Philips VRA411AT owner manual Playing, Read and follow the steps below to play a tape

Page 24

24 Playing

Read and follow the steps below to play a tape.

1

Turn on the TV and set it to channel 3 or 4, whichever channel the CH3/CH4 switch on the back of the VCR is set to.

1Turn on the TV.

2Insert a tape in the VCR.

2

Insert a tape in the VCR. The PWR., VCR, and Cassette-Inside lights will appear on the display panel. If the tape’s record tab has been removed, playback will start automatically.

3

If playback does not start automatically, press the VCR button, then press the PLAY/o button.

4

Press the STOP/p button to stop playback.

	POWER
	VCR
3	REW
5	MENU

1

4

7

VCR/TV EJECT

TV

PLAY

	F.FWD
STOP
STATUS/EXIT	CLEAR

2	3
5	6	CH
5	6
8	9
	ALT. CH
0		VOL
0

6

4

5

Press the REW(ind)/{ button to rewind the tape.

6

Press the EJECT button to remove the tape.

SPEED	TIME SEARCH	PAUSE/STILL
REC/OTR	MEMORY	SLOW	MUTE

Helpful Hints

•If the tape you want to play is already in the VCR, make sure the VCR power is on and the VCR is in VCR position. (The VCR light will appear on the display panel. If it does not, press the VCR/TV button.) Press the VCR button, then press the PLAY/o button.

•Other playback options and fea- tures are on pages 33-37.

Image 24

Contents VRA411AT Dear Philips Magnavox product owner For Customer UseThis bolt of lightning indi- cates uninsulated material Model No Serial NoFeatures Safety PrecautionsIntroduction Table of Contents Putting Batteries in the Remote Control Using the Remote ControlVCR maintenance Removing the Plastic Cover from the Front PanelHookups Without a Cable Box/Direct Broadcast System Disconnect the antenna or cable from your TVHookups Without a Cable Box/Direct Broadcast System cont’d Plug in the TV and the VCRCable Signal RF coaxial Hookups With a Cable Box/Direct Broadcast SystemConnections Recording/Viewing Any ChannelCable Signal Connect a Cable signal to the VCR’s ANTenna in JackRecording One Channel/Watching Another Cable Box/DBSHookups With a Stereo TV JackPress the VCR button, then press the Power button Turning on Your VCR2Turn on the TV Press the Menu button. The display shown below will appearAutomatic Channel Setup Press the VCR button Press the Menu buttonAutomatic Channel Setup cont’d Adding/Deleting ChannelsReviewing Memorized Channels Press the STATUS/EXIT button once or twice to exitSetting the Clock SET CLOCK, then press the F.FWD/ B buttonDaylight-Savings Time Press the VCR buttonLanguage Selection Remote Control Buttons REWind/ Button STOP/p ButtonPress again to resume normal playback MenuOn-Screen Status Displays Status Display example onlyIf you select Status ON, then select Counter only on If you select Status ON, then select Counter only OFFVCR Display Panel Front Panel Rear Panel Playing Read and follow the steps below to play a tape1Turn on the TV 2Insert a tape in the VCR Recording If the VCR light appears on the display panel, go to . IfVCR light does not appear, press the VCR/TV button once Recording One Channel/Watching Another VCR light will disappear from the VCR’s display panelOne-Touch Recording Timer Recording Do each step within 60 seconds of the previous stepPress the VCR button, then press the Menu button DailyTimer Recording cont’d Timer Recording cont’d Tape SpeedsChecking or Cancelling Timer Recordings Timer recording information for the program in the lowestProgram REVIEW, then press the F.FWD/B button Rerecording Tape Duplication Repeat Play Press the F.FWD/B button so that on appears besideClear button to reset the real-time counter to zero Real-Time Counter MemoryPress the STATUS/EXIT button to see the status display While the status display is on the screen, pressTime Search Press the VCR button Press the Time Search buttonSpecial Effects Playback Forward and Reverse Searching SP/LP/SLPSuper High Speed Searching LP/SLP Viewing a Still PictureAutomatic Operation Features Helpful Hints Helpful Hints cont’d Glossary Cable Box/DBS Output Channel 03 orSpecifications Limited Warranty Model # Serial #Index Supplied Accessories