Philips VRA411AT owner manual Hookups With a Stereo TV, Jack

Page 10

10 Hookups With a Stereo TV

			antenna or
			1 ANT(enna)cable to
		ANT	IN Jack
		IN
AUDIO
OUT	IN	OUT
		OUT
VIDEO		CH3 CH4
VIDEO
VIDEO (yellow) and		2
AUDIO (white) OUT Jacks		2	Video Cable
AUDIO (white) OUT Jacks

3			Audio Cable

●Audio and Video cables are not supplied.

1

Connect the antenna or cable to the ANT(enna) IN Jack on the back of the VCR.

2

Connect a video cable to the yellow VIDEO OUT Jack on the back of the VCR. Then, connect the other end of the video cable to the VIDEO IN Jack on your TV.

3

Connect an audio cable to the white AUDIO OUT Jack on the back of the VCR. Then, connect the other end of the audio cable to the AUDIO IN Jack on your TV.

(If your TV has Right and Left AUDIO IN Jacks, you must use a “Y” splitter audio cable as illustrated to deliver audio to the TV’s right and left channels.)

4

Turn on your TV, making sure it is in Line Input mode. Please refer to your TV owner’s manual for details.

Audio and Video IN Jacks on TV

Helpful Hint

•This hookup will not give you stereo sound. To get stereo sound, use the connections on pages six - seven and select the channel to be viewed at the TV (with the VCR turned off).

Image 10

Contents VRA411AT This bolt of lightning indi- cates uninsulated material Dear Philips Magnavox product ownerFor Customer Use Model No Serial NoSafety Precautions FeaturesIntroduction Table of Contents VCR maintenance Putting Batteries in the Remote ControlUsing the Remote Control Removing the Plastic Cover from the Front PanelHookups Without a Cable Box/Direct Broadcast System Disconnect the antenna or cable from your TVHookups Without a Cable Box/Direct Broadcast System cont’d Plug in the TV and the VCRConnections Cable Signal RF coaxialHookups With a Cable Box/Direct Broadcast System Recording/Viewing Any ChannelRecording One Channel/Watching Another Cable SignalConnect a Cable signal to the VCR’s ANTenna in Jack Cable Box/DBSHookups With a Stereo TV Jack2Turn on the TV Press the VCR button, then press the Power buttonTurning on Your VCR Press the Menu button. The display shown below will appearAutomatic Channel Setup Press the VCR button Press the Menu buttonAutomatic Channel Setup cont’d Adding/Deleting ChannelsReviewing Memorized Channels Press the STATUS/EXIT button once or twice to exitSetting the Clock SET CLOCK, then press the F.FWD/ B buttonDaylight-Savings Time Press the VCR buttonLanguage Selection Remote Control Buttons Press again to resume normal playback REWind/ ButtonSTOP/p Button MenuIf you select Status ON, then select Counter only on On-Screen Status DisplaysStatus Display example only If you select Status ON, then select Counter only OFFVCR Display Panel Front Panel Rear Panel Read and follow the steps below to play a tape Playing1Turn on the TV 2Insert a tape in the VCR If the VCR light appears on the display panel, go to . If RecordingVCR light does not appear, press the VCR/TV button once Recording One Channel/Watching Another VCR light will disappear from the VCR’s display panelOne-Touch Recording Press the VCR button, then press the Menu button Timer RecordingDo each step within 60 seconds of the previous step DailyTimer Recording cont’d Timer Recording cont’d Tape SpeedsTimer recording information for the program in the lowest Checking or Cancelling Timer RecordingsProgram REVIEW, then press the F.FWD/B button Rerecording Tape Duplication Repeat Play Press the F.FWD/B button so that on appears besidePress the STATUS/EXIT button to see the status display Clear button to reset the real-time counter to zeroReal-Time Counter Memory While the status display is on the screen, pressTime Search Press the VCR button Press the Time Search buttonSuper High Speed Searching LP/SLP Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Viewing a Still PictureAutomatic Operation Features Helpful Hints Helpful Hints cont’d Glossary Cable Box/DBS Output Channel 03 orSpecifications Limited Warranty Model # Serial #Index Supplied Accessories