Pacific Digital AVR 635 owner manual Manual Setup, Set Button F

Page 26

System Configuration

* N E A R

F I E L D E Q S E L E C T *

P l e a s e

s e l e c t

→1 . F L S p e a k e r

2 . C S p e a k e r

3 . F R S p e a k e r

B A C K T O M A S T E R M E N U

Figure 7f

Step 9. You will now see a Warning message similar to the one shown in Figure 7 except that it will contain an option to return to the NEAR FIELD EQ SELECT menu (Figure 7f) as well as the ability to return to the MASTER MENU. If you are ready to proceed with the test, make certain that the microphone is properly pointed toward the speaker selected for calibra- tion, press the › Navigation Button Eso that ON is highlighted and press the Set Button F.

Step 10. One short test signal will be sent to the speaker position being calibrated and after a slight pause fro the system to calculate the test results, you will see either a “Near Field Complete” message or a “Near Field Error” mes- sage. In most cases, the “Complete” message will appear, in which case you should proceed to Step 11, if an “Error” message appears, go to Step 12.

Step 11. If the test results were successful, the message shown in Figure 7g will appear. In order to properly calibrate the system, you will need to run the Near Field tests for all three front channel speakers (left, center and right). After running the test for the front left speaker, make certain that the cursor is pointing towards BACK TO NEAR FIELD and press the Set Button F. When you are taken back to the Near Field Select menu (Figure 7f) where you should repeat Steps 8 through 11 until all three front speakers have been calibrated. When that is done the EzSet/EQ process is complete and you should press the ¤ Navigation Button Eto return to the Master Menu.

* N E A R F I E L D

C O M P L E T E *

E Z S E T / E Q h a s

s u c c e s s -

F u l l y p e r f o r m e d

N e a r

F i e l d E q f o r

t h e s e l e c t e d

s p e a k e r .

→ B A C K

T O N E A R

F I E L D

B A C K

T O M A S T E R M E N U

 

 

 

Figure 7g

Step 12. If a “Near Field Error” message appears, as shown in Figure 7h, you should check to make certain that the microphone is about one meter from the speaker being tested and that the top of the microphone unit is pointing towards the speaker. You may also have to raise or lower the master volume to achieve accurate readings.

After checking these two items, as needed, make certain that the cursor is pointing to the BACK TO NEAR FIELD line and press the Set Button F. This will return you to the NEAR FIELD EQ SELECT menu (Figure 7f) where you should repeat Steps 8 through 11, adjusting the mike placement and volume level as needed until the NEAR FIELD COMPLETE menu (Figure 7g) appears after the test tone stops.

* N E A R F I E L D

E R R O R *

N e a r

F i e l d E q w a s n o t

s u c c e s s f u l .

 

P l e a s e c h e c k

m i c

P l a c e m e n t a n d v o l u m e

S e t t i n g

 

 

→ B A C K

T O

N E A R

F I E L D

B A C K

T O

M A S T E R M E N U

 

 

 

 

Figure 7h

When both the Far Field and Near Field measure- ments have been successfully completed your sys- tem is ready for use. Thanks to EzSet/EQ, the set- tings for speaker “size”, speaker crossover, chan- nel output and individual channel delay time have been automatically set and require no further adjustment. In addition, EzSet/EQ also performs a complete room equalization that tailors the sys- tem’s performance for the best possible sound with your combination of speakers, speaker place- ment and room acoustics. The next few pages in this manual detail the procedure for manually entering system data, but unless you want to view the setting information and make an adjust- ment, you are now ready to enjoy the finest in home theater and music reproduction. Go to page 35 for complete information on operating your AVR 635.

Manual Setup

In most cases it is simpler, easier and more accu- rate to let EzSet/EQ take care of entering the sys- tem parameters for speaker “size”, speaker crossover, channel output and individual channel delay time. However, if you feel that your listening room or system components are best suited to manual entry of these settings, the AVR 635 also allows you to enter or trim any of these tradition- al system parameters. Even if you do make the settings manually, we recommend that you run the EzSet/EQ tests first so that a baseline setting is established, and then make your adjustments from there. Note that once EzSet/EQ has been run you do not need to adjust all system settings, only those that you want to adjust.

To view or change the current settings, press the OSD Button Lon the remote to bring up the MASTER MENU (Figure 1). Next, press the ¤ Navigation Button Eas needed until the cursor is on the MANUAL SETUP line. Press the Set Button Fto view the MANUAL SETUP menu (Figure 8).

* M A N U A L S E T U P *

→ E Z S E T E Q : O F F O N E Z S E T A D J U S T

S P E A K E R S I Z E

S P E A K E R X O V E R

D E L A Y A D J U S T

C H A N N E L A D J U S T

B A C K T O M A S T E R M E N U

Figure 8

If you have already run the EzSet/EQ calibration system, the first line of the menu enables you to hear the difference between the settings estab- lished by EzSet/EQ. The default setting is ON, which plays the incoming source with the EzSet/EQ settings. To hear the system in a Bypass mode, with none of the equalization filters in the circuit path, press the ‹/ › Navigation Button

Eso that OFF is highlighted. Note that once changed, this setting will remain until you change it again in this menu. While you may want to use this menu option to hear the difference that EzSet/EQ makes, we recommend that you leave the setting on to take advantage of the benefits of EzSet/EQ’s advanced room correction technolo- gy.

The EZSET ADJUST line on the menu enables you to set the system’s Tilt, or high-fre- quency boost. To make this adjustment, first make sure that EZSET EQ line is set to ON, as this item is not available when EzSet EQ is not in the signal path. When the cursor is on the EZSET ADJUST line, press the Set Button F, and then press the ‹/ › Navigation Button Eto enter the desired setting. When you have com- pleted your adjustment, press the › Navigation Button Eto move the cursor down to the BACK TO MANUAL SETUP line and press

the Set Button F.

Note on Manual Setup Menus: Each of the four major manual setup menus (Speaker Size, Speaker Crossover, Delay Adjust and Channel Adjust) includes a line that reads EZSET SETTINGS. When the default setting of OFF is shown you are able to make any required adjustments that are available on that menu. However, you may change the setting to ON at any time to recall the settings established when EzSet/EQ was last run. It is also important to note that when the EzSet/EQ settings are in use, the AVR will not allow any changes to be made. To trim the settings press the ‹/ › Navigation Button Euntil the cursor is on the EZSET SETTINGS line on the menu in use and press the ‹/ › Navigation Button Eto change the setting to OFF. This will allow you to make changes to the settings on that menu.

26SYSTEM CONFIGURATION

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Power for the Digital Revolution AVR 635 Audio/ Video ReceiverTable of Contents Declaration of ConformityIntroduction Description and FeaturesHigh-bandwidth, HDTV-compatible com- ponent video switching Unpacking Introduction / Safety InformationImportant Safety Information Front Panel Controls To select between the Optical Coaxial ÓMore information Rear Panel Connections Digital Audio Outputs Connect theseUnswitched Outlet Switched Outlet AC Power Cord Jack Connect the ACRemote IR Carrier Output The output AVR 635 when appropriate upgrades are available+ and negative terminals Main Remote Control Functions Light ButtonMain Remote Control Functions Channel Direct Inputs the inputMain Remote Control Functions Main Remote Control Functions ∆ Play Forward/Reverse/Stop K Mute Zone II Remote Control FunctionsMulti IR input jack Infrared sensor that is connected to the AVR’sVideo Equipment Connections Installation and ConnectionsAudio Equipment Connections Video Connection Notes Scart A/V ConnectionsAny of the Video Audio Inputs Important Note for Adapter CablesIf you use a unit providing RGB signals on a Important Note for the Use SCART-Cinch AdaptersSystem and Power Connections Speaker Placement Speaker SelectionSystem Setup System ConfigurationUsing the On-Screen Display Input SetupA L O G So that the cursor is next to Audio SetupSurround Setup Back to Main Menu line and press the Set Button FNight Mode Settings Automatic when the menu appears on the screen Using EzSet/EQOr what the dimensions of your listening room are C K S T E R N U Manual Setup Set Button FSpeaker Setup N E M a I NSpeaker Crossover Setting Delay Settings Once to move to the next line Output Level AdjustmentManual Setup menu Button on the remoteVolume until you can hear the test noise clearly On the remoteAdditional Input Adjustments Surround Mode Chart OperationMix of the in-phase material of the left and right channels Delay time not adjustableNo delay available DTS Neo6 MusicSource Selection Controls and Use of HeadphonesBasic Operation Channel/8-Channel Direct InputDolby Digital Surround Mode SelectionDigital Audio Playback MP3 Audio Playback Rear panelPCM Audio Playback Or front panel *ÓSelecting a Digital Source Digital Bitstream IndicatorsSpeaker/Channel Indicators Front Panel In/Outputs Night ModeTape Recording Puts for Tape OutputsNormal output level adjustment for Output Level Adjustment With Source SignalsMemory Backup Dim FunctionSemi-OSD Settings Advanced FeaturesTurn On Volume Level Front-Panel-Display FadeDigital Auto-Poll Settings Advanced Features / Multiroom OperationFull-OSD Time Out Adjustment Multiroom OperationMultiroom Operation InstallationMultiroom Setup RS-232 ControlMultiroom Operation / Tuner Operation Basic Tuner OperationRDS Operation RDS TuningTuner Operation RDS Display OptionsAppears Configuring the RemotePreprogrammed Code Entry Fappears Learning CommandsAutomatic Code Entry Device Priority Programming the RemoteLearning Codes for an Input Selector Changing DevicesWill scroll to its right. For example, press Macro ProgrammingRecording a Macro At the next menu screen press Power On VID 2/TV VID 3/Cable AVR Logic 7 OErasing a Macro Read a MacroReturning the Volume Control Settings to Default Operation Punch-Through ConfigurationVolume Punch-Through Red. Press the ⁄¤ Navigation ButtonsTransport Punch-Through Returning the Channel Control Settings to Default OperationRenaming Record Pand Skip Up/Down‹/› Navigation Buttons Eas required Renaming Individual KeysAt this point you have two options Resetting the RemoteBacklight Options See page 34 for more informationAdditional Notes on Configuring and Operating the Remote Power Switch 1 is pushed Troubleshooting GuideProcessor Reset Press the AVR SelectorTechnical Specifications Harman Consumer Group International

AVR 635 specifications

The Pacific Digital AVR 635 is an advanced A/V receiver that epitomizes high-fidelity audio and video performance, making it an ideal choice for home theater enthusiasts and audiophiles alike. Known for its robust build quality and cutting-edge features, the AVR 635 offers a remarkable audiovisual experience that caters to a variety of entertainment needs.

One of the standout features of the AVR 635 is its multi-channel audio capabilities. Supporting up to seven channels, the receiver provides rich, immersive sound that enhances movies, music, and gaming experiences. With an impressive output of 100 watts per channel, users can enjoy clear and dynamic sound at a range of volume levels. The receiver also supports advanced audio formats such as Dolby TrueHD and DTS-HD Master Audio, ensuring high-definition audio playback that matches modern video quality.

In addition to powerful audio, the AVR 635 is equipped with sophisticated video processing technologies. The receiver supports upscaling from standard definition to high definition, revitalizing older content for contemporary viewing. It features multiple HDMI inputs, allowing users to connect various gaming consoles, Blu-ray players, and streaming devices with ease. The HDMI version supports 4K video pass-through, ensuring compatibility with the latest television technologies.

Another notable characteristic of the AVR 635 is its user-friendly interface. The on-screen display provides intuitive navigation through setup options and source selections, making it accessible for both novices and seasoned users. The receiver also includes a comprehensive remote control that enables quick adjustments and switching between inputs without hassle.

The AVR 635 boasts network connectivity features, allowing users to access streaming services and online music libraries. With built-in Wi-Fi and Ethernet options, the receiver can connect to home networks effortlessly. This enables streaming from platforms such as Spotify and Pandora, enriching the listening experience even further.

Moreover, the AVR 635 supports room calibration technologies, optimizing sound performance based on the unique acoustics of the environment. This feature ensures that sound reproduction is balanced and tailored, allowing every listener to enjoy the same quality regardless of their seating position.

Overall, the Pacific Digital AVR 635 combines innovative technology, powerful performance, and user-centric features, making it a top choice for anyone looking to enhance their home entertainment system. Whether for watching the latest blockbuster or enjoying a concert, the AVR 635 delivers excellence in every aspect of audio-visual reproduction.
Top Page Image Contents