Pacific Digital AVR 635 owner manual Technical Specifications

Page 57

Technical Specifications

Audio Section

Stereo Mode

Continuous Average Power (FTC)

90 Watts per channel, 20Hz–20kHz,

@ < 0.07% THD, both channels driven into 8 ohms

5/7 Channel Surround Modes

Power Per Individual Channel

Front L&R channels:

75 Watts per channel,

@ < 0.07% THD, 20Hz–20kHz into 8 ohms

Center channel:

75 Watts, @ < 0.07% THD, 20Hz–20kHz into 8 ohms

Surround (L & R Side, L & R Back) channels: 75 Watts per channel,

@ < 0.07% THD, 20Hz–20kHz into 8 ohms

Input Sensitivity/Impedance

 

Linear (High Level)

200mV/47kohms

Signal-to-Noise Ratio (IHF-A)

95dB

Surround System Adjacent Channel Separation

Analog Decoding

40dB

(Pro Logic, etc.)

 

Dolby Digital (AC-3)

55dB

DTS

55dB

Frequency Response

 

@ 1W (+0dB, –3dB)

10Hz– 130kHz

High Instantaneous

 

Current Capability (HCC)

±50 Amps

Transient Intermodulation

 

Distortion (TIM)

Unmeasurable

Rise Time

16 µsec

Slew Rate

40V/µsec**

Supplied Accessories

The following accessory items are supplied with the AVR 635.

If any of these items are missing, please contact Harman Kardon customer service at www.harmankardon.com.

•A system remote control

•A Zone II remote control

•An microphone

•Extender rod for microphone

•An AM loop antenna

•An FM wire antenna

•Six AAA batteries

FM Tuner Section

 

Frequency Range

87.5 –108MHz

Usable Sensitivity

IHF 1.3 µV/13.2dBf

Signal-to-Noise Ratio

Mono/Stereo: 70/68dB (DIN)

Distortion

Mono/Stereo: 0.15/0.2%

Stereo Separation

40dB @ 1kHz

Selectivity

±400kHz: 70dB

Image Rejection

80dB

IF Rejection

90dB

AM Tuner Section

 

Frequency Range

520–1710kHz

Signal-to-Noise Ratio

45dB

Usable Sensitivity

Loop: 500µV

Distortion

1kHz, 50% Mod: 0.8%

Selectivity

±10kHz: 30dB

Video Section

 

Video Format

PAL/NTSC

Input Level/Impedance

1Vp-p/75 ohms

Output Level/Impedance

1Vp-p/75 ohms

Video Frequency Response

 

(Composite and S-Video)

10Hz–8MHz (–3dB)

Video Frequency

 

Response (Component)

10Hz-50MHz (-3dB)

General

 

Power Requirement

AC 220-240V/50Hz

Power Consumption

59W idle, 1040W maximum

 

(7 channels driven)

Dimensions (Max)

 

Width

440mm

Height

165mm

Depth

435mm

Weight

18.6 kg

Depth measurement includes knobs, buttons and terminal connections.

Height measurement includes feet and chassis.

All features and specifications are subject to change without notice.

Harman Kardon and Power for the Digital Revolution are registered trademarks of Harman International Industries, Incorporated.

is a trademark of Harman International Industries, Inc. (Patent No. 5,386,478).

*Manufactured under license from Dolby Laboratories.

“Dolby,” “Pro Logic,” “Pro Logic II,” "Pro Logix IIx" and the Double-D symbol are trademarks of Dolby Laboratories. Confidential Unpublished

Works. ©1992–1999 Dolby Laboratories, Inc. All rights reserved.

DTS and DTS Surround, DTS-ES and DTS Neo:6 are trademarks of Digital Theater Systems, Inc.

Logic 7 is a registered trademark of Harman International Industries, Incorporated.

HDCD is a registered trademark of Pacific Microsonics, Inc.

A-BUS and A-BUS Ready are registered trademarks of Leisure Tech Electronics Pty Ltd Australia.

TiVo is a registered trademark of TiVo, Inc.

Replay TV is a registered trademark of Digital Networks North America, Inc.

**Without input anti slewing and output isolation networks.

TECHNICAL SPECIFICATIONS 57

Page 56 Page 58
Image 57
Page 56 Page 58
Contents AVR 635 Audio/ Video Receiver Power for the Digital RevolutionDeclaration of Conformity Table of ContentsDescription and Features High-bandwidth, HDTV-compatible com- ponent video switchingIntroduction Introduction / Safety Information Important Safety InformationUnpacking Front Panel Controls Coaxial Ó More informationTo select between the Optical Digital Audio Outputs Connect these Rear Panel ConnectionsSwitched Outlet AC Power Cord Jack Connect the AC Unswitched OutletAVR 635 when appropriate upgrades are available + and negative terminalsRemote IR Carrier Output The output Light Button Main Remote Control FunctionsChannel Direct Inputs the input Main Remote Control FunctionsMain Remote Control Functions Main Remote Control Functions Multi IR input jack Zone II Remote Control Functions∆ Play Forward/Reverse/Stop K Mute Infrared sensor that is connected to the AVR’sInstallation and Connections Audio Equipment ConnectionsVideo Equipment Connections Any of the Video Audio Inputs Scart A/V ConnectionsVideo Connection Notes Important Note for Adapter CablesImportant Note for the Use SCART-Cinch Adapters If you use a unit providing RGB signals on aSystem and Power Connections Speaker Selection Speaker PlacementUsing the On-Screen Display System ConfigurationSystem Setup Input SetupA L O G Surround Setup Audio SetupSo that the cursor is next to Back to Main Menu line and press the Set Button FNight Mode Settings Using EzSet/EQ Or what the dimensions of your listening room areAutomatic when the menu appears on the screen C K S T E R N U Set Button F Manual SetupN E M a I N Speaker SetupSpeaker Crossover Setting Delay Settings Manual Setup menu Output Level AdjustmentOnce to move to the next line Button on the remoteOn the remote Volume until you can hear the test noise clearlyAdditional Input Adjustments Operation Surround Mode ChartNo delay available Delay time not adjustableMix of the in-phase material of the left and right channels DTS Neo6 MusicBasic Operation Controls and Use of HeadphonesSource Selection Channel/8-Channel Direct InputSurround Mode Selection Digital Audio PlaybackDolby Digital PCM Audio Playback Rear panelMP3 Audio Playback Or front panel *ÓDigital Bitstream Indicators Speaker/Channel IndicatorsSelecting a Digital Source Tape Recording Night ModeFront Panel In/Outputs Puts for Tape OutputsMemory Backup Output Level Adjustment With Source SignalsNormal output level adjustment for Dim FunctionTurn On Volume Level Advanced FeaturesSemi-OSD Settings Front-Panel-Display FadeFull-OSD Time Out Adjustment Advanced Features / Multiroom OperationDigital Auto-Poll Settings Multiroom OperationMultiroom Setup InstallationMultiroom Operation RS-232 ControlBasic Tuner Operation Multiroom Operation / Tuner OperationTuner Operation RDS TuningRDS Operation RDS Display OptionsConfiguring the Remote Preprogrammed Code EntryAppears Learning Commands Automatic Code EntryFappears Learning Codes for an Input Selector Programming the RemoteDevice Priority Changing DevicesMacro Programming Recording a MacroWill scroll to its right. For example, press Erasing a Macro Power On VID 2/TV VID 3/Cable AVR Logic 7 OAt the next menu screen press Read a MacroVolume Punch-Through Punch-Through ConfigurationReturning the Volume Control Settings to Default Operation Red. Press the ⁄¤ Navigation ButtonsRenaming Returning the Channel Control Settings to Default OperationTransport Punch-Through Record Pand Skip Up/DownRenaming Individual Keys ‹/› Navigation Buttons Eas requiredBacklight Options Resetting the RemoteAt this point you have two options See page 34 for more informationAdditional Notes on Configuring and Operating the Remote Processor Reset Troubleshooting GuidePower Switch 1 is pushed Press the AVR SelectorTechnical Specifications Harman Consumer Group International

AVR 635 specifications

The Pacific Digital AVR 635 is an advanced A/V receiver that epitomizes high-fidelity audio and video performance, making it an ideal choice for home theater enthusiasts and audiophiles alike. Known for its robust build quality and cutting-edge features, the AVR 635 offers a remarkable audiovisual experience that caters to a variety of entertainment needs.

One of the standout features of the AVR 635 is its multi-channel audio capabilities. Supporting up to seven channels, the receiver provides rich, immersive sound that enhances movies, music, and gaming experiences. With an impressive output of 100 watts per channel, users can enjoy clear and dynamic sound at a range of volume levels. The receiver also supports advanced audio formats such as Dolby TrueHD and DTS-HD Master Audio, ensuring high-definition audio playback that matches modern video quality.

In addition to powerful audio, the AVR 635 is equipped with sophisticated video processing technologies. The receiver supports upscaling from standard definition to high definition, revitalizing older content for contemporary viewing. It features multiple HDMI inputs, allowing users to connect various gaming consoles, Blu-ray players, and streaming devices with ease. The HDMI version supports 4K video pass-through, ensuring compatibility with the latest television technologies.

Another notable characteristic of the AVR 635 is its user-friendly interface. The on-screen display provides intuitive navigation through setup options and source selections, making it accessible for both novices and seasoned users. The receiver also includes a comprehensive remote control that enables quick adjustments and switching between inputs without hassle.

The AVR 635 boasts network connectivity features, allowing users to access streaming services and online music libraries. With built-in Wi-Fi and Ethernet options, the receiver can connect to home networks effortlessly. This enables streaming from platforms such as Spotify and Pandora, enriching the listening experience even further.

Moreover, the AVR 635 supports room calibration technologies, optimizing sound performance based on the unique acoustics of the environment. This feature ensures that sound reproduction is balanced and tailored, allowing every listener to enjoy the same quality regardless of their seating position.

Overall, the Pacific Digital AVR 635 combines innovative technology, powerful performance, and user-centric features, making it a top choice for anyone looking to enhance their home entertainment system. Whether for watching the latest blockbuster or enjoying a concert, the AVR 635 delivers excellence in every aspect of audio-visual reproduction.
Top Page Image Contents