that on appears beside Repeat PlayPress the PLAY/o button or the STOP/p button to select Real-Time Counter Memory Press the Time Search button Time SearchViewing a Still Picture Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLPAutomatic Operation Features Monitor Multi-Channel Television Sound SystemUnderstanding On-Screen Displays Specifically…Multi-Channel Television Sound System cont’d Hi-Fi Stereo Sound System Please see additional notes on Hi-Fi Stereo Sound System cont’dHIFI. on will appear to the right of Hifi on the screen Helpful Hints Helpful Hints cont’d Cable Box/DBS Output Channel 03 or GlossarySpecifications Model # Serial # Limited WarrantyAutomatic PowerRemote control TimerSupplied Accessories