Philips VRA411AT On-Screen Status Displays, Status Display example only, If you select Status OFF

Page 20

20 On-Screen Status Displays

A status display will appear when you press the STATUS/EXIT button or certain function buttons. The contents of the status display will vary. To choose the status display mode, follow the steps below.

If you select STATUS ON, then select COUNTER ONLY ON:

●Whenever you press the STOP/p button or the PLAY/o button, the status display will appear for five seconds. After five seconds, only the counter will remain on the screen. You must press the STATUS/EXIT button to remove it. Portions of the status display

also may appear when you press other function buttons.

If you select STATUS ON, then select COUNTER ONLY OFF:

●Whenever you press the STOP/p button or the PLAY/o button, the status display will appear for five seconds. Portions of the sta-

tus display also may appear when you press other function but- tons.

If you select STATUS OFF:

●The status display will not appear when you press function but- tons. You must press the STATUS/EXIT button to see the status display.

1

Press the VCR button, then press the MENU button.

2

Press the PLAY/o button or the STOP/p button to select VCR SET UP, then press the F.FWD/B button.

3

Press the PLAY/o button or the STOP/p button to select ON SCREEN MODE, then press the F.FWD/B button.

4

Press the PLAY/o button or the STOP/p button to select STATUS, then press the F.FWD/B button so that OFF (or ON) appears beside STATUS.

SELECT op CHOOSE B

→ STATUS	[ON]
COUNTER ONLY	[OFF]
TO END PUSH EXIT

Status Display (example only)

Current status

of tape		Time


STOP		12:00 AM
		CH10
SLP		M 1:23:45

Channel

Tape Counter

Speed and

Counter

Memory

5

If you set STATUS to OFF, go to step 6. If you set STA- TUS to ON, press the PLAY/o button or the STOP/p button to select COUNTER ONLY, then press the F.FWD/B button so that OFF (or ON) appears beside it.

6

Press the STATUS/EXIT button.

Helpful Hint

•You may not access a status display when viewing a still picture, during slow motion playback, or during for- ward or reverse searching.

Image 20

Contents VRA411AT Dear Philips Magnavox product owner For Customer UseThis bolt of lightning indi- cates uninsulated material Model No Serial NoIntroduction FeaturesSafety Precautions Table of Contents Putting Batteries in the Remote Control Using the Remote ControlVCR maintenance Removing the Plastic Cover from the Front PanelHookups Without a Cable Box/Direct Broadcast System Disconnect the antenna or cable from your TVHookups Without a Cable Box/Direct Broadcast System cont’d Plug in the TV and the VCRCable Signal RF coaxial Hookups With a Cable Box/Direct Broadcast SystemConnections Recording/Viewing Any ChannelCable Signal Connect a Cable signal to the VCR’s ANTenna in JackRecording One Channel/Watching Another Cable Box/DBSHookups With a Stereo TV JackPress the VCR button, then press the Power button Turning on Your VCR2Turn on the TV Press the Menu button. The display shown below will appearAutomatic Channel Setup Press the VCR button Press the Menu buttonAutomatic Channel Setup cont’d Adding/Deleting ChannelsReviewing Memorized Channels Press the STATUS/EXIT button once or twice to exitSetting the Clock SET CLOCK, then press the F.FWD/ B buttonDaylight-Savings Time Press the VCR buttonLanguage Selection Remote Control Buttons REWind/ Button STOP/p ButtonPress again to resume normal playback MenuOn-Screen Status Displays Status Display example onlyIf you select Status ON, then select Counter only on If you select Status ON, then select Counter only OFFVCR Display Panel Front Panel Rear Panel 1Turn on the TV 2Insert a tape in the VCR PlayingRead and follow the steps below to play a tape VCR light does not appear, press the VCR/TV button once RecordingIf the VCR light appears on the display panel, go to . If Recording One Channel/Watching Another VCR light will disappear from the VCR’s display panelOne-Touch Recording Timer Recording Do each step within 60 seconds of the previous stepPress the VCR button, then press the Menu button DailyTimer Recording cont’d Timer Recording cont’d Tape SpeedsProgram REVIEW, then press the F.FWD/B button Checking or Cancelling Timer RecordingsTimer recording information for the program in the lowest Rerecording Tape Duplication Repeat Play Press the F.FWD/B button so that on appears besideClear button to reset the real-time counter to zero Real-Time Counter MemoryPress the STATUS/EXIT button to see the status display While the status display is on the screen, pressTime Search Press the VCR button Press the Time Search buttonSpecial Effects Playback Forward and Reverse Searching SP/LP/SLPSuper High Speed Searching LP/SLP Viewing a Still PictureAutomatic Operation Features Helpful Hints Helpful Hints cont’d Glossary Cable Box/DBS Output Channel 03 orSpecifications Limited Warranty Model # Serial #Index Supplied Accessories