Pacific Digital AVR 635 owner manual Additional Input Adjustments

Page 32

System Configuration

In addition to the controls for selecting channels and the test tone operation, the settings on this menu also allow you to reset the level settings to either the factory default of 0dB or to re-establish the settings that were entered by running EzSet/EQ.

To reset all channel levels to 0dB press ⁄/¤ Navigation Button Eso that the cursor is pointing to the LEVEL RESET line and then press the ⁄/¤ Navigation Button Eonce so ON appears in highlighted video.

To return to the settings established by EzSet/EQ, even if you have made manual changes to the output trims using the steps shown above, press ⁄/¤ Navigation Button Eso that the cur- sor is pointing to the EZSET SETTINGS line and then press the ⁄/¤ Navigation Button Eonce so ON appears in highlighted video. Remember that after turning the EzSet/EQ settings back on you must turn return to this menu line and change the setting to OFF if you wish to make any manual trim adjustments.

The final setting in this menu enables you to have the output levels remain the same for all inputs or to be adjusted differently for each (or any) input. While most listeners prefer to keep the same output levels for all sources, you may wish to raise or lower some channels, particularly the subwoofer output for a specific source such as a CD that is primarily used for music playback.

To enter individual settings for a specific channel, first make sure that you have either run EzSet/EQ and/or made any desired manual trim adjust- ments to set a baseline for all channels. After that is done, press the OSD Button Lto exit the menu system and then select the input for which you wish to enter different level settings by using either the Input Source Selectors % on the front panel or the buttons on the remote that are used to select an input source

467ç∂. Next, return to the CHANNEL OUTPUT submenu using the steps outlined above.

At the CHANNEL OUTPUT menu press ⁄/¤ Navigation Button Euntil the cursor is pointing to the LEVEL TRIM line and then press the ⁄/¤ Navigation Button Eonce so that INDEPENDENT appears in high- lighted video. When this setting is active you may change the channel output levels for any input without changing the settings previously estab- lished for another.

When all changes to the Channel Output levels and the associated level trim settings have been made press the ⁄/¤ Navigation Button E until the cursor is on the BACK TO MANUAL SETUP menu and then pressing the Set Button Fso that you may make any other adjustments to the system parameters. If the changes just made complete the manual adjust- ments needed, press the OSD Button Lto exit the menu system and resume normal system operation.

Additional Input Adjustments

After one input has been adjusted for Surround mode, digital input (if any), speaker type, and output levels, go back to the IN/OUT SETUP line on the MASTER MENU (Figure

1)and enter the settings for each input that you will use. In most cases, only the digital input and surround mode will be different from one input to the next, while the speaker type, crossover fre- quency, Night mode and output level settings will usually be the same and may be quickly entered by entering the same data used for the original input.

Once the settings outlined on the previous pages have been made, the AVR is ready for operation. While there are some additional settings to be made, these are best done after you have had an opportunity to listen to a variety of sources and different kinds of program material. These advanced settings are described on pages 41 to 42 of this manual. In addition, any of the settings made in the initial configuration of the unit may be changed at any time. As you add new or dif- ferent sources or speakers, or if you wish to change a setting to better reflect your listening taste, simply follow the instructions for changing the settings for that parameter as shown in this section.

Note that any settings changed at any time, also when the discrete buttons are used only, will be stored in memory in the AVR, also if it´s turned off completely, unless it will be reset (see page 56).

Having completed the setup and configuration process for your AVR, you are about to experience the finest in music and home-theater listening. Enjoy!

32SYSTEM CONFIGURATION

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Power for the Digital Revolution AVR 635 Audio/ Video ReceiverTable of Contents Declaration of ConformityIntroduction Description and FeaturesHigh-bandwidth, HDTV-compatible com- ponent video switching Unpacking Introduction / Safety InformationImportant Safety Information Front Panel Controls To select between the Optical Coaxial ÓMore information Rear Panel Connections Digital Audio Outputs Connect theseUnswitched Outlet Switched Outlet AC Power Cord Jack Connect the ACRemote IR Carrier Output The output AVR 635 when appropriate upgrades are available+ and negative terminals Main Remote Control Functions Light ButtonMain Remote Control Functions Channel Direct Inputs the inputMain Remote Control Functions Main Remote Control Functions Zone II Remote Control Functions Multi IR input jack∆ Play Forward/Reverse/Stop K Mute Infrared sensor that is connected to the AVR’sVideo Equipment Connections Installation and ConnectionsAudio Equipment Connections Scart A/V Connections Any of the Video Audio InputsVideo Connection Notes Important Note for Adapter CablesIf you use a unit providing RGB signals on a Important Note for the Use SCART-Cinch AdaptersSystem and Power Connections Speaker Placement Speaker SelectionSystem Configuration Using the On-Screen DisplaySystem Setup Input SetupA L O G Audio Setup Surround SetupSo that the cursor is next to Back to Main Menu line and press the Set Button FNight Mode Settings Automatic when the menu appears on the screen Using EzSet/EQOr what the dimensions of your listening room are C K S T E R N U Manual Setup Set Button FSpeaker Setup N E M a I NSpeaker Crossover Setting Delay Settings Output Level Adjustment Manual Setup menuOnce to move to the next line Button on the remoteVolume until you can hear the test noise clearly On the remoteAdditional Input Adjustments Surround Mode Chart OperationDelay time not adjustable No delay availableMix of the in-phase material of the left and right channels DTS Neo6 MusicControls and Use of Headphones Basic OperationSource Selection Channel/8-Channel Direct InputDolby Digital Surround Mode SelectionDigital Audio Playback Rear panel PCM Audio PlaybackMP3 Audio Playback Or front panel *ÓSelecting a Digital Source Digital Bitstream IndicatorsSpeaker/Channel Indicators Night Mode Tape RecordingFront Panel In/Outputs Puts for Tape OutputsOutput Level Adjustment With Source Signals Memory BackupNormal output level adjustment for Dim FunctionAdvanced Features Turn On Volume LevelSemi-OSD Settings Front-Panel-Display FadeAdvanced Features / Multiroom Operation Full-OSD Time Out AdjustmentDigital Auto-Poll Settings Multiroom OperationInstallation Multiroom SetupMultiroom Operation RS-232 ControlMultiroom Operation / Tuner Operation Basic Tuner OperationRDS Tuning Tuner OperationRDS Operation RDS Display OptionsAppears Configuring the RemotePreprogrammed Code Entry Fappears Learning CommandsAutomatic Code Entry Programming the Remote Learning Codes for an Input SelectorDevice Priority Changing DevicesWill scroll to its right. For example, press Macro ProgrammingRecording a Macro Power On VID 2/TV VID 3/Cable AVR Logic 7 O Erasing a MacroAt the next menu screen press Read a MacroPunch-Through Configuration Volume Punch-ThroughReturning the Volume Control Settings to Default Operation Red. Press the ⁄¤ Navigation ButtonsReturning the Channel Control Settings to Default Operation RenamingTransport Punch-Through Record Pand Skip Up/Down‹/› Navigation Buttons Eas required Renaming Individual KeysResetting the Remote Backlight OptionsAt this point you have two options See page 34 for more informationAdditional Notes on Configuring and Operating the Remote Troubleshooting Guide Processor ResetPower Switch 1 is pushed Press the AVR SelectorTechnical Specifications Harman Consumer Group International

AVR 635 specifications

The Pacific Digital AVR 635 is an advanced A/V receiver that epitomizes high-fidelity audio and video performance, making it an ideal choice for home theater enthusiasts and audiophiles alike. Known for its robust build quality and cutting-edge features, the AVR 635 offers a remarkable audiovisual experience that caters to a variety of entertainment needs.

One of the standout features of the AVR 635 is its multi-channel audio capabilities. Supporting up to seven channels, the receiver provides rich, immersive sound that enhances movies, music, and gaming experiences. With an impressive output of 100 watts per channel, users can enjoy clear and dynamic sound at a range of volume levels. The receiver also supports advanced audio formats such as Dolby TrueHD and DTS-HD Master Audio, ensuring high-definition audio playback that matches modern video quality.

In addition to powerful audio, the AVR 635 is equipped with sophisticated video processing technologies. The receiver supports upscaling from standard definition to high definition, revitalizing older content for contemporary viewing. It features multiple HDMI inputs, allowing users to connect various gaming consoles, Blu-ray players, and streaming devices with ease. The HDMI version supports 4K video pass-through, ensuring compatibility with the latest television technologies.

Another notable characteristic of the AVR 635 is its user-friendly interface. The on-screen display provides intuitive navigation through setup options and source selections, making it accessible for both novices and seasoned users. The receiver also includes a comprehensive remote control that enables quick adjustments and switching between inputs without hassle.

The AVR 635 boasts network connectivity features, allowing users to access streaming services and online music libraries. With built-in Wi-Fi and Ethernet options, the receiver can connect to home networks effortlessly. This enables streaming from platforms such as Spotify and Pandora, enriching the listening experience even further.

Moreover, the AVR 635 supports room calibration technologies, optimizing sound performance based on the unique acoustics of the environment. This feature ensures that sound reproduction is balanced and tailored, allowing every listener to enjoy the same quality regardless of their seating position.

Overall, the Pacific Digital AVR 635 combines innovative technology, powerful performance, and user-centric features, making it a top choice for anyone looking to enhance their home entertainment system. Whether for watching the latest blockbuster or enjoying a concert, the AVR 635 delivers excellence in every aspect of audio-visual reproduction.
Top Page Image Contents