EN Philips AVENT Express Bottle and Baby Food Warmer
Philips AVENT Express Bottle and Baby Food Warmer EN
Instructions for use
9. If the food is not ready, replace the |
9. Do not use outdoors.
10Do not let cord hang over edge of table or counter, or touch hot surfaces.
11.Do not place on or near a hot gas or electric burner, or in a heated oven.
12.Extreme caution must be used
when moving an appliance containing hot oil or other hot liquids.
13.Do not use appliance for other than intended use.
14.When in use the warmer contains hot water.
15.Before plugging in the warmer for the first time, ensure the voltage is compatible with your electrical supply by checking the label on the base of the unit.
16.Always place bottle into warmer before adding water.
17.Ensure water has been added before switching the unit on.
18.When the food has reached the required temperature, remove immediately. If left in the warmer, the temperature of the food will continue to increase.
19.The Express Warmer is fitted with a
20.This product is manufactured
to comply with the Radio Interference Requirements and the EEC Directive 89⁄336⁄EEC.
21.A short power cord has been provided to prevent the risk of it becoming entangled or being tripped over.
22.Extension cords may be used if care is exercised in their use.
23.If an extension cord is used, its electrical rating must be as great as the rating of the appliance and not draped over the edge of the table top where it could be pulled by children or tripped over. The extension cord should be a grounded type 3 wire cord.
24.Failure to follow
25.There are no serviceable parts inside the Express Warmer. Do not attempt to open, service or repair the Express Warmer yourself. For assistance call
SAVE THESE
INSTRUCTIONS
For AVENT Airflex Natural Feeding Bottles
1.Ensure basket is in place inside the warmer.
2.Place the assembled, filled bottle in the warmer with the dome cap removed.
3.For 4oz ⁄ 125ml bottles, fill the warmer with water to just above the level of milk in the bottle.
4.For larger bottles, fill the warmer to 15mm (1⁄2 inch) below the rim of the warmer.
5.Never let the water level rise above the neck of the bottle or spill over the edge of the warmer.
6.Plug the unit into an electrical outlet and click the switch to the ON position (I), the neon light will illuminate. Turn the dial to setting 3.
7.When the bottle has been in the warmer for the appropriate time (See guide), the light will flash on and off intermittently to indicate that the water surrounding the bottle is being kept at a constant temperature.
8.Remove immediately. Replace the dome cap. Shake the bottle and test the temperature of the liquid by sprinkling a few drops onto the back of your hand. Please ensure the lid of the container is tightly secured prior to shaking.
bottle in the warmer. TAKE CARE NOT |
TO OVERHEAT. The water surrounding |
the bottle will be kept at a constant |
temperature but the temperature of the |
food will continue to increase. If the food |
is too hot, allow to cool. Always test |
temperature before feeding. |
10. Once the bottle has reached the correct |
temperature and has been removed from |
the unit, switch off warmer (O) and unplug |
from the electrical outlet. |
Note: The basket can be removed when |
heating the AVENT Magic Cup and other |
makes of bottles. |
For the AVENT Tempo Natural Feeding Nurser
1.Ensure basket is in place inside the warmer.
2.Place the assembled, filled Tempo Nurser in the warmer with the dome cap removed.
3.Fill the warmer with water to the level of milk in the bottle liner.
4.Plug the unit into an electrical outlet and click the switch to the ON position
(I). The neon light will illuminate. Turn the dial to setting 2 and continue as
Note: When using Tempo liners please ensure that you choose the correct settings as using a higher selection may cause liners to burst.
4 | 5 |