Harman-Kardon 376, DPR 2005 BUSInstallation Connections, RS-232 Connections, AC Power Connections

Page 18

INSTALLATION AND CONNECTIONS

operation by changing a setting (following the instruc- tions shown on page 39) in the MULTI-ROOM SETUP menu.

NOTE: For all options, you may connect an optional IR sensor in the remote room to the DPR 2005 via an appropriate cable. Connect the sensor’s cable to the

Multiroom IR Input on the DPR 2005 and use the Zone II remote to control the room volume. Alter- natively, you may install an optional volume control between the output of the amplifiers and the speakers.

A-BUS®Installation Connections

The DPR 2005 is among the very few receivers avail- able today that offer built-in A-BUS Ready operation. When used with an optional A-BUS keypad or control module, you have all the benefits of remote zone operation without the need for an external power amplifier.

To use the DPR 2005 with an approved A-BUS prod- uct, simply connect the keypad or module that is in the remote room to the DPR 2005 using standard Category 5 wiring that is properly rated for the in-wall use specific to the installation. Terminate the wiring at the receiver end to a standard RJ-45 connector in compliance with the instructions furnished with the A-BUS module.

No further installation or adjustment is needed, as the A-BUS jack on the DPR 2005 routes the signals in and out of the keypad to their proper destination for power, signal source and control. The output fed to the A-BUS jack is determined by the DPR 2005’s multiroom system and menus.

RS-232 Connections

The DPR 2005 is equipped with an RS-232 Port a that may be used for two purposes. When the port is connected to a compatible, optional, external computer, keypad or control system the DPR 2005 is capable of bi-directional communications that enable the external system to control the DPR, and for the DPR to report status and handshake data back to the controller. Use of the RS-232 port for this type of control requires specific technical knowledge, and we recommend that any connection and programming for control be made by a trained installer or technician familiar with the equipment being used.

The RS-232 port may also be used as an access point through which the DPR 2005’s operating system and surround mode memories may be updated via connection to a compatible computer. At the time that an upgrade is available, instructions for making the connection and installing the upgrade will be available through the Product Support area of the Harman Kardon Web site at harmankardon.com.

The physical connection to the DPR 2005’s RS-232 port is a standard D-SUB 9 connection but to assure compatible and proper operation, specific software commands and pin wiring schemes may be required.

AC Power Connections

This unit is equipped with two accessory AC outlets. They may be used to power accessory devices, but they should not be used with high-current draw equip- ment such as power amplifiers. The total power draw to each outlet may not exceed 100 watts.

The Switched AC Accessory Outlet d is powered only when the unit is on. This is recommended for devices that have a mechanical power switch that may be left in the “ON” position.

NOTE: Many audio and video products go into a Standby mode when they are used with switched out- lets. This type of product may not operate properly when used with the switched outlet.

The Unswitched AC Accessory Outlet c is powered as long as the DPR is plugged into a powered AC outlet.

The DPR 2005 features a removable power cord that allows wires to be run in advance to a complex installation so that the unit itself need not be installed until it is ready for connection. When all needed connections have been made, connect the AC Power cord to the AC Power Cord Jack b.

The DPR 2005 draws significantly more current than other household devices, such as computers, that use removable power cords. For that reason, it is important that only the cord supplied with the unit (or a direct replacement of identical capacity) be used.

Once the power cord is connected, you are almost ready to enjoy the DPR 2005’s incredible power and fidelity!

18 INSTALLATION AND CONNECTIONS

Image 18
Contents DPR Digital Path ReceiverDPR 2005 Digital Path Receiver See trademark acknowledgements onThank You for Choosing Harman Kardon Description and FeaturesIntroduction Modèle pour les CanadienSafety Information Important Safety InformationStandby/On Indicator This indicator is amber To choose from the various mode optionsSurround Mode Indicators Modes, and then press the Surround Mode SelectorFrequency and preset number, if any AB C D E F G H I J I K REAR-PANEL Connections ‚ CD Audio Inputs Connect these jacks to REAR-PANEL Connections Program Button Main Remote Control FunctionsVolume Up/Down Buttons SPL Select Button EzSet Microphone Sensor LensChannel Up/Down Selector . To raise Have been pressedSpeaker Select Button Press this button Main Remote Control Functions Zone II Remote Control Functions Installation and Connections System InstallationSystem and Power Connections BUSInstallation Connections AC Power ConnectionsRS-232 Connections System Setup System ConfigurationSpeaker Placement Speaker Selection and PlacementSetting the System Configuration Memory Input SetupMaking Configuration Adjustments For DVD and the Optical Digital Input 1 ‡› Navigation Button o For added resolution Audio SetupSurround Setup Speaker OptimizerTo return to the Master Menu Speaker Setup DTS-ES Discrete. Press the ‹/› Navigation ButtonSet the unit for either 5.1 or 6.1/7.1 operation Delay Settings To bring up the Master MENU, pressMeasurement units is made, press the ⁄/¤ Output Level Adjustment Using EzSetNavigation Button o to return the cursor to the FL position MENU, press the OSD Button to bring up Manual Output Level AdjustmentUsing the EzSet remote Play shown in FigureAdditional Input Adjustments To return to normal operation of the DPRBasic Operation Volume and Tone ControlOperation Source SelectionDigital Audio Playback Surround Mode SelectionDolby Mode Select Button or Digital DTS Neo6Surround Mode Chart Selecting a Digital Source PCM PlaybackHdcd Playback Speaker/Channel Indicators Night ModeMP3 Audio Playback Tuner Operation Tape RecordingFront-Panel Connections Menu system Dim Function Output Level Trim AdjustmentMemory Backup Ments to make, press the OSD ButtonMenu system Semi-OSD Settings Advanced FeaturesMenu system Turn-On Volume Level Button is pressed is shownMenu system Multiroom Setup Multiroom OperationSpecific source Multiroom OperationButtons ç∂d OutputConfiguring the Remote Programming Remote CodesRemote’s Main Menu message Be used Learning CommandsBottom line Input Selector Button d that was justCommands from another device’s remote into the DPR remote Changing DevicesMacro Programming Macro. The choices are the Power On ButtonRemember that when you want to change devices Lower line of the display and then press the Set Button qErasing a Macro Power On VID 2/TV VID 3/Cable DPR Logic 7 hProgrammed e.g., the Power On Button 1 or Read a MacroPunch-Through Configuration Volume Punch-ThroughChannel Punch-Through EzSet Configuration When the red light under the Set Button q appearsRenaming a Device RenamingPages 27 Numeric KeysResetting the Remote Renaming Individual KeysAt this point you have two options Additional Notes on Configuring and Operating the Remote Troubleshooting Guide Processor ResetDPR 2005 Technical Specifications
Related manuals
Manual 12 pages 53.02 Kb