Powermatic TS29 operating instructions

Page 4

1.Read and understand the entire owner’s manual before attempting assembly or operation.

2.Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury.

3.Replace the warning labels if they become obscured or removed.

4.This shaper is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a shaper, do not use until proper training and knowledge have been obtained.

5.Do not use this shaper for other than its intended use. If used for other purposes, Powermatic disclaims any real or implied warranty and holds itself harmless from any injury that may result from that use.

6.Always wear approved safety glasses/face shields while using this shaper. Everyday eyeglasses only have impact resistant lenses; they are not safety glasses.

7.Before operating this shaper, remove tie, rings, watches and other jewelry, and roll sleeves up past the elbows. Remove all loose clothing and confine long hair. Non-slip footwear or anti-skid floor strips are recommended. Do not wear gloves.

8.Wear ear protectors (plugs or muffs) during extended periods of operation.

9.Some dust created by power sanding, sawing, grinding, drilling and other construction activities contain chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

Lead from lead based paint.

Crystalline silica from bricks, cement and other masonry products.

Arsenic and chromium from chemically treated lumber.

Your risk of exposure varies, depending on how often you do this type of work. To reduce your exposure to these chemicals, work in a well-ventilated area and work with approved safety equipment, such as face or dust masks that are specifically designed to filter out microscopic particles.

10.Do not operate this machine while tired or under the influence of drugs, alcohol or any medication.

11.Make certain the switch is in the OFF position before connecting the machine to the power supply.

12.Make certain the machine is properly grounded.

13.Make all machine adjustments or maintenance with the machine unplugged from the power source.

14.Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting wrenches are removed from the machine before turning it on.

15.Keep safety guards in place at all times when the machine is in use. If removed for maintenance purposes, use extreme caution and replace the guards immediately.

16.Check damaged parts. Before further use of the machine, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.

17.Provide for adequate space surrounding work area and non-glare, overhead lighting.

18.Keep the floor around the machine clean and free of scrap material, oil and grease.

19.Keep visitors a safe distance from the work area. Keep children away.

4

Image 4
Contents Tilting/Sliding Spindle Shaper Warranty and Service Warranty PeriodTable of Contents Page Page Page Introduction Specifications Contents of the Shipping Container UnpackingInterchangeable Spindle Installation AssemblyInterchangeable Spindle with Drawbar Installing Cutters Guard Assembly Fence AssemblyDust Chute Miter Gauge and Clamp Miter FenceMake sure incoming power matches voltage on motor plate Grounding InstructionsAdjustments Speed ChangeSpindle Vertical Travel Spindle LockSpindle Tilting Fence Adjustment Sliding Table AdjustmentOperating Controls OperationPosition of Collars Copying Machining with a Jig Feeding StockMaintenance LubricationTroubleshooting TroubleReplacement Parts Fence Assembly Parts List Index No. Part No Description Size QtyTS-1524041 Fence Assembly Exploded View Spindle Assembly Parts List Spindle Assembly Exploded View Cabinet Assembly Parts List Cabinet Assembly Exploded View Sliding Table Assembly Parts List Sliding Table Assembly Exploded View Speed Indicator Parts List Speed Indicator Exploded View Electrical Components Parts List Electrical Components Exploded View Quill Assembly Parts List TS-2331121 Quill Assembly Exploded View Electrical Connections TS29 Shaper New Sanford Road LaVergne, Tennessee
Related manuals
Manual 40 pages 62.41 Kb