Britax Britix Marathon manual Installation Forward-Facing

Page 10

Installation: Forward-Facing

LATCH Installation

•Figure A illustrates the forward-facing LATCH harness routing.

1� Verify that your vehicle is equipped with LATCH anchors..

•If LATCH anchors are not installed, you must use standard vehicle-belt installation methods.

2� If stored, remove LATCH connectors from storage pouches under cover..

3� Press and hold the LATCH adjuster release button, then pull to lengthen LATCH harness to full length.

4� Place the restraint sideways on the vehicle seat, with the back facing toward you..

•Restraint must be in the full upright position when installed in forward-facing mode with children over 33 pounds (15 kg).

5� Verify that LATCH harness is not twisted, then loosely attach the closest connector to the vehicle seat back to the adjacent LATCH anchor (Fig. B)..

•LATCH connectors should be in an upright position (as shown in Figure C), and strap should be tight and not twisted to ensure proper installation.

•A positive click confirms attachment.

•If LATCH connectors will not attach with a positive click, it may be necessary to switch the LATCH connectors as shown on pg. 21.

6� Rotate seat into forward-facing position..

A

B

Release Top

Button

C

Installation: Forward-Facing

7� Verify that LATCH harness is not twisted,

 

then loosely attach the remaining connector

 

to the remaining LATCH anchor (Fig. D)..

 

• A positive click confirms attachment.

 

8� Kneel on the child restraint to push it into

 

the vehicle seat while pulling each LATCH

 

harness tight (Fig. E)..

 

9� Verify that all connections are secure and

 

the restraint is stable. The restraint is stable

D

when it cannot be moved front to back or

side to side more than 1 inch (2..5 cm..) at

 

the belt path..

 

 

• Installation can be improved by the use of

 

the Versa-Tether®(see pages 23–25).

 

Removal

•If connected, disconnect the Versa-Tether®from the tether anchor..

•Release each LATCH harness from the LATCH anchor by pressing the red release button on the LATCH connector.

•When not in use, always store the E LATCH connectors in storage pouches sewn in cover above rear-facing lock-offs..

WARNING: Use a vehicle seat belt (not LATCH connectors) for installations with children weighing more than 48 pounds (21 kg). Refer to your vehicle's owner’s manual or contact the vehicle manufacturer for the maximum weight rating for their LATCH anchors. Unless specified otherwise by the vehicle manufacturer, assume a 48-pound child is the vehicle LATCH anchor limit..

16

17

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Marathon Table of Contents Page Safety Information Fill out the registration card and mail it in todayRestraint Features HugsVehicle Safety Belts Vehicle Seating PositionsLevel surface Installation Rear-Facing23-25 24, using anchor point RemovalLap-Belt Installation Installation Forward-Facing Your vehicle has Forward-FacingMatic locking retractor ALR, use See Checking Buckle Position onStoring the Latch Connectors Installation Forward-Facing Switching the Latch ConnectorsSwitching the Latch Harness RemovalForward-Facing Installation Installation in AircraftRear-Facing Installation Versa-TetherSee figures B and C for rear-facing installation Using the Versa-TetherRear-Facing Tether Connector Strap Energy-Absorbing TetherUsing the Chest Clip Recline AdjustmentUsing the Buckle Checking Buckle PositionSecuring Your Child 11See Checking Harness Height onChecking Harness Height Adjusting Harness HeightHarness Height Adjustment To Check Harness HeightCare and Maintenance Buckle Removal Cleaning the BuckleThoroughly Rinse using Rethreading the BuckleWarranty Limited ONE-YEAR Warranty

Britix Marathon specifications

The Britax Britix Marathon is a leading convertible car seat designed for parents who prioritize safety, comfort, and usability. This innovative car seat caters to children ranging from 5 to 65 pounds, accommodating infants, toddlers, and preschoolers alike. The Marathon is engineered with a focus on security, featuring advanced safety technologies that set it apart in the crowded market of child restraint systems.

One of the cornerstone safety features of the Britix Marathon is its SafeCell Impact Protection system. This technology includes a base that compresses during a collision, effectively lowering the center of gravity and reducing the risk of seat rotation, which in turn minimizes the force of impact on the child. The car seat also comes equipped with a steel frame that adds an extra layer of strength and stability, reinforcing the overall safety of the seat during travel.

The Marathon is designed with a high-quality harness system that boasts a no-rethread feature, allowing for easy adjustments as your child grows. This makes securing your child easier and ensures that the harness fits snugly at all times, maximizing safety and comfort. The car seat also features two recline positions that promote an optimal fit in various vehicles, providing versatility as well as comfort for your child.

Comfort is not overlooked in the Britix Marathon. The seat is generously padded with premium materials that provide a soft and cozy ride for little ones. In addition, it is equipped with breathable fabrics that help regulate temperature, ensuring your child stays comfortable throughout your journey, regardless of the weather conditions.

Parents will appreciate the ease of installation that the Marathon offers. The car seat is compatible with both the LATCH system and the vehicle seat belt, giving caregivers flexibility and convenience. An integrated lock-off helps secure the seat belt, adding an extra layer of safety during installation.

The Britix Marathon is also easy to clean, featuring a removable and washable cover. This practical design consideration helps maintain hygiene. With its blend of functionality, safety, and comfort, the Britix Britix Marathon stands out as an excellent choice for families looking for a reliable and trustworthy convertible car seat.
Top Page Image Contents