Arcam AV888 Speakers, Or DTS decoding modes, DVD, the AVR600 selects, Dolby Pro Logic, Source

Page 57

Problem

Check that...

Sound only comes from some

< you have an appropriate surround source selected and playing.

of the speakers

< the DVD disc is encoded in the appropriate format, and the correct format

 

 

has been selected in the disc start menu of the DVD player (if applicable).

 

< the DVD player has been set to output ‘bitstream’ audio on the digital

 

output.

 

< the display window indicates that the disc you are playing is a multichannel

 

recording (you may need to press the INFO key several times until you get to

 

the ‘incoming format’ display).

 

< all the speakers are correctly connected to the speaker terminals and are

 

secure.

 

< you have not selected ‘Stereo’ as the decoding mode.

 

< your speaker balance is correct.

 

< you have configured the unit to include all the speakers in your system.

Unable to select Dolby Digital

The AVR600/AV888 can only apply Dolby Digital and DTS decoding to sources

or DTS decoding modes

which have been encoded in the same format.

 

Check that:

 

< digital source is selected and connected.

 

< the source is playing appropriately encoded material.

 

< the DVD disc is encoded in the appropriate format and that the correct

 

format has been selected in the disc start menu of the DVD player (if

 

applicable).

 

< the DVD player has been set to output ‘bitstream’ audio on the digital output

 

(not PCM).

When playing a Dolby Digital

< you have a digital connection from your DVD player.

DVD, the AVR600 selects

< sometimes Dolby Digital DVD discs contain material at either the beginning

Dolby Pro Logic

or the end of the main movie that is not in full 5.1 format, but in two-

 

 

channel or Pro Logic decoding.

Hum on the analogue input

< all cables are making a good connection. If necessary withdraw the cable

 

from the connector and plug it fully in again (turn the power off before

 

doing this).

 

< the connections inside the source cable connector are not broken or badly

 

soldered.

 

< if the hum originates only when one particular source component is

 

connected, that an aerial cable, or dish connection to this source is ground

 

isolated. Contact your installation contractor.

There is radio or television

< where the interference is coming from. Switch off each source component in

reception interference

turn, then any other equipment. Most electronic equipment does generate

 

low levels of interference.

 

< try re-arranging cabling from the nuisance source away from other cabling.

 

< ensure that the cabling used is high quality, specified for its purpose, and is

 

properly screened.

 

< if the problem persists, contact your dealer.

Problem

Check that...

The source switching changes

< there are no static or impulse interference problems caused by nearby power

randomly or freezes on one

equipment switching, e.g., heating or air conditioning control. Switch the

source

unit off, wait ten seconds, then switch it on again to clear an operating

 

problem. Contact your installer if the problem returns or persists.

 

< there is no direct sunlight shining on the infra-red detector behind the front

 

panel display.

Volume is always too loud

< the ‘max on volume’ setting is not set too high.

when I turn on

 

When Zone 2 or 3 is put into

< the ‘zone standby‘ setting in the setup menu is set to LOCAL.

standby, the main zone is also

 

switched off

 

When a USB memory device is

< a USB memory device is connected that conforms to the mass storage class.

connected, ‘USB’ is not shown

< a USB hub is not being used.

in the network client’s list of

 

folders

 

If files on a USB memory

< the USB device is formatted in FAT16 or FAT32.

device cannot be played:

< the USB device does not have multiple partitions.

 

 

< the files are in a compatible format.

If files on a computer cannot

< the files are in a compatible format.

be played

< the computer is connected via a network and not USB – the AVR600/AV888

 

 

USB port cannot be used for a direct connection to a computer

If you cannot connect to a

< the Ethernet cable you are using is correctly connected between the

wired network

AVR600/AV888 and the network hardware.

 

< the network is set up for fixed IP addressing and you have the AVR600/

 

AV888 set to use DHCP.

 

< the network is set up for DHCP and you have the AVR600/AV888 set to use

 

fixed IP addressing.

If you cannot connect to a

< the station is still broadcasting or is not congested – try again later.

favourite internet radio station

 

If the internet radio station

< the radio station does not have a low bit rate (use the INFO key to find this or

sound quality is poor or

look on the OSD).

broken

< the network is not slow or congested.

 

English

E-55

Page 56 Page 58
Image 57
Page 56 Page 58
Contents N d b o o k AVR surround amplifier / AV processor AVR600 / AV888Important safety instructions Safety GuidelinesSafety compliance Class II productClass II produit Instructions de sécurité importantesRespect des consignes de sécurité Page Professional Installation? ContentsDIY setup? WelcomeBefore you Begin… Standby power PowerPlacing the unit Interconnect cablesTrademark acknowledgements Connectors, see Audio connectorsComponent, S-Video Optical and electrical digital Two-channel Multichannel, seeGeneral Hdmi connectorsMaking connections Component/RGB Video CompositeZone 3 connectors Zone 2 connectorsDigital audio connectors MCH input Inputs Phono Analogue audio Front panel AUX inputAnalogue record outputs Front panel Phones socketEnglish Satellite receiver DVD playerCD player Use the Composite connection if HdmiConnecting an iPod using the Arcam rDock Aerial connectors AVR600 only Radio ConnectorsWhere fitted Internal wire of the aerialConnecting an aerial Data connectors Network connectors USB connector Other ConnectorsRS232 serial connector RLead/rDockInfra-red IR connectors English Trigger connectorsTip Modulated signal Sleeve Ground RoomConnecting subwoofers Connecting speakers AVR600 onlySpeakers Speaker cablesSubwoofer CentreFront left and right Surround left and rightOperation Switching onOperating your AVR600 or AV888 Selecting a sourceUsing Zone 2 Updating firmware using a PCExtended front panel menu Front panel Operation CR102 universal remote controller Inserting batteries into the remote controlUsing the remote control Useful information Device Mode / Source keysCode blink-back Controlling other devicesIPod commands AMP Device ModeDVD Device Mode TUN Device ModeNetwork commands Highlighted menu on the screenAV Device Mode SAT Device ModeVCR Device Mode PVR Device ModeCD Device Mode English Speaker types Essential SetupSpeaker Distances Speaker LevelsAuto speaker setup Auto speaker SetupProblems Using a subwooferNavigating the setup menu Setup menusTreble Bass Input ConfigGeneral Setup Plii Dimension Plii Centre Width Plii PanoramaGeneral information and system controls Spkr Types Auto SetupSpkr Distance Spkr LevelsVideo Outputs Video InputsProgressive scan playback Important points to rememberMode Zone SettingsNetwork For Stereo sourcesDecoding Modes IntroductionTwo-channel source modes Decoding modes Multichannel source modesVolume Leveller SettingsDolby Volume is a sophisticated new Calibration OffsetEnglish Tuner Operation Default unlock code is Sirius errorsOperation Locking ChannelsSelecting the playback source Network/usb OperationUSB playback Internet radio stationsEnglish XLR balanced line outputs AV888 only External AmplifiersSW2, SW3 Subwoofer 2 and SubwooferZone Multi-room Set upZone 2 and 3 control outputs Audio outputsZone English Code Learning Customising CR102Volume punch-through Creating MacrosKey Mover Locking/Unlocking a specific Device Mode Mode MoverTo restore a moved Device Mode key to its original state Copy a key between Device ModesResetting the CR102 Mode key IR punch-throughProblem Check that When I turn on Volume is always too loudSwitched off Wired networkContinual improvement policy SpecificationsWorldwide Guarantee Product GuaranteeClaims under guarantee Problems?Device code Tables ICE HCMIRT ITCSBR RFTSEG SEIGPX AVPKEC KLHNTL ADBUPC DKKCGV CATDCE ENGSKY+ AsciTPS UECYES SH215E Issue 4301-7333+0
Related manuals
Manual 74 pages 35.94 Kb Manual 74 pages 48.95 Kb Manual 68 pages 27.09 Kb

AV888, AVR600 specifications

The Arcam AVR600 is a high-performance AV receiver that is designed for audiophiles and home cinema enthusiasts who seek a premium audio and video experience. This receiver stands out with its array of features and technologies that elevate sound quality and user experience.

At the heart of the AVR600 is its high-fidelity amplification system. The receiver is equipped with a robust 7-channel amplification setup, delivering a total output of 120 watts per channel into 8 ohms. This power enables the AVR600 to reproduce dynamic audio with precision, whether it be for movies, music, or gaming. The class G amplifier design offers exceptional efficiency and reduces distortion, ensuring that sound remains clean and focused even at higher volumes.

The AVR600 boasts extensive connectivity options to accommodate various audio and video sources. It features multiple HDMI inputs and outputs supporting 3D video and 4K scaling, providing flexibility for connecting modern devices. The unit also includes analog and digital inputs, a dedicated phono input for vinyl enthusiasts, and support for multi-room audio setups. With its built-in Bluetooth and network streaming capabilities, users can easily access high-resolution audio files from their digital libraries or popular streaming services.

One of the key technologies in the AVR600 is its advanced room correction system, known as Dirac Live. This sophisticated calibration tool analyzes the acoustics of the room and automatically adjusts the output of the receiver to compensate for any sound anomalies. As a result, listeners experience optimized sound tailored to their specific environment, enhancing the overall listening experience.

For video performance, the AVR600 supports a range of formats, including Dolby Atmos and DTS:X, ensuring an immersive home theater experience with enveloping surround sound. It also features advanced video processing capabilities, allowing users to upscale standard-definition and high-definition content to near 4K quality, further enhancing picture clarity.

In terms of user interface, the AVR600 provides an intuitive on-screen display and a well-designed remote control that makes navigating through settings and options seamless. The receiver is also compatible with smartphone apps for additional convenience, allowing users to control playback and settings directly from their mobile devices.

Overall, the Arcam AVR600 is a versatile audio-visual receiver that combines power, connectivity, and advanced technologies to create an exceptional home entertainment experience. Its unique blend of performance and flexibility makes it an excellent choice for those looking to invest in high-quality audio and video solutions for their homes.
Top Page Image Contents