Britax Britix Marathon manual Installation Forward-Facing Switching the Latch Connectors, Removal

Page 12

Installation: Forward-Facing

Switching the LATCH Connectors

Lap-Belt Installation

•Figure A illustrates the forward-facing lap- belt-only vehicle belt route.

•When not in use, always store the LATCH connectors in storage pouches sewn in cover above rear-facing lock-offs.

1� Place the child restraint forward facing on the vehicle seat..

•Restraint must be in the full upright position when installed in forward-facing mode with children over 33 pounds (15 kg).

2� Pull the vehicle belt out, then pass it under the LATCH bar, through the forward- facing belt slots, then under the LATCH bar on the other side (Fig. B)..

3� Verify that the vehicle belt is not twisted, then buckle..

4� Kneel on the child restraint to push it into the vehicle seat while removing slack from the vehicle belt (Fig. C)..

5� Verify that the vehicle belt is tight and the child restraint is secure. The restraint is stable when it cannot be moved front to back or side to side more than 1 inch (2..5 cm..) at the belt path..

•See "Checking Buckle Position" on pg. 26.

•Installation can be improved by the use of the Versa-Tether®(see pages 23–25).

Removal

Release Versa-Tether, if used, then reverse the above directions..

A

B

C

Switching the LATCH Harness

The LATCH connectors will properly connect with the vehicle’s LATCH anchors only when the connectors are properly aligned and the harness is not twisted.

To ensure the LATCH connector is properly aligned, the connector’s red release button should face away from the vehicle seat, and the larger of the two connector sections should be on top (see figure D)..

1� Lift the front of the child restraint's cover to access the LATCH connectors..

2� Slide both LATCH connectors through rear- facing belt slots to center of restraint so both connectors are on the front side of the restraint (Fig. E)..

3� Loosen loop on one connector (Fig. F)..

4� Thread the other connector through the loop created in step 3 to switch positions (Fig. G)..

5� Slide each connector through the appropriate rear-facing belt slots to the opposite side of the restraint..

6� Replace cover and continue with installation procedure..

Storing the LATCH Connectors

When the LATCH harness is not in use, lift the cover to access LATCH storage slots. Fold the LATCH adjuster and connector, then slide each set into the adjacent slot..

Release Top Button

D

E

F

G

20

21

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Marathon Table of Contents Page Safety Information Fill out the registration card and mail it in todayRestraint Features HugsVehicle Safety Belts Vehicle Seating PositionsInstallation Rear-Facing Level surface23-25 24, using anchor point RemovalLap-Belt Installation Installation Forward-Facing Forward-Facing Matic locking retractor ALR, useYour vehicle has See Checking Buckle Position onInstallation Forward-Facing Switching the Latch Connectors Switching the Latch HarnessStoring the Latch Connectors RemovalInstallation in Aircraft Rear-Facing InstallationForward-Facing Installation Versa-TetherUsing the Versa-Tether Rear-Facing Tether Connector StrapSee figures B and C for rear-facing installation Energy-Absorbing TetherRecline Adjustment Using the BuckleUsing the Chest Clip Checking Buckle PositionSecuring Your Child 11See Checking Harness Height onAdjusting Harness Height Harness Height AdjustmentChecking Harness Height To Check Harness HeightCare and Maintenance Cleaning the Buckle Thoroughly Rinse usingBuckle Removal Rethreading the BuckleWarranty Limited ONE-YEAR Warranty

Britix Marathon specifications

The Britax Britix Marathon is a leading convertible car seat designed for parents who prioritize safety, comfort, and usability. This innovative car seat caters to children ranging from 5 to 65 pounds, accommodating infants, toddlers, and preschoolers alike. The Marathon is engineered with a focus on security, featuring advanced safety technologies that set it apart in the crowded market of child restraint systems.

One of the cornerstone safety features of the Britix Marathon is its SafeCell Impact Protection system. This technology includes a base that compresses during a collision, effectively lowering the center of gravity and reducing the risk of seat rotation, which in turn minimizes the force of impact on the child. The car seat also comes equipped with a steel frame that adds an extra layer of strength and stability, reinforcing the overall safety of the seat during travel.

The Marathon is designed with a high-quality harness system that boasts a no-rethread feature, allowing for easy adjustments as your child grows. This makes securing your child easier and ensures that the harness fits snugly at all times, maximizing safety and comfort. The car seat also features two recline positions that promote an optimal fit in various vehicles, providing versatility as well as comfort for your child.

Comfort is not overlooked in the Britix Marathon. The seat is generously padded with premium materials that provide a soft and cozy ride for little ones. In addition, it is equipped with breathable fabrics that help regulate temperature, ensuring your child stays comfortable throughout your journey, regardless of the weather conditions.

Parents will appreciate the ease of installation that the Marathon offers. The car seat is compatible with both the LATCH system and the vehicle seat belt, giving caregivers flexibility and convenience. An integrated lock-off helps secure the seat belt, adding an extra layer of safety during installation.

The Britix Marathon is also easy to clean, featuring a removable and washable cover. This practical design consideration helps maintain hygiene. With its blend of functionality, safety, and comfort, the Britix Britix Marathon stands out as an excellent choice for families looking for a reliable and trustworthy convertible car seat.
Top Page Image Contents