Philips SBC SC369 warranty Baby unit, Small Parent unit, Big Parent unit, Problem Solving

PROBLEM SOLVING

Problem	Possible Cause	Solution
Power light does not light	Unit is not turned on.	Turn Volume control/Off switch
(Parent unit).		clockwise (B-4, C-4).
	Batteries are low.	Recharge batteries.
Power light does not light	Unit is not turned on.	Push the Power switch (A-4) to
(Baby unit).		switch on the unit.
	AC adapter is not plugged in or	Plug in AC adapter or replace
	Batteries are exhausted.	batteries.
	AC adapter plugged into an	If the power socket has a switch,
	outlet that is not working.	turn it on.
High pitched noise.	Units are too close together.	Move Parent unit away from
		Baby unit.
	Volume too high.	Turn volume control on Parent
		unit counter-clockwise.
Parent unit batteries do not	Battery life is at an end.	Replace rechargeable battery
charge.		pack.
No sound.	Volume control on Parent unit is	Turn volume control/Off switch
	set too low.	clockwise (B-4, C-4).
	Units are out of range.	Move Parent unit closer to Baby
		unit.
Power light blinking.	Batteries are low or empty.	Parent unit:- recharge batteries.
		Baby unit:- replace batteries or
		connect to mains power.
Interference or poor	Mobile or cordless phones too	Move the phones away from the
reception.	close to the baby monitor can	units.
	cause interference.
Receiving signals from a	Both systems are using the same	Switch channels.
different baby monitor.	frequencies
System check light flashing/	Units are out of range or there is	Move parent units closer to baby
system check alarm activated	interference from another FM	unit to restore the link. Remove
	source	the other FM source.

GETTING THE UNITS READY FOR USE

Baby unit

Connect the AC power adapter (A-9) to an AC mains socket, and then connect the cord to the DC power supply socket (A-5) of the Baby unit.

If you want to use batteries, remove the battery compartment cover (A-7) using a screwdriver. Insert four 1.5V, AA batteries (not included; we recommend non-chargeable Philips Alkaline batteries), noting the + and - configuration inside the battery compartment. Put the cover back in place and tighten screw.

The Baby unit operates cordlessly for up to 30 hours on fresh batteries. The red POWER light (A-2) flashes when battery power is low. If this happens install new batteries.

Note: To switch off the Baby unit completely push the POWER button (A-4) .

Small Parent unit

The small Parent unit uses a rechargeable battery pack. This is already installed, but first it must be charged for at least 14 hours as follows before using the unit outside the charging base:

•Connect the AC power adapter (B-11) to an AC mains socket, and then connect the cord to the DC power supply socket (B-10) of the charging base (B-6).

•Place the small Parent unit inside the charging base. The red charging light (B-13) lights.

The small Parent unit can be operated now but you should leave it in the charging base until the batteries are fully charged (at least 14 hours). When the batteries are fully charged, take the small Parent unit out of the charging base and use cordlessly for up to 12 hours.

When the red POWER light (B-2) on the small Parent unit flashes, the battery power is low. Place the small Parent unit inside the charging base to recharge the batteries.

Big Parent unit

Connect the AC power adapter (C-9) to an AC mains socket, and then connect the cord to the DC power supply socket (C-8) of the big parent unit.

If you want to use batteries, remove the battery compartment cover (C-6) using a screwdriver. Insert four 1.5V, AA batteries (not included; we recommend non-chargeable Philips Alkaline batteries), noting the + and - configuration inside the battery compartment. Put the cover back in place and tighten screw.

The big Parent unit operates cordlessly for up to 30 hours on fresh batteries. The red POWER light (C-1) flashes when battery power is low. If this happens install new batteries.

8 5

IFUSC369ENbk.p65 5 14/10/2002, 11:29