Philips VRA411AT owner manual Recording, If the VCR light appears on the display panel, go to . If

Page 25

1Turn on the TV.

2Insert a tape in the VCR.

4

Recording 25

Read and follow the steps below to record a television program.

1

Turn on the TV and set it to channel 3 or 4, whichever channel the CH3/CH4 switch on the back of the VCR is set to.

2

Insert a tape with its record tab intact in the VCR.

3

Press the VCR button.

4

If the VCR light appears on the display panel, go to step 5. If the

VCR light does not appear, press the VCR/TV button once.

5

Press the SPEED button until the desired tape speed appears briefly on the screen. (Details about tape speed are on

page 30.)

6

Use the CH(annel) o/p button or the Number buttons to select the channel to be recorded.

7

Press the REC(ord)/OTR button once to start recording. The REC(ord) light will appear.

8

To pause the recording, press the PAUSE/STILL button once. The REC(ord) light will flash. To resume recording, press the REC(ord)/OTR button or press the PAUSE/STILL button again. The REC(ord) light will come on again.

9

To stop recording, press the STOP/p button.

POWER

VCR/TV

EJECT

3	VCR	TV
3		PLAY			9
	REW		F.FWD
		STOP
	MENU	STATUS/EXIT		CLEAR
6	1	2	3
	4	5	6	CH
	4	5	6
	7	8	9
5			ALT. CH
		0		VOL	8
		0
	SPEED TIME SEARCH PAUSE/STILL
	REC/OTR	MEMORY	SLOW	MUTE
7

Helpful Hints

•If you press the REC(ord)/OTR but- ton when there is not a tape in the VCR, NO CASSETTE will flash on the screen.

•If you press the REC(ord)/OTR but- ton while a tape without a record tab is in the VCR, the VCR will eject the tape and PROTECTED CAS- SETTE CANNOT RECORD will flash on the screen.

•Other recording options are on pages 26-32.

•You can change the tape speed during a recording, but some distor- tion will appear on the tape.

•The VCR will record in a preset vol-

ume.

Image 25

Contents VRA411AT For Customer Use Dear Philips Magnavox product ownerThis bolt of lightning indi- cates uninsulated material Model No Serial NoSafety Precautions FeaturesIntroduction Table of Contents Using the Remote Control Putting Batteries in the Remote ControlVCR maintenance Removing the Plastic Cover from the Front PanelDisconnect the antenna or cable from your TV Hookups Without a Cable Box/Direct Broadcast SystemPlug in the TV and the VCR Hookups Without a Cable Box/Direct Broadcast System cont’dHookups With a Cable Box/Direct Broadcast System Cable Signal RF coaxialConnections Recording/Viewing Any ChannelConnect a Cable signal to the VCR’s ANTenna in Jack Cable SignalRecording One Channel/Watching Another Cable Box/DBSJack Hookups With a Stereo TVTurning on Your VCR Press the VCR button, then press the Power button2Turn on the TV Press the Menu button. The display shown below will appearPress the VCR button Press the Menu button Automatic Channel SetupAdding/Deleting Channels Automatic Channel Setup cont’dPress the STATUS/EXIT button once or twice to exit Reviewing Memorized ChannelsSET CLOCK, then press the F.FWD/ B button Setting the ClockPress the VCR button Daylight-Savings TimeLanguage Selection Remote Control Buttons STOP/p Button REWind/ ButtonPress again to resume normal playback MenuStatus Display example only On-Screen Status DisplaysIf you select Status ON, then select Counter only on If you select Status ON, then select Counter only OFFVCR Display Panel Front Panel Rear Panel Read and follow the steps below to play a tape Playing1Turn on the TV 2Insert a tape in the VCR If the VCR light appears on the display panel, go to . If RecordingVCR light does not appear, press the VCR/TV button once VCR light will disappear from the VCR’s display panel Recording One Channel/Watching AnotherOne-Touch Recording Do each step within 60 seconds of the previous step Timer RecordingPress the VCR button, then press the Menu button DailyTimer Recording cont’d Tape Speeds Timer Recording cont’dTimer recording information for the program in the lowest Checking or Cancelling Timer RecordingsProgram REVIEW, then press the F.FWD/B button Rerecording Tape Duplication Press the F.FWD/B button so that on appears beside Repeat PlayReal-Time Counter Memory Clear button to reset the real-time counter to zeroPress the STATUS/EXIT button to see the status display While the status display is on the screen, pressPress the VCR button Press the Time Search button Time SearchForward and Reverse Searching SP/LP/SLP Special Effects PlaybackSuper High Speed Searching LP/SLP Viewing a Still PictureAutomatic Operation Features Helpful Hints Helpful Hints cont’d Cable Box/DBS Output Channel 03 or GlossarySpecifications Model # Serial # Limited WarrantyIndex Supplied Accessories