Harman-Kardon 376 DPR 2005 Digital Path Receiver, See trademark acknowledgements on

Page 2

DPR 2005 DIGITAL PATH RECEIVER

3Introduction

4Important Safety Information

4Unpacking

5Front-Panel Controls

8Rear-Panel Connections

11Main Remote Control Functions

15Zone II Remote Control Functions

16Installation and Connections

19System Configuration

19Speaker Placement

19System Setup

20Input Setup

22Audio Setup

22Surround Setup

24Speaker Setup

26Delay Settings

27Output Level Adjustment

27Using EzSet

28Manual Output Level Adjustment

30Operation

30Basic Operation

30Source Selection

306/8-Channel Direct Input

30Volume and Tone Control

31Surround Mode Selection

31Digital Audio Playback

32Surround Mode Chart

35Tuner Operation

35Tape Recording

35Front-Panel Connections

36Output Level Trim Adjustment

37Advanced Features

37Front-Panel Display Fade

37Display Brightness

37Turn-On Volume Level

37Semi-OSD Settings

38Full-OSD Time-Out Adjustment

39Multiroom Operation

39Multiroom Setup

39Surround Amplifier Channel Assignment

40Multiroom Operation

41Configuring the Remote

41Programming Remote Codes

41Preprogrammed Code Entry

42Automatic Code Entry

42Learning Commands

43Changing Devices

44Macro Programming

46Punch-Through Configuration

47EzSet Configuration

48Renaming

49Resetting the Remote

51Troubleshooting Guide

51Processor Reset

52Technical Specifications

See trademark acknowledgements on page 52.

Typographical Conventions

In order to help you use this manual with the remote control, front-panel controls and rear-panel connections, certain conventions have been used.

EXAMPLE – (bold type) indicates a specific remote control or front-panel button, or rear-panel connection jack

EXAMPLE – (OCR type) indicates a message that is visible on-screen or on the front-panel information display

EXAMPLE – (Synchro type) indicates a message that is displayed on the remote control’s LCD screen

1– (number in a square) indicates a specific front-panel control

A– (letter in a square) indicates a front-panel control that is behind the drop-down door

¡– (number in a circle) indicates a rear-panel connection

a– (number in an oval) indicates a button or indicator on the remote

å– (letter in an oval) indicates a button on the Zone II remote

2 TABLE OF CONTENTS

Image 2

Contents DPR Digital Path ReceiverDPR 2005 Digital Path Receiver See trademark acknowledgements onThank You for Choosing Harman Kardon Description and FeaturesIntroduction Modèle pour les CanadienSafety Information Important Safety InformationStandby/On Indicator This indicator is amber To choose from the various mode optionsSurround Mode Indicators Modes, and then press the Surround Mode SelectorFrequency and preset number, if any AB C D E F G H I J I K REAR-PANEL Connections ‚ CD Audio Inputs Connect these jacks to REAR-PANEL Connections Program Button Main Remote Control FunctionsVolume Up/Down Buttons SPL Select Button EzSet Microphone Sensor LensChannel Up/Down Selector . To raise Have been pressedSpeaker Select Button Press this button Main Remote Control Functions Zone II Remote Control Functions Installation and Connections System InstallationSystem and Power Connections RS-232 Connections BUSInstallation ConnectionsAC Power Connections System Setup System ConfigurationSpeaker Placement Speaker Selection and PlacementSetting the System Configuration Memory Input SetupMaking Configuration Adjustments For DVD and the Optical Digital Input 1 ‡› Navigation Button o For added resolution Audio SetupSurround Setup Speaker OptimizerTo return to the Master Menu Speaker Setup DTS-ES Discrete. Press the ‹/› Navigation ButtonSet the unit for either 5.1 or 6.1/7.1 operation Measurement units is made, press the ⁄/¤ Delay SettingsTo bring up the Master MENU, press Navigation Button o to return the cursor to the FL position Output Level AdjustmentUsing EzSet MENU, press the OSD Button to bring up Manual Output Level AdjustmentUsing the EzSet remote Play shown in FigureAdditional Input Adjustments To return to normal operation of the DPRBasic Operation Volume and Tone ControlOperation Source SelectionDigital Audio Playback Surround Mode SelectionDolby Mode Select Button or Digital DTS Neo6Surround Mode Chart Hdcd Playback Selecting a Digital SourcePCM Playback MP3 Audio Playback Speaker/Channel IndicatorsNight Mode Front-Panel Connections Tuner OperationTape Recording Menu system Dim Function Output Level Trim AdjustmentMemory Backup Ments to make, press the OSD ButtonMenu system Semi-OSD Settings Advanced FeaturesMenu system Turn-On Volume Level Button is pressed is shownMenu system Multiroom Setup Multiroom OperationSpecific source Multiroom OperationButtons ç∂d OutputRemote’s Main Menu message Configuring the RemoteProgramming Remote Codes Be used Learning CommandsBottom line Input Selector Button d that was justCommands from another device’s remote into the DPR remote Changing DevicesMacro Programming Macro. The choices are the Power On ButtonRemember that when you want to change devices Lower line of the display and then press the Set Button qErasing a Macro Power On VID 2/TV VID 3/Cable DPR Logic 7 hProgrammed e.g., the Power On Button 1 or Read a MacroChannel Punch-Through Punch-Through ConfigurationVolume Punch-Through EzSet Configuration When the red light under the Set Button q appearsRenaming a Device RenamingPages 27 Numeric KeysAt this point you have two options Resetting the RemoteRenaming Individual Keys Additional Notes on Configuring and Operating the Remote Troubleshooting Guide Processor ResetDPR 2005 Technical Specifications

Related manuals

Manual 12 pages 53.02 Kb