Denon AVR-3300 manual Setting the bass output, System Setup Menu reappears, Parameters

Page 20

ENGLISH

4

Enter the setting.

a)

If no surround speakers are used (if “None” is set for both A and B):

ENTER

The System Setup Menu reappears.

b)

If both surround speakers A and B are used (if either “Large” or “Small” is set for both A and B):

 

The surround speaker setting screen appears.

c)If “None” is set for surround speakers A:

“None” is automatically set for surround speakers B.

NOTE:

•Select “Large” or “Small” not according to the actual size of the speaker but according to the speaker’s capacity for playing low frequency (approximately 80 Hz and below) signals. If you do not know, try comparing the sound at both settings (setting the volume to a level low enough so as not to damage the speakers) to determine the proper setting.

•Parameters

Large…… Select this when using speakers that can fully reproduce low sounds of below 80 Hz.

Small…… Select this when using speakers that cannot reproduce low sounds of below 80 Hz with sufficient volume. When this setting is selected, low frequencies of below 80 Hz are assigned to the subwoofer.

None…… Select this when no speakers are installed.

Yes/No…. Select “Yes” when a subwoofer is installed, “No” when a subwoofer is not installed.

*If the subwoofer has sufficient low frequency playback capacity, good sound can be achieved even when “Small” is set for the front, center and surround speakers.

*For the majority of speaker system configurations, using the SMALL setting for all five main speakers and Subwooofer On with a connected subwoofer will yield the best results.

Selecting the surround speakers for the different surround modes

• At this screen preset the surround speakers to be used in the different surround modes.

1

2

When either “Large” or “Small” has been set for both speakers A and B on the System Setup Menu (when using both A and B surround speakers), the surround speaker setting screen appears.

Select the surround speakers to be used in the different surround modes.

• To select the surround mode

• To select the surround speaker

A:When using surround speakers A

B:When using surround speakers B

A+B: When using both surround speakers A and B

Enter the setting.

The System Setup Menu reappears.

ENTER

*Speaker type setting when using both surround speakers A and B

If “Small” is set for either surround speakers A or B, the output is the same as when “Small” is set for both A and B.

Setting the bass output

1

At the System Setup Menu select “Bass Output”.

 

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents AVR-3300 2SAFETY Precautions Francais English Safety Instructions Table of Contents Before UsingFeatures Connecting the audio components ConnectionsConnecting video components Connecting a video component equipped with S-Video jacks Precaution when using S-jacksConnecting a monitor TV Connecting the video decksConnecting the antenna terminals AM loop antenna assembly FM antenna adopter assemblyConnecting a DVD player DVD in jacks Connecting a monitor TV Monitor OUT jackConnecting the external input EXT. in jacks Connecting the Multi Source jacksPrecautions when connecting speakers Speaker system connectionsConnections Connection the speaker terminalsProtector circuit Part Names and Functions Front PanelRemote control unit +10Setting UP the System System Setup buttonSurround Parameter button Enter buttonSurround speaker selector function Before setting up the system Setting the type of speakersSetting the bass output System Setup Menu reappearsSurround speaker setting screen appears At the System Setup Menu select Bass OutputPreparations Setting the delay timeAt the System Setup Menu select Delay Time Select the desired unit, meters or feet Select darken the desired units, Meters or FeetSetting the channel level Enter the setting System Setup Menu reappearsVolume can be adjusted between -12 dB and +12 dB in units When the Manual mode is selectedUse Channel Level screen reappearsSetting the digital inputs Setting the on-screen display OSDEXT. in & Multi Select the number of EXT. in input channelsAuto tuner presets After completing system setup On-screen display signalsInserting the batteries Remote Control UnitUsing the remote control unit Set mode switch 2 to the position for the component to be Operating Denon audio componentsOperated Tuner system buttonsPreset memory VCR Operating a video component stored in the preset memory Set the slide switch to the component to be registered VDPVCR or TV Operate the video componentLearning function System call buttons Using the system call functionSystem call function Press the SET button Storing signalsClearing system call settings Operation Before operatingFor North American model For multiple voltage modelExample CD Input mode selection functionPlaying the input source Example Stereo Input mode displayInput signal display Adjusting the sound quality Tone Listening over headphonesAfter starting playback Turning the sound off temporarily MutingChecking the currently playing program source, etc Playing one source while recording another REC OUT modeMulti-source recording/playback Display switches as follows each Time the button is pressed Button Multi source switches directlyUse the Volume buttons to adjust Volume levelPlayback using the external input EXT. in jacks Multi-source and multi-zone playbackSurround Before playing with the surround functionDolby Surround Pro Logic mode Fader functionDTS indicator lights when playing DTS sources Set the input mode to Auto or DTSSelect the Dolby/DTS Surround mode Surround parameters q Cinema EQ. Cinema Equalizer COMP. Dynamic Range CompressionLFE Low Frequency Effect Dialogue NormalizationPersonal Memory Plus Surround modes and their featuresDSP Surround Simulation DSP surround simulation Set the parametersPress the Surround Parameter button When turned clockwiseWhen turned counterclockwise Tone control setting Setting the frequency step for multiple voltage model only Listening to the RadioAuto tuning Manual tuningChecking the preset stations Initialization of the Microprocessor Recalling preset stationsLast Function Memory Troubleshooting Additional Information Optimum surround sound for different sourcesSpeaker setting examples Basic setting for primarily watching moviesWhen using different surround speakers for movies and music As seen from the sideSurround Dolby Surround Dolby Digital Dolby Surround AC-32Dolby Digital and Dolby Pro Logic Dolby Digital compatible media and playback methodsDTS Digital Surround Dolby Pro LogicDolby Pro Logic compatible media and playback methods DTS compatible media and playback methodsSurround modes and parameters Specifications
Related manuals
Manual 6 pages 32.63 Kb

AVR-3300 specifications

The Denon AVR-3300 is a powerful audio/video receiver that has garnered a reputation for its rich sound quality, robust features, and impressive performance. Positioned in the mid-range of Denon's esteemed lineup, the AVR-3300 stands out for home theater enthusiasts seeking an exceptional cinematic experience.

At the heart of the AVR-3300 is Denon’s commitment to high-quality audio reproduction. It supports Dolby Digital, DTS, and Pro Logic surround sound formats, providing a multi-dimensional audio experience that envelops the listener. The receiver features a 7.1 channel amplification system, delivering each channel with substantial power and clarity, making it ideal for expansive home theater setups.

One of the key technological advancements incorporated into the AVR-3300 is the implementation of Denon's Advanced AL24 processing. This technology enhances the digital signal, providing higher resolution sound and improved detail retrieval. Alongside this, the receiver is equipped with a 24-bit/192 kHz DAC that ensures sound fidelity across all audio formats, whether streaming from digital sources or playing traditional formats.

The AVR-3300 also features a variety of connection options, accommodating various devices and ensuring versatility. With multiple HDMI inputs, component video connections, and digital audio inputs, users can connect their Blu-ray players, gaming consoles, and streaming devices with ease. Additionally, the receiver includes a dedicated phono input for vinyl enthusiasts, allowing for direct connection to turntables.

An important characteristic of the AVR-3300 is its user-friendly interface and setup process. Denon has included an on-screen graphical user interface that simplifies navigation and adjustment of settings. The receiver also features Audyssey MultEQ technology, which automatically calibrates the sound environment by analyzing the room acoustics and adjusting speaker settings accordingly. This ensures optimal audio performance tailored to the specifics of the user’s space.

In terms of build quality, the Denon AVR-3300 is designed to be both durable and aesthetically pleasing. It sports a sleek front panel with a contemporary design, making it a stylish addition to any home entertainment system.

Overall, the Denon AVR-3300 offers a remarkable combination of sound quality, advanced technology, and user-friendly features. With its robust performance and versatile connectivity options, it remains a highly regarded choice for those looking to enhance their home theater experience.
Top Page Image Contents