Denon AVR-3300 manual Remote Control Unit, Inserting the batteries, Using the remote control unit

Page 29

ENGLISH

8REMOTE CONTROL UNIT

•The included remote control unit (RC-860) can be used to operate not only the AVR-3300 but other remote control compatible DENON components as well. Furthermore, it is equipped with a function for learning the control signals of remote control units of other manufacturers, so it can also be used to operate non-DENON remote control compatible video components.

Inserting the batteries

qRemove the remote control unit’s rear cover.

wSet two R6P/AA batteries in the battery compartment in the indicated direction.

ePut the rear cover back on.

Notes on Batteries

•Use R6P/AA batteries in the remote control unit.

•The batteries should be replaced with new ones approximately once a year, though this depends on the frequency of usage.

•Even if less than a year has passed, replace the batteries with new ones if the set does not operate even when the remote control unit is operated nearby the set.

•When inserting the batteries, be sure to do so in the proper direction, following the “≈” and “√” marks in the battery compartment.

•To prevent damage or leakage of battery fluid:

•Do not use a new battery together with an old one.

•Do not use two different types of batteries.

•Do not short-circuit, disassemble, heat or dispose of batteries in flames.

•Remove the batteries from the remote control unit when you do not plan to use it for an extended period of time.

•If the battery fluid should leak, carefully wipe the fluid off the inside of the battery compartment and insert new batteries.

•When replacing the batteries, have the new batteries ready and insert them as quickly as possible.

•The learned remote control signals may be cleared if no batteries are in the remote control unit for about 5 seconds.

The factory-installed codes are in permanent memory, however.

Using the remote control unit

30°

30°

Approx. 7 m/22 feet

•Point the remote control unit at the remote sensor on the main unit as shown on the diagram.

•The remote control unit can be used from a straight distance of approximately 7 meters/22 feet from the main unit, but this distance will be shorter if there are obstacles in the way or if the remote control unit is not pointed directly at the remote sensor.

•The remote control unit can be operated at a horizontal angle of up to 30 degrees with respect to the remote sensor.

NOTES:

•It may be difficult to operate the remote control unit if the remote sensor is exposed to direct sunlight or strong artificial light.

•Do not press buttons on the main unit and remote control unit simultaneously. Doing so may result in malfunction.

•Neon signs or other devices emitting pulse-type noise nearby may result in malfunction, so keep the set as far away from such devices as possible.

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents AVR-3300 2SAFETY Precautions Francais English Safety Instructions Before Using Table of ContentsFeatures Connections Connecting the audio componentsConnecting video components Precaution when using S-jacks Connecting a video component equipped with S-Video jacksConnecting a monitor TV Connecting the video decksAM loop antenna assembly FM antenna adopter assembly Connecting the antenna terminalsConnecting a monitor TV Monitor OUT jack Connecting a DVD player DVD in jacksConnecting the Multi Source jacks Connecting the external input EXT. in jacksSpeaker system connections Precautions when connecting speakersConnections Connection the speaker terminalsProtector circuit Front Panel Part Names and Functions+10 Remote control unitSystem Setup button Setting UP the SystemSurround Parameter button Enter buttonSurround speaker selector function Setting the type of speakers Before setting up the systemSystem Setup Menu reappears Setting the bass outputSurround speaker setting screen appears At the System Setup Menu select Bass OutputPreparations Setting the delay timeAt the System Setup Menu select Delay Time Select darken the desired units, Meters or Feet Select the desired unit, meters or feetEnter the setting System Setup Menu reappears Setting the channel levelWhen the Manual mode is selected Volume can be adjusted between -12 dB and +12 dB in unitsUse Channel Level screen reappearsSetting the on-screen display OSD Setting the digital inputsSelect the number of EXT. in input channels EXT. in & MultiAuto tuner presets On-screen display signals After completing system setupInserting the batteries Remote Control UnitUsing the remote control unit Operating Denon audio components Set mode switch 2 to the position for the component to beOperated Tuner system buttonsPreset memory VCR Set the slide switch to the component to be registered VDP Operating a video component stored in the preset memoryVCR or TV Operate the video componentLearning function System call buttons Using the system call functionSystem call function Press the SET button Storing signalsClearing system call settings Before operating OperationFor North American model For multiple voltage modelExample CD Input mode selection functionPlaying the input source Example Stereo Input mode displayInput signal display Listening over headphones Adjusting the sound quality ToneAfter starting playback Turning the sound off temporarily MutingChecking the currently playing program source, etc Playing one source while recording another REC OUT modeMulti-source recording/playback Button Multi source switches directly Display switches as follows each Time the button is pressedUse the Volume buttons to adjust Volume levelMulti-source and multi-zone playback Playback using the external input EXT. in jacksBefore playing with the surround function SurroundFader function Dolby Surround Pro Logic modeDTS indicator lights when playing DTS sources Set the input mode to Auto or DTSSelect the Dolby/DTS Surround mode COMP. Dynamic Range Compression Surround parameters q Cinema EQ. Cinema EqualizerLFE Low Frequency Effect Dialogue NormalizationPersonal Memory Plus Surround modes and their featuresDSP Surround Simulation Set the parameters DSP surround simulationPress the Surround Parameter button When turned clockwiseWhen turned counterclockwise Tone control setting Listening to the Radio Setting the frequency step for multiple voltage model onlyManual tuning Auto tuningChecking the preset stations Initialization of the Microprocessor Recalling preset stationsLast Function Memory Troubleshooting Optimum surround sound for different sources Additional InformationBasic setting for primarily watching movies Speaker setting examplesWhen using different surround speakers for movies and music As seen from the sideDolby Surround Dolby Digital Dolby Surround AC-3 Surround2Dolby Digital and Dolby Pro Logic Dolby Digital compatible media and playback methodsDolby Pro Logic DTS Digital SurroundDolby Pro Logic compatible media and playback methods DTS compatible media and playback methodsSurround modes and parameters Specifications
Related manuals
Manual 6 pages 32.63 Kb

AVR-3300 specifications

The Denon AVR-3300 is a powerful audio/video receiver that has garnered a reputation for its rich sound quality, robust features, and impressive performance. Positioned in the mid-range of Denon's esteemed lineup, the AVR-3300 stands out for home theater enthusiasts seeking an exceptional cinematic experience.

At the heart of the AVR-3300 is Denon’s commitment to high-quality audio reproduction. It supports Dolby Digital, DTS, and Pro Logic surround sound formats, providing a multi-dimensional audio experience that envelops the listener. The receiver features a 7.1 channel amplification system, delivering each channel with substantial power and clarity, making it ideal for expansive home theater setups.

One of the key technological advancements incorporated into the AVR-3300 is the implementation of Denon's Advanced AL24 processing. This technology enhances the digital signal, providing higher resolution sound and improved detail retrieval. Alongside this, the receiver is equipped with a 24-bit/192 kHz DAC that ensures sound fidelity across all audio formats, whether streaming from digital sources or playing traditional formats.

The AVR-3300 also features a variety of connection options, accommodating various devices and ensuring versatility. With multiple HDMI inputs, component video connections, and digital audio inputs, users can connect their Blu-ray players, gaming consoles, and streaming devices with ease. Additionally, the receiver includes a dedicated phono input for vinyl enthusiasts, allowing for direct connection to turntables.

An important characteristic of the AVR-3300 is its user-friendly interface and setup process. Denon has included an on-screen graphical user interface that simplifies navigation and adjustment of settings. The receiver also features Audyssey MultEQ technology, which automatically calibrates the sound environment by analyzing the room acoustics and adjusting speaker settings accordingly. This ensures optimal audio performance tailored to the specifics of the user’s space.

In terms of build quality, the Denon AVR-3300 is designed to be both durable and aesthetically pleasing. It sports a sleek front panel with a contemporary design, making it a stylish addition to any home entertainment system.

Overall, the Denon AVR-3300 offers a remarkable combination of sound quality, advanced technology, and user-friendly features. With its robust performance and versatile connectivity options, it remains a highly regarded choice for those looking to enhance their home theater experience.
Top Page Image Contents