Harman-Kardon DPR 2005, 376 FRONT-PANEL Controls, To choose from the various mode options

Page 5

FRONT-PANEL CONTROLS

( * & ^

% $

#

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1 2

3 4 5 6 7 8 9

)

! @

A

B C D E F G HIJ I K

 

NOTE: To make it easier to follow the instructions that refer to this illustration, a larger copy may be downloaded from the Product Support section for this product at www.harmankardon.com.

The following controls and indicators are available on the DPR 2005’s front panel:

1 Standby/On Indicator

8 Input Source Selector

% Speaker/Channel Input Indicators

2 Standby/On Button

9 Tuning Mode Selector

^ Upper Display Line

3 Surround Mode Group Selector

) Set Button

& Lower Display Line

4 Surround Mode Selector

! ¤/⁄ Buttons

* Surround Mode Indicators

5 Tuning Selector

@ Front-Panel Control Door

( Remote Sensor Window

6 Tuner Band Selector

# Volume Control

 

7 Preset Station Selector

$ Input Indicators

 

The following controls and jacks are located behind the front-panel door. To open the door, press the center of the door and gently swing it down towards you.

A Main Power Switch

E Digital Input Selector

I Input/Output Indicators

B Tone Mode Button

F Delay Adjust Selector

J Coaxial 3 Digital Jack

C Speaker Selector Button

G Headphone Jack

K Video 5 Audio/Video Jacks

D Channel Adjust Selector

H Optical 3 Digital Input

 

1Standby/On Indicator: This indicator is amber

when the DPR is in the Standby mode to signal that the unit is connected to an AC power source and is ready to be put into operation. When the unit is in use, the indicator turns blue.

2Standby/On Button: When the Main Power Switch A is “ON,” press this button to turn on the DPR 2005; press it again to turn the unit off.

3Surround Mode Group Selector: Press this but- ton to select the top-level group of surround modes. Each press of the button will select one of the sur- round mode categories. Once the button is pressed so that the name of the desired surround mode category appears in the on-screen display and in the Lower Display Line &, press the Surround Mode Selector 4 to cycle through the individual modes available. For example, press this button to select Dolby

modes, and then press the Surround Mode Selector

4to choose from the various mode options.

4Surround Mode Selector: Press this button to select from among the available surround mode options for the surround mode category selected. The specific modes will vary based on the number of speakers available, the surround mode category and whether the input source is digital or analog. For exam- ple, press the Surround Mode Group Selector 3

FRONT-PANEL CONTROLS 5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Digital Path Receiver DPRSee trademark acknowledgements on DPR 2005 Digital Path ReceiverIntroduction Description and FeaturesThank You for Choosing Harman Kardon Modèle pour les CanadienImportant Safety Information Safety InformationSurround Mode Indicators To choose from the various mode optionsStandby/On Indicator This indicator is amber Modes, and then press the Surround Mode SelectorFrequency and preset number, if any AB C D E F G H I J I K REAR-PANEL Connections ‚ CD Audio Inputs Connect these jacks to REAR-PANEL Connections Volume Up/Down Buttons Main Remote Control FunctionsProgram Button SPL Select Button EzSet Microphone Sensor LensHave been pressed Channel Up/Down Selector . To raiseSpeaker Select Button Press this button Main Remote Control Functions Zone II Remote Control Functions System Installation Installation and ConnectionsSystem and Power Connections RS-232 Connections BUSInstallation ConnectionsAC Power Connections Speaker Placement System ConfigurationSystem Setup Speaker Selection and PlacementMaking Configuration Adjustments Input SetupSetting the System Configuration Memory For DVD and the Optical Digital Input 1 ‡› Navigation Button o Surround Setup Audio SetupFor added resolution Speaker OptimizerTo return to the Master Menu DTS-ES Discrete. Press the ‹/› Navigation Button Speaker SetupSet the unit for either 5.1 or 6.1/7.1 operation Measurement units is made, press the ⁄/¤ Delay SettingsTo bring up the Master MENU, press Navigation Button o to return the cursor to the FL position Output Level AdjustmentUsing EzSet Using the EzSet remote Manual Output Level AdjustmentMENU, press the OSD Button to bring up Play shown in FigureTo return to normal operation of the DPR Additional Input AdjustmentsOperation Volume and Tone ControlBasic Operation Source SelectionDolby Mode Select Button or Surround Mode SelectionDigital Audio Playback Digital DTS Neo6Surround Mode Chart Hdcd Playback Selecting a Digital SourcePCM Playback MP3 Audio Playback Speaker/Channel IndicatorsNight Mode Front-Panel Connections Tuner OperationTape Recording Memory Backup Output Level Trim AdjustmentMenu system Dim Function Ments to make, press the OSD ButtonMenu system Turn-On Volume Level Advanced FeaturesMenu system Semi-OSD Settings Button is pressed is shownMenu system Multiroom Operation Multiroom SetupButtons ç∂d Multiroom OperationSpecific source OutputRemote’s Main Menu message Configuring the RemoteProgramming Remote Codes Bottom line Learning CommandsBe used Input Selector Button d that was justChanging Devices Commands from another device’s remote into the DPR remoteRemember that when you want to change devices Macro. The choices are the Power On ButtonMacro Programming Lower line of the display and then press the Set Button qProgrammed e.g., the Power On Button 1 or Power On VID 2/TV VID 3/Cable DPR Logic 7 hErasing a Macro Read a MacroChannel Punch-Through Punch-Through ConfigurationVolume Punch-Through When the red light under the Set Button q appears EzSet ConfigurationPages 27 RenamingRenaming a Device Numeric KeysAt this point you have two options Resetting the RemoteRenaming Individual Keys Additional Notes on Configuring and Operating the Remote Processor Reset Troubleshooting GuideDPR 2005 Technical Specifications
Related manuals
Manual 12 pages 53.02 Kb
Top Page Image Contents